Investigating the influence of WEDM process parameters in machining of hybrid aluminum composites
Amresh Kumar,Neelkant Grover,Alakesh Manna,Jasgurpreet Singh Chohan,Raman Kumar,Sunpreet Singh,Chander Prakash,Catalin I. Pruncu,Catalin I. Pruncu +8 more
Reads0
Chats0
TLDR
In this article, the influence of input process parameters on machinability of wire electrical discharge machining (WEDM) process for machining of tripliers was investigated.Abstract:
This article presents an experimental investigation to assess the influence of input process parameters of machinability of wire electrical discharge machining (WEDM) process for machining of tripl...read more
Citations
More filters
Journal Article
The Design and Analysis of Experiments
TL;DR: This book by a teacher of statistics (as well as a consultant for "experimenters") is a comprehensive study of the philosophical background for the statistical design of experiment.
Journal ArticleDOI
Evaluation of fracture processes under shear with the use of DIC technique in fly ash concrete and accurate measurement of crack path lengths with the use of a new crack tip tracking method
TL;DR: In this article, the optical and contactless DIC technique was used for the examination of fracture processes in concrete with fly ash under shear loading, and the results showed that unmodified concrete are characterised by greater brittleness, whereas composites made on the basis of the binary binder behave as quasi-plastic materials in the fracture process.
Journal ArticleDOI
Studies of Fracture Toughness in Concretes Containing Fly Ash and Silica Fume in the First 28 Days of Curing.
TL;DR: In this article, the fracture toughness of concretes with two mineral additives, assessed at an early age, was evaluated using a modern and useful digital image correlation (DIC) technique to assess macroscopic cracks.
Journal ArticleDOI
Advanced production routes for metal matrix composites
TL;DR: An overview of advanced production routes for metal matrix composites can be found in this article, where the authors highlight challenges and present a future prospectus for MMCs, and discuss additive manufacturing as a promising method for the production of MMC products.
Journal ArticleDOI
Revealing the WEDM Process Parameters for the Machining of Pure and Heat-Treated Titanium (Ti-6Al-4V) Alloy
Nitin Kumar Gupta,Nalin Somani,Chander Prakash,Ranjit Singh,Arminder Singh Walia,Sunpreet Singh,Catalin I. Pruncu +6 more
TL;DR: In this article, the authors focused on machining Ti-6Al-4V using wire electrical discharge machining (WEDM) and conducting numerous experiments to establish the machining parameters.
References
More filters
Journal Article
The Design and Analysis of Experiments
TL;DR: This book by a teacher of statistics (as well as a consultant for "experimenters") is a comprehensive study of the philosophical background for the statistical design of experiment.
Journal ArticleDOI
Metal matrix composites – From science to technological significance
TL;DR: The metal matrix composites (MMCs) have been transformed from a topic of scientific and intellectual interest to a material of broad technological and commercial significance over the past two decades as mentioned in this paper.
Journal ArticleDOI
A review on the production of metal matrix composites through stir casting – Furnace design, properties, challenges, and research opportunities
TL;DR: In this article, a bottom tapping stir casting furnace with electromagnetic and ultrasonic stirrer along with squeeze attachment is recommended for the production of metal matrix composites, based on the critical assessment of the literature, especially the mechanical properties of the produced MMCs.
Journal ArticleDOI
Taguchi design and response surface methodology based analysis of machining parameters in CNC turning under MQL
Murat Sarikaya,Abdulkadir Güllü +1 more
TL;DR: In this paper, the effect of machining parameters such as cooling condition, cutting speed, feed rate and depth of cut on arithmetic average roughness (Ra) and average maximum height of the profile (Rz) when turning of AISI 1050 steel was investigated.
Journal ArticleDOI
A study on machinability of Al/SiC-MMC
A. Manna,B. Bhattacharayya +1 more
TL;DR: In this article, the machinability of silicon carbide particulate aluminium metal matrix composite during turning using fixed rhombic tools was investigated during the fabrication of Al/SiC-MMC and the influence of machining parameters, e.g. cutting speed, feed rate and depth of cut on the tools wear and built-up edges (BUEs) were analyzed.