Renewable energy sources like wind, sun, and hydro are seen as a reliable alternative to the traditional energy sources such as oil, natural gas, or coal. Distributed power generation systems (DPGSs) based on renewable energy sources experience a large development worldwide, with Germany, Denmark, Japan, and USA as leaders in the development in this field. Due to the increasing number of DPGSs connected to the utility network, new and stricter standards in respect to power quality, safe running, and islanding protection are issued. As a consequence, the control of distributed generation systems should be improved to meet the requirements for grid interconnection. This paper gives an overview of the structures for the DPGS based on fuel cell, photovoltaic, and wind turbines. In addition, control structures of the grid-side converter are presented, and the possibility of compensation for low-order harmonics is also discussed. Moreover, control strategies when running on grid faults are treated. This paper ends up with an overview of synchronization methods and a discussion about their importance in the control

/pdf/overview-of-control-and-grid-synchronization-for-distributed-2nx31ovpe9.pdf

Overview of Control and Grid Synchronization for Distributed Power Generation Systems

The use of distributed energy resources is increasingly being pursued as a supplement and an alternative to large conventional central power stations. The specification of a power-electronic interface is subject to requirements related not only to the renewable energy source itself but also to its effects on the power-system operation, especially where the intermittent energy source constitutes a significant part of the total system capacity. In this paper, new trends in power electronics for the integration of wind and photovoltaic (PV) power generators are presented. A review of the appropriate storage-system technology used for the integration of intermittent renewable energy sources is also introduced. Discussions about common and future trends in renewable energy systems based on reliability and maturity of each technology are presented

/pdf/power-electronic-systems-for-the-grid-integration-of-4s5cxjhatl.pdf

Power-Electronic Systems for the Grid Integration of Renewable Energy Sources: A Survey

This review focuses on inverter technologies for connecting photovoltaic (PV) modules to a single-phase grid. The inverters are categorized into four classifications: 1) the number of power processing stages in cascade; 2) the type of power decoupling between the PV module(s) and the single-phase grid; 3) whether they utilizes a transformer (either line or high frequency) or not; and 4) the type of grid-connected power stage. Various inverter topologies are presented, compared, and evaluated against demands, lifetime, component ratings, and cost. Finally, some of the topologies are pointed out as the best candidates for either single PV module or multiple PV module applications.

A review of single-phase grid-connected inverters for photovoltaic modules

This book, written by two major figures in adaptive control, provides a wealth of material for researchers, practitioners, and students. While some researchers in adaptive control may note the absence of a particular topic, the book‘s scope represents a high-gain instrument. It can be used by designers of control systems to enhance their work through the information on many new theoretical developments, and can be used by mathematical control theory specialists to adapt their research to practical needs. The book is strongly recommended to anyone interested in adaptive control.

Adaptive Control

Solid-state switch-mode rectification converters have reached a matured level for improving power quality in terms of power-factor correction (PFC), reduced total harmonic distortion at input AC mains and precisely regulated DC output in buck, boost, buck-boost and multilevel modes with unidirectional and bidirectional power flow. This paper deals with a comprehensive review of improved power quality converters (IPQCs) configurations, control approaches, design features, selection of components, other related considerations, and their suitability and selection for specific applications. It is targeted to provide a wide spectrum on the status of IPQC technology to researchers, designers and application engineers working on switched-mode AC-DC converters. A classified list of more than 450 research publications on the state of art of IPQC is also given for a quick reference.

