Deposits of clastic carbonate-dominated (calciclastic) sedimentary slope systems in the rock record have been identified mostly as linearly-consistent carbonate apron deposits, even though most ancient clastic carbonate slope deposits fit the submarine fan systems better. Calciclastic submarine fans are consequently rarely described and are poorly understood. Subsequently, very little is known especially in mud-dominated calciclastic submarine fan systems. Presented in this study are a sedimentological core and petrographic characterisation of samples from eleven boreholes from the Lower Carboniferous of Bowland Basin (Northwest England) that reveals a >250 m thick calciturbidite complex deposited in a calciclastic submarine fan setting. Seven facies are recognised from core and thin section characterisation and are grouped into three carbonate turbidite sequences. They include: 1) Calciturbidites, comprising mostly of highto low-density, wavy-laminated bioclast-rich facies; 2) low-density densite mudstones which are characterised by planar laminated and unlaminated muddominated facies; and 3) Calcidebrites which are muddy or hyper-concentrated debrisflow deposits occurring as poorly-sorted, chaotic, mud-supported floatstones. These

Phd by thesis

In this contribution, we present a new certified world record efficiency of 20.1 and 20.3% for Cu(In,Ga)Se2 thin-film solar cells. We analyse the characteristics of solar cells on such a performance level and demonstrate a high degree of reproducibility. Copyright © 2011 John Wiley & Sons, Ltd.

New world record efficiency for Cu(In,Ga)Se2 thin‐film solar cells beyond 20%

In this study, the Mo-electrode thin films were deposited by a two-stepped process, and the high-purity copper indium selenide-based powder (CuInSe2, CIS) was fabricated by hydrothermal process by Nanowin Technology Co. Ltd. From the X-ray pattern of the CIS precursor, the mainly crystalline phase was CIS, and the almost undetectable CuSe phase was observed. Because the CIS powder was aggregated into micro-scale particles and the average particle sizes were approximately 3 to 8 μm, the CIS power was ground into nano-scale particles, then the 6 wt.% CIS particles were dispersed into isopropyl alcohol to get the solution for spray coating method. Then, 0.1 ml CIS solution was sprayed on the 20 mm × 10 mm Mo/glass substrates, and the heat treatment for the nano-scale CIS solution under various parameters was carried out in a selenization furnace. The annealing temperature was set at 550°C, and the annealing time was changed from 5 to 30 min, without extra Se content was added in the furnace. The influences of annealing time on the densification, crystallization, resistivity (ρ), hall mobility (μ), and carrier concentration of the CIS absorber layers were well investigated in this study.

/pdf/prepare-dispersed-cis-nano-scale-particles-and-spray-coating-17j5lspjdp.pdf

Prepare dispersed CIS nano-scale particles and spray coating CIS absorber layers using nano-scale precursors

We have reduced the processing temperature of the bulk absorber layer in CH3NH3PbI3−xClx perovskite solar cells from 500 to <150 °C and achieved power conversion efficiencies up to 12.3%. Remarkably, we find that devices with planar thin-film architecture, where the ambipolar perovskite transports both holes and electrons, convert the absorbed photons into collected charge with close to 100% efficiency.

Low-temperature processed meso-superstructured to thin-film perovskite solar cells

Organic solar cells are promising for technological applications, as they are lightweight and mechanically robust. This study presents flexible organic solar cells that are less than 2 μm thick, have very low specific weight and maintain their photovoltaic performance under repeated mechanical deformation.

/pdf/ultrathin-and-lightweight-organic-solar-cells-with-high-4rp3u0tfpt.pdf

Ultrathin and lightweight organic solar cells with high flexibility

Solar cells based on polycrystalline Cu(In,Ga)Se(2) absorber layers have yielded the highest conversion efficiency among all thin-film technologies, and the use of flexible polymer films as substrates offers several advantages in lowering manufacturing costs. However, given that conversion efficiency is crucial for cost-competitiveness, it is necessary to develop devices on flexible substrates that perform as well as those obtained on rigid substrates. Such comparable performance has not previously been achieved, primarily because polymer films require much lower substrate temperatures during absorber deposition, generally resulting in much lower efficiencies. Here we identify a strong composition gradient in the absorber layer as the main reason for inferior performance and show that, by adjusting it appropriately, very high efficiencies can be obtained. This implies that future manufacturing of highly efficient flexible solar cells could lower the cost of solar electricity and thus become a significant branch of the photovoltaic industry.

Highly efficient Cu(In,Ga)Se2 solar cells grown on flexible polymer films

Cu(In,Ga)Se2 (CIGS) absorber layers for thin-film solar cells were grown without sodium. Na was diffused into some of the absorbers after growth, which led to strongly improved device performance compared with Na-free cells. Efficiencies of 13.3% and 14.4% were achieved at substrate temperatures as low as 400 and 450 °C, respectively. With the post-deposition treatment, the effects of Na on CIGS growth are excluded, and most of the Na is expected to reside at grain boundaries. The dominating cause for Na-induced device improvements might be passivation of grain boundaries.

Efficiency enhancement of Cu(In,Ga)Se2 solar cells due to post-deposition Na incorporation

Effects of NaF coevaporation on structural properties of Cu(In, Ga)Se2 thin films

Influence of sodium on the growth of polycrystalline Cu(In,Ga)Se2 thin films

We report on the progress that we have made in the quality of our baseline process for the production of high efficiency soda lime glass/Mo/Cu(In,Ga)Se2 (CIGS)/CdS/i-ZnO/ZnO:Al/MgF2 solar cells. The enhancement of the average performance level has enabled us to reach conversion efficiencies of up to 19·3% (internal measurement). The new quality initiative uses process control, optical and electrical modelling, and the critical revision of all process steps as tools for the attainment of the 19% efficiency level. Our experiments show that the compositional process window for CIGS solar cells that have an efficiency of η ≈ 19% is very wide. Accordingly, we suggest that an efficiency of 19·0–19·5% is achievable in the following compositional process windows: 0·69 ≤ Cu/(Ga + In) ≤ 0·98 and 0·21 ≤ Ga/(Ga + In) ≤ 0·38. In addition, our results show that large CIGS grains are not a necessary requirement for high efficiencies up to 19%. These findings and the partly lacking ability to correlate certain aspects of our progress with experimental parameters lead us to the conclusion that there are still some important process variables undiscovered. From this conclusion and from the evaluation of the available data we infer that there is a potential for the enhancement of CIGS solar cell efficiencies beyond 20%. Copyright © 2007 John Wiley & Sons, Ltd.

G. Bilger

Papers

Highly efficient Cu(In,Ga)Se2 solar cells grown on flexible polymer films

Efficiency enhancement of Cu(In,Ga)Se2 solar cells due to post-deposition Na incorporation

Effects of NaF coevaporation on structural properties of Cu(In, Ga)Se2 thin films

Influence of sodium on the growth of polycrystalline Cu(In,Ga)Se2 thin films

High quality baseline for high efficiency, Cu(In1- x,Gax)Se2 solar cells