scispace - formally typeset
Journal ArticleDOI

The effect of slip distribution on the monotonic and cyclic ductility of AlLi binary alloys

T.H. Sanders, +1 more
- 01 May 1982 - 
- Vol. 30, Iss: 5, pp 927-939
Reads0
Chats0
TLDR
In this paper, the authors correlated the monotonic and cyclic properties of three AlLi alloys with the slip behavior and found that cracks nucleated at grain boundary ledges during tensile tests and propagated either transgranularly or intergranularally along precipitate free zones.
About
This article is published in Acta Metallurgica.The article was published on 1982-05-01. It has received 214 citations till now. The article focuses on the topics: Slip (materials science) & Lüders band.

read more

Citations
More filters
Journal ArticleDOI

Precipitation strengthening at ambient and elevated temperatures of heat-treatable Al(Sc) alloys

TL;DR: In this article, the authors investigated yield strength at ambient temperature and creep resistance between 225 and 300°C in dilute Al(Sc) alloys containing coherent Al3Sc precipitates, which were grown by heat-treatments to radii in the range 1.4-9.6 nm.
Journal ArticleDOI

Grain boundary ductile fracture in precipitation hardened aluminum alloys

TL;DR: In this article, the authors reviewed microstructural studies of grain boundary (gb) fracture in precipitation hardened aluminum alloys with respect to the three main ideas that have been developed to explain the gb fracture surfaces.
Journal ArticleDOI

Strength, deformation, fracture behaviour and ductility of aluminium-lithium alloys.

TL;DR: In this paper, the deformation characteristics and fracture behavior of aluminium alloys are examined with specific reference to ageing condition of the alloy, the matrix slip characteristics, and the nature, volume fraction and distribution of strengthening precipitates.
Journal ArticleDOI

Microstructural control of toughness in aluminium-lithium alloys

TL;DR: In this paper, the deformation behavior of Al-Li-based alloys containing zirconium as a grain-refining addition is investigated, and it is shown that the poor toughness properties are attributed to the intense coplanar slip associated with δ' (Al3Li) precipitation being unimpeded by the grain structure as a result of the pronounced deformation texture present in the sheet product.
Journal ArticleDOI

Effects of cold work on precipitation in Al-Cu-Mg-(Ag) and Al-Cu-Li-(Mg-Ag) alloys

TL;DR: In this paper, the effects of cold work prior to aging on precipitation hardening in selected Al-Mg-(Ag) and Al-Cu-Li-(Mg-Ag) alloys were investigated.
References
More filters
Journal ArticleDOI

Metallurgical factors affecting fracture toughness of aluminum alloys

TL;DR: The fracture toughness of aluminum alloys depends on a) the extent of the heavily strained region ahead of the crack tip, which is a function of the yield strength arad modulus, b) the size of the ligaments which is related tof c, the volume fraction of cracked particles, and c) the work of rupturing ligaments.
Journal ArticleDOI

On the strength of solid solution alloys

TL;DR: In this paper, it was shown that motion of a dislocation through a crystal with short-range order partially destroys the order and produces an interface of positive mean energy γ per unit area, an additional stress τ = γ b is required to force the dislocation along the slip plane.
Journal ArticleDOI

Precipitation Characteristics of Aluminium-Lithium Alloys

B. Noble, +1 more
TL;DR: In this paper, structural ageing characteristics of aluminium alloys containing 2 and 4 wt.-% lithium are reported and thin-film electron microscopy was used to confirm the ordered L12-typestructure of the δ′ and to study the precipitate size and distribution over a range of ageing temperatures.
Related Papers (5)
Trending Questions (1)
How does linear slip distribution on edges influence the mechanical properties of materials?

The provided paper does not specifically discuss the influence of linear slip distribution on edges on the mechanical properties of materials.