Showing papers by "John G. Speer published in 2020"

Perspectives on Quenching and Tempering 4340 Steel

Abstract: Steels are ubiquitous due to their affordability and the landscape of useful properties that can be generated for engineering applications. But to further expand the performance envelope, one must be able to understand and control microstructure development by alloying and processing. Here we use multiscale, advanced characterization to better understand the structural and chemical evolution of AISI 4340 steel after quenching and tempering (Q&T), including the role of quench rate and short-time, isothermal tempering below 573 K (300 °C), with an emphasis on carbide formation. We compare the microstructure and/or property changes produced by conventional tempering to those produced by higher temperature, short-time “rapid” tempering. We underscore that no single characterization technique can fully capture the subtle microstructure changes like carbon redistribution, transition carbide and/or cementite formation, and retained austenite decomposition that occur during Q&T. Only the use of multiple techniques begins to unravel these complexities. After controlled fast or slow quenching, η transition carbides clearly exist in the microstructure, likely associated with autotempering of this high martensite start temperature (Ms) steel. Isothermal tempering below 598 K (325 °C) results in the relief of carbon supersaturation in the martensite, primarily by the formation of η transition carbides that exhibit a range of carbon levels, seemingly without substitutional element partitioning between the carbide and matrix phases. Hagg transition carbide is present between 300 °C and 325 °C. After conventional tempering at or above 598 K (325 °C) for 2 h, cementite is predominant, but small amounts of cementite are also present in other conditions, even after quenching. Previous work has indicated that silicon (Si) and substitutional elements partition between the cementite, which initially forms under paraequilibrium conditions, and the matrix. Phosphorous (P) may also be preferentially located at cementite/matrix interfaces after high temperature tempering. Slower quench rates result in greater amounts of retained austenite compared to those after fast quenching, which we attribute to increased austenite stability resulting from “autopartitioning”. Rapid, high temperature tempering is also found to diminish tempered martensite embrittlement (TME) believed to be associated with the extent of austenite decomposition, resulting in mechanical properties not attainable by conventional tempering, which may have important implications with respect to industrial heat treatment processes like induction tempering. Controlling the amount and stability of retained austenite is not only relevant to the properties of Q&T steels, but also next-generation advanced high strength steels (AHSS) with austenite/martensite mixtures.

Effect of microsegregation on carbide-free bainitic transformation in a high-silicon cast steel

Abstract: A high silicon cast steel was studied in the as-cast condition in order to characterise its solidification macrostructure and microsegregation. The steel, poured into 32 mm-keel-block-shaped moulds...

Rapid Tempering: Opportunities and Challenges

Abstract: Rapid tempering involves shorter times and faster heating rates compared to conventional tempering. Utilizing rapid tempering via industrial processes, such as induction heating, not only offers the opportunity for improved mechanical properties, but also for reduced processing times and energy costs. The current study demonstrates an improvement in toughness with rapid tempering by examining impact toughness at a constant tempering parameter for short-time (1 s) and conventional (3600 s) tempering treatments of 4340 steel. Fracture behavior is found to complement the observed toughness behavior, where higher impact energy conditions are associated with a greater percentage of ductile fracture. The role of the Hollomon–Jaffe tempering parameter, as well as the use of hardness as a metric to characterize degree of tempering, is discussed in light of the results comparing rapid and conventional tempering conditions. This study indicates promising mechanical properties associated with short-time tempering, especially within the tempered martensite embrittlement (TME) regime, and exposes challenges associated with predicting performance strictly based on hardness when rapid tempering is utilized.

Hot Strip Mill Processing Simulations on a Ti-Mo Microalloyed Steel Using Hot Torsion Testing

Abstract: Precipitation strengthened, fully ferritic microstructures in low-carbon, microalloyed steels are used in applications requiring enhanced stretch-flange formability. This work assesses the influence of thermomechanical processing on the evolution of austenite and the associated final ferritic microstructures. Hot strip mill processing simulations were performed on a low-carbon, titanium-molybdenum microalloyed steel using hot torsion testing to investigate the effects of extensive differences in austenite strain accumulation on austenite morphology and microstructural development after isothermal transformation. The gradient of imposed shear strain with respect to radial position inherent to torsion testing was utilized to explore the influence of strain on microstructural development for a given simulation, and a tangential cross-section technique was employed to quantify the amount of shear strain that accumulated within the austenite during testing. Greater austenite shear strain accumulation resulted in greater refinement of both the prior austenite and polygonal ferrite grain sizes. Further, polygonal ferrite grain diameter distributions were narrowed, and the presence of hard, secondary phase constituents was minimized, with greater amounts of austenite strain accumulation. The results indicate that extensive austenite strain accumulation before decomposition is required to achieve desirable, ferritic microstructures.

Selected developments in nb-microalloyed forgings for induction hardening, and pearlitic wire rod

Abstract: Niobium-microalloying technology has been increasingly applied in a wide range of steel applications over the past half-century to enhance properties; namely to increase strength, control microstructure, and enable a variety of applications. To achieve desired performance levels, thermomechanically processed microalloyed steels are widely supplied by the steel industry for high volume applications in hot-rolled plate, sheet and structural steels. However, in steel long products and forgings, the final properties are often generated by downstream users, after heat-treatment, surface hardening, forging or wire drawing. Two examples are presented highlighting advancements associated with Nb-microalloying to enhance microstructures and properties developed during thermomechanical and/or downstream processing. In the first example, a 0.02 wt. pct. Nb addition was made to a medium-carbon bar steel intended for induction-hardening applications requiring fatigue and fracture resistance in bending and torsion. The Nb addition as well as thermomechanical bar processing led to beneficial refinement of both the pre-induction and post-induction microstructures. In the second example, a 0.01 wt. pct. Nb addition to a high-carbon wire rod was found to refine the pearlite interlamellar spacing, and increase the hardness.