Showing papers by "Fabrício Mezzomo Collares published in 2018"

Physicochemical and Microbiological Assessment of an Experimental Composite Doped with Triclosan-Loaded Halloysite Nanotubes.

Abstract: This study is aimed at evaluating the effects of triclosan-encapsulated halloysite nanotubes (HNT/TCN) on the physicochemical and microbiological properties of an experimental dental composite. A resin composite doped with HNT/TCN (8% w/w), a control resin composite without nanotubes (HNT/TCN-0%) and a commercial nanofilled resin (CN) were assessed for degree of conversion (DC), flexural strength (FS), flexural modulus (FM), polymerization stress (PS), dynamic thermomechanical (DMA) and thermogravimetric analysis (TGA). The antibacterial properties (M) were also evaluated using a 5-day biofilm assay (CFU/mL). Data was submitted to one-way ANOVA and Tukey tests. There was no significant statistical difference in DC, FM and RU between the tested composites (p > 0.05). The FS and CN values attained with the HNT/TCN composite were higher (p < 0.05) than those obtained with the HNT/TCN-0%. The DMA analysis showed significant differences in the TAN δ (p = 0.006) and Tg (p = 0) between the groups. TGA curves showed significant differences between the groups in terms of degradation (p = 0.046) and weight loss (p = 0.317). The addition of HNT/TCN induced higher PS, although no significant antimicrobial effect was observed (p = 0.977) between the groups for CFUs and (p = 0.557) dry weight. The incorporation of HNT/TCN showed improvements in physicochemical and mechanical properties of resin composites. Such material may represent an alternative choice for therapeutic restorative treatments, although no significance was found in terms of antibacterial properties. However, it is possible that current antibacterial tests, as the one used in this laboratory study, may not be totally appropriate for the evaluation of resin composites, unless accompanied with aging protocols (e.g., thermocycling and load cycling) that allow the release of therapeutic agents incorporated in such materials.

Tantalum oxide as filler for dental adhesive resin

Abstract: The purpose of this study was to formulate and evaluate an adhesive resin with tantalum oxide Ta2O5 was evaluated by scanning electron microscopy and laser diffraction The adhesive was formulated with methacrylate monomers and photoinitiators Ta2O5 was added into the adhesive at 1, 2, 5 and 10 wt% One group remained without filler (control group) Ta2O5 distribution, radiopacity (n=5), degree of conversion (DC) (n=3), softening in solvent (n=5) and ultimate tensile strength (UTS) (n=10) were evaluated Data were analyzed by one-way ANOVA and Tukey's test (α=005) Spherical nanometric Ta2O5 was arranged in 335 µm particles The groups over 5 wt% presented higher radiopacity (p 005) and UTS (p>005) Tantalum oxide is a promising alternative for adhesive formulation and it could be further tested for biomimetic remineralization

Effect of nanostructured zirconium dioxide incorporation in an experimental adhesive resin

Abstract: The aim of this study was to evaluate the influence of nanostructured zirconium dioxide incorporation in an experimental adhesive resin. ZrO2 particles were characterized by X-ray diffraction (XRD), micro-Raman spectroscopy and Brunauer–Emmett–Teller (B.E.T). Experimental adhesive resins were formulated with 0, 0.5, 1, 4.8, and 9.1% ZrO2 in weight. The adhesives were evaluated based on degree of conversion (DC), radiopacity, softening in solvent and microtensile bond strength (μTBS) 24 h and after 1 year of aging. Mineral deposition at the hybrid layer was assessed with micro-Raman spectroscopy at the baseline and after 14 days. XRD showed monoclinic and tetragonal phases of ZrO2.particles. B.E.T data revealed a surface area of 37.41 m2/g, and typical chemical groups were shown on the Raman spectra. The addition of ZrO2 did not influence the radiopacity. The addition of 4.8% and 9.1 wt.% ZrO2 showed higher initial hardness with increased softening in solvent (P < 0.05) and promoted mineral deposition at the dentin interface. DC was significantly increased in the group with 1% ZrO2 (P < 0.05). The μTBS test showed difference on the group with 9.1 wt.% of ZrO2, with a significant reduction after aging. The incorporation of ZrO2 promoted mineral deposition on the adhesive interface and the addition of 1 wt.% caused a significant increase on the DC without compromising the other physicochemical characteristics, which may prove promising for the development of new dental adhesive systems. The mineral deposition on the hybrid layer can result in a longer stability of the adhesive, thus delaying the hydrolytic degradation.

Methacrylate-based root canal sealer containing chlorexidine and α-tricalcium phosphate.

Abstract: The aim of this study was to develop and to characterize a methacrylate-based root canal sealer containing chlorhexidine (CHX) and α-tricalcium phosphate (α-TCP). Experimental dual cure methacrylate-based sealer was produced containing 0, 2.5, or 5 wt% of CHX and 0, 25, or 50 wt% of α-TCP. Experimental sealers were evaluated based on flow, film thickness, radiopacity, degree of conversion (DC), degradation in water, pH and antibacterial activity. Flow ranged from 15.09 ± 0.11 to 17.47 ± 0.42 mm. All groups presented mean film thickness lower than 50 µm and had radiopacity equivalent to 3 mmAl. DC was higher than 60% for all compositions. The weight loss (WL) ranged 0.12-3.47%. The groups containing 5% of CHX presented the highest WL and the lower pH values after 28 days of water immersion. All chlorexidine-compositions exhibited antibacterial efficacy against Enterococcus faecalis on direct contact and agar diffusion tests. CHX and α-TCP addition at an experimental methacrylate-based root canal sealer influenced the physicochemical properties and provided antibacterial properties. The incorporation of CHX and α-TCP could be an alternative to antibacterial sealers with potential to improve periapical healing in endodontic treatments. © 2017 Wiley Periodicals, Inc. J Biomater Res Part B: 106B: 1439-1443, 2018.

