Journal ArticleDOI
Rheological and morphological behaviour of blends of polycarbonate with unmodified and maleic anhydride grafted ABS
Reads0
Chats0
TLDR
In this article, a mixture of polycarbonate (PC) and maleic anhydride grafted ABS (MABS) was prepared by melt blending, using a single-screw extruder with a special mixing head over the whole range of compositions.About:
This article is published in Polymer.The article was published on 1998-11-01. It has received 53 citations till now. The article focuses on the topics: Maleic anhydride.read more
Citations
More filters
Journal ArticleDOI
Effects of Compatibilizer and Graphene Oxide on the Impact Strength of PC/ABS Blend
TL;DR: In this article, the effects of both the grafted ABS-g-MAH and the added graphene oxide (GO) on the impact strength of poly- carbonate (PC)/poly(acrylonitrile-butadiene-styrene) (ABS) blends were discussed.
Dissertation
Structuration des mélanges ABS/PC en vue du recyclage des DEEE.
TL;DR: In this article, a travail focusing on the amelioration des mecaniques des melanges ABS/PC (70%/30% en masse) en structurant the morphologie de melanges sous formes allongees (fibres et/ou lamelles).
Characterization of Short Glass Fiber-Reinforced PC/ABS Blends
TL;DR: In this article, the authors found that the viscosity of filled and unfilled polymers increases with an increasing content of the short glass fiber and that the glass fiber adhesion at the interface between glass fibers and polymer matrix is crucial to the effective reinforcement of the fiber.
Journal ArticleDOI
Linear viscoelastic and morphological description of multiphase systems affected by processing parameters
TL;DR: In this article, the influence of processing methods, in terms of comparing compression and injection moldings, on the rheological behavior of polycarbonate (PC)/acrylonitrile-butadiene-styrene (ABS) blends and PC/ABS/glass fibers composites is presented.
Journal ArticleDOI
Preparation and Evaluation of the Morphology, Flammability, and Mechanical Properties of the Acrylonitrile‐Butadiene‐Styrene/Poly (vinyl chloride) Blends
TL;DR: In this article, two grades of acrylonitrile butadiene styrene (ABS) with three different compounds of poly (vinyl chloride) (PVC) were prepared via melt processing and their morphology, flammability, and physical and mechanical properties were investigated.
References
More filters
Journal ArticleDOI
An investigation of instability of phase morphology of blends of nylons with polyethylenes and polystyrenes and effects of compatibilizing agents
TL;DR: In this article, the phase morphology of blends of nylons with polyethylenes and polystyrenes is investigated and the effects of compatibilizing agents are discussed.
Journal ArticleDOI
Rubber toughened polybutylene terephthalate: influence of processing on morphology and impact properties
TL;DR: In this paper, the authors used dynamic mechanical analysis to detect the presence of interzones existing between the polybutylene terephthalate (PBT) matrix and the EPR random copolymer.
Journal ArticleDOI
Polycarbonate/ABS blends: Processability, thermal properties, and mechanical and impact behavior
TL;DR: In this paper, a Brabender-like apparatus and compression molded in sheets was used for the preparation of PC/ABS blends, encompassing the whole composition range between PC and ABS, and two very different mechanical tests were performed: (a) tensile stress-strain on unnotched specimens at a very low deformation rate, showing a decreased PC ductility in blends with ABS additions; and (b) flexural impact tests (Charpy mode), where a strong synergistic effect was detected in a restricted composition range (20-30% ABS).
Journal ArticleDOI
Polycarbonate/ABS blends: A literature review
Roberto Greco,Andrea Sorrentino +1 more
TL;DR: The articles here presented and discussed offer an almost exhaustive survey of the work done until now on these commercial materials, particularly with respect to the phase compatibility.
Related Papers (5)
Recycling of polycarbonate by blending with maleic anhydride grafted ABS
Effect of reactive compatibilizers on the mechanical properties of polycarbonate/poly(acrylonitrile-butadiene-styrene) blends
Sie Chin Tjong,Yuezhong Meng +1 more