/pdf/a-review-of-single-phase-improved-power-quality-ac-dc-2pm6h4zjxq.pdf

A review of single-phase improved power quality AC-DC converters

Preface. 1. Introduction. I: Converters in Equilibrium. 2. Principles of Steady State Converter Analysis. 3. Steady-State Equivalent Circuit Modeling, Losses, and Efficiency. 4. Switch Realization. 5. The Discontinuous Conduction Mode. 6. Converter Circuits. II: Converter Dynamics and Control. 7. AC Equivalent Circuit Modeling. 8. Converter Transfer Functions. 9. Controller Design. 10. Input Filter Design. 11. AC and DC Equivalent Circuit Modeling of the Discontinuous Conduction Mode. 12. Current Programmed Control. III: Magnetics. 13. Basic Magnetics Theory. 14. Inductor Design. 15. Transformer Design. IV: Modern Rectifiers and Power System Harmonics. 16. Power and Harmonics in Nonsinusoidal Systems. 17. Line-Commutated Rectifiers. 18. Pulse-Width Modulated Rectifiers. V: Resonant Converters. 19. Resonant Conversion. 20. Soft Switching. Appendices: A. RMS Values of Commonly-Observed Converter Waveforms. B. Simulation of Converters. C. Middlebrook's Extra Element Theorem. D. Magnetics Design Tables. Index.

/pdf/fundamentals-of-power-electronics-57kz8pj23p.pdf

Fundamentals of Power Electronics

This paper describes a complete digital PWM controller IC for high-frequency switching converters. Novel architecture and configurations of the key building blocks are A/D converter, compensator, and digital pulse-width modulator, are introduced to meet the requirements of tight output voltage regulation, high-speed dynamic response, and programmability without external passive components. The implementation techniques are experimentally verified on a prototype chip that takes less than 1 mm/sup 2/ of silicon area in a standard 0.5 /spl mu/ digital complementary metal oxide semiconductor (CMOS) process and operates at the switching frequency of 1 MHz.

/pdf/high-frequency-digital-pwm-controller-ic-for-dc-dc-2vpkurwra9.pdf

High-frequency digital PWM controller IC for DC-DC converters

Compared to basic converter topologies (buck, boost, buck-boost, Cuk, etc.), pulse-width modulation (PWM) converters with quadratic DC conversion ratios, M(D)=D/sup 2/, M(D)=D/sup 2//(1-D) or M(D)=D/sup 2//(1-D)/sup 2/, offer a significantly wider conversion range. For a given minimum ON-time and, consequently, for a given minimum duty ratio D/sub min/, D/sup 2/ in the numerator of M(D) yields a much lower limit on the minimum attainable conversion ratio. By applying a systematic synthesis procedure, six novel single-transistor converter configurations with quadratic DC conversion ratios are found. The simpler, single-transistor realization is the most important advantage over the straightforward cascade of two basic converters. As far as conversion efficiency is concerned, it is clear that a single-stage converter is usually a better choice than a two-stage converter. The quadratic converters proposed are intended for applications where conventional single-stage converters are inadequate-for high-frequency applications where the specified range of input voltages and the specified range of output voltages call for an extremely large range of conversion ratios. >

/pdf/switching-converters-with-wide-dc-conversion-range-58fu5icwgc.pdf

Switching converters with wide DC conversion range

This paper explores predictive digital current programmed control for valley, peak or average current. The control laws are derived for the three basic converters: buck, boost, and buck-boost. It is found that for each variable of interest (valley, peak or average current) there is a choice of the appropriate pulse-width modulation method to achieve predictive digital current control without oscillation problems. The proposed digital control techniques can be used in a range of power conversion applications, including rectifiers with power factor correction (PFC). Very low current distortion meeting strict avionics requirements (400-800 Hz line frequency) is experimentally demonstrated on a digitally controlled boost PFC employing predictive average current programmed control.

/pdf/predictive-digital-current-programmed-control-276hrdxplj.pdf

Predictive digital current programmed control

This paper reviews some of the major approaches to modeling and simulation in power electronics, and provides references that can serve as a starting point for the extensive literature on the subject. The major focus of the paper is on averaged models of various kinds, but sampled-data models are also introduced. The importance of hierarchical modeling and simulation is emphasized.

Dragan Maksimovic

Papers

Fundamentals of Power Electronics

High-frequency digital PWM controller IC for DC-DC converters

Switching converters with wide DC conversion range

Predictive digital current programmed control

Modeling and simulation of power electronic converters