Effect on adhesion of a nanocapsules-loaded adhesive system.

Abstract: This study aimed to evaluate the in situ degree of conversion, contact angle, and immediate and long-term bond strengths of a commercial primer and an experimental adhesive containing indomethacin- and triclosan-loaded nanocapsules (NCs). The indomethacin- and triclosan-loaded NCs, which promote anti-inflammatory and antibacterial effects through controlled release, were incorporated into the primer at a concentration of 2% and in the adhesive at concentrations of 1, 2, 5, and 10%. The in situ degree of conversion (DC, n=3) was evaluated by micro-Raman spectroscopy. The contact angle of the primer and adhesive on the dentin surface (n = 3) was determined by an optical tensiometer. For the microtensile bond strength µTBS test (12 teeth per group), stick-shaped specimens were tested under tensile stress immediately after preparation and after storage in water for 1 year. The data were analyzed using two-way ANOVA, three-way ANOVA and Tukey's post hoc tests with α=0.05. The use of the NC-loaded adhesive resulted in a higher in situ degree of conversion. The DC values varied from 75.07 ± 8.83% to 96.18 ± 0.87%. The use of NCs in only the adhesive up to a concentration of 5% had no influence on the bond strength. The contact angle of the primer remained the same with and without NCs. The use of both the primer and adhesive with NCs (for all concentrations) resulted in a higher contact angle of the adhesive. The longitudinal μTBS was inversely proportional to the concentration of NCs in the adhesive system, exhibiting decreasing values for the groups with primer containing NCs and adhesives with increasing concentrations of NCs. Adhesives containing up to 5% of nanocapsules and primer with no NCs maintained the in situ degree of conversion, contact angle, and immediate and long-term bond strengths. Therefore, the NC-loaded adhesive can be an alternative method for combining the bond performance and therapeutic effects. The use of an adhesive with up to 5% nanocapsules containing indomethacin and triclosan and a primer with no nanocapsules maintained the long-term bond performance.

Influence of Octacalcium Phosphate addition on physical-mechanical properties of Glass Ionomer Cement

Abstract: OBJECTIVE: The aim of this study was to evaluate the influence of octacalcium phosphate (OCP) addition to conventional glass ionomer cement (GIC). METHODOLOGY: A commercial glass ionomer cement (Vidrion R – S.S. White Artigos Dentarios Ltda – Rio de Janeiro, Brazil) was used in this study. OCP was added to powder in 1.5 and 3 wt%. GIC without OCP addition was used as control. Specimens were produced to evaluate radiopacity, setting time and diametral tensile strength of cements. Radiopacity was assessed by phosphor plate system with alluminium step-wedge for comparison. For setting time determination, Gilmore needle (100 g) was used to determine final setting reaction. Diametral tensile strength was measured in a universal testing machine. Data were analyzed by one-way ANOVA at a significance level of 95%. RESULTS: Results showed no statistically significant difference in tested properties with octacalcium phosphate addition in any concentration. CONCLUSION: OCP addition to GIC did not influence materials properties.

Effect of disinfection techniques on physical-mechanical properties of a microwave-activated acrylic resin

Abstract: The effects of disinfection by microwave irradiation and immersion in peracetic acid on the physical-mechanical properties of a microwave-activated acrylic resin were evaluated. Specimens of acrylic resin were divided into a control group (specimens not disinfected) and 2 test groups subjected to one disinfection method: microwave irradiation at 850 W for 1 minute or immersion in 50 mL of 0.2% peracetic acid for 5 minutes. Specimens were submitted to Knoop hardness, flexural strength, flexural modulus, Izod impact, water sorption and solubility, glass transition temperature, and degree of conversion tests. Microwave disinfection significantly increased the mean Knoop hardness, Izod impact strength, water sorption, water solubility and glass transition temperature, whereas the flexural properties remained unaffected. Microwave disinfection increased the degree of conversion. Peracetic acid disinfection showed no changes in any properties. Both disinfection techniques did not adversely affect the evaluated properties.

Performance of progressive and constant tapered instruments rotary systems at canal preparation

Abstract: Objective: The aim of this study was to compare the performance of two nickel-titanium rotary systems regarding the preparation time, final shape of canal, incidence of aberration, transportation, and fracture of instrument. Methods: A total of 40 simulated canals in resin blocks with 30o curves and a length of 17 mm were divided randomly into two groups: preparation with ProTaper and BioRaCe systems up to F5 and BR5 respectively. Pre- and post-operative canal images were taken and superimposed in order to identify aberrations, transportation, and to take measurements of the canal width. In addition, the preparation time and instrument fractures were recorded. The data were analyzed using Student's t test. Results: There is no difference (p>.05) comparing the systems regarding preparation time, canal aberration, and instrument fracture rates. The progressive tapered instruments of ProTaper prepared significantly larger canal widths in the apical third (p<.05). Conclusion: Overall, both systems provided safe canal preparation, associated with few canal aberrations and instrument fractures.