[신간의 별자리x] 우리/미술, 그리고 ‘슬픔의 박물관’

DC–DC converters with voltage boost capability are widely used in a large number of power conversion applications, from fraction-of-volt to tens of thousands of volts at power levels from milliwatts to megawatts. The literature has reported on various voltage-boosting techniques, in which fundamental energy storing elements (inductors and capacitors) and/or transformers in conjunction with switch(es) and diode(s) are utilized in the circuit. These techniques include switched capacitor (charge pump), voltage multiplier, switched inductor/voltage lift, magnetic coupling, and multistage/-level, and each has its own merits and demerits depending on application, in terms of cost, complexity, power density, reliability, and efficiency. To meet the growing demand for such applications, new power converter topologies that use the above voltage-boosting techniques, as well as some active and passive components, are continuously being proposed. The permutations and combinations of the various voltage-boosting techniques with additional components in a circuit allow for numerous new topologies and configurations, which are often confusing and difficult to follow. Therefore, to present a clear picture on the general law and framework of the development of next-generation step-up dc–dc converters, this paper aims to comprehensively review and classify various step-up dc–dc converters based on their characteristics and voltage-boosting techniques. In addition, the advantages and disadvantages of these voltage-boosting techniques and associated converters are discussed in detail. Finally, broad applications of dc–dc converters are presented and summarized with comparative study of different voltage-boosting techniques.

/pdf/step-up-dc-dc-converters-a-comprehensive-review-of-voltage-6dlytctzg2.pdf

Step-Up DC–DC Converters: A Comprehensive Review of Voltage-Boosting Techniques, Topologies, and Applications

Photovoltaic (PV) energy has grown at an average annual rate of 60% in the last five years, surpassing one third of the cumulative wind energy installed capacity, and is quickly becoming an important part of the energy mix in some regions and power systems. This has been driven by a reduction in the cost of PV modules. This growth has also triggered the evolution of classic PV power converters from conventional singlephase grid-tied inverters to more complex topologies to increase efficiency, power extraction from the modules, and reliability without impacting the cost. This article presents an overview of the existing PV energy conversion systems, addressing the system configuration of different PV plants and the PV converter topologies that have found practical applications for grid-connected systems. In addition, the recent research and emerging PV converter technology are discussed, highlighting their possible advantages compared with the present technology. Solar PV energy conversion systems have had a huge growth from an accumulative total power equal to approximately 1.2 GW in 1992 to 136 GW in 2013 (36 GW during 2013) [1]. This phenomenon has been possible because of several factors all working together to push the PV energy to cope with one important position today (and potentially a fundamental position in the near future). Among these factors are the cost reduction and increase in efficiency of the PV modules, the search for alternative clean energy sources (not based on fossil fuels), increased environmental awareness, and favorable political regulations from local governments (establishing feed-in tariffs designed to accelerate investment in renewable energy technologies). It has become usual to see PV systems installed on the roofs of houses or PV farms next to the roads in the countryside. Grid-connected PV systems account for more than 99% of the PV installed capacity compared to

An Overview of Recent Research and Emerging PV Converter Technology

Photovoltaic (PV) energy has grown at an average annual rate of 60% in the last five years, surpassing one third of the cumulative wind energy installed capacity, and is quickly becoming an important part of the energy mix in some regions and power systems. This has been driven by a reduction in the cost of PV modules. This growth has also triggered the evolution of classic PV power converters from conventional single-phase grid-tied inverters to more complex topologies to increase efficiency, power extraction from the modules, and reliability without impacting the cost. This article presents an overview of the existing PV energy conversion systems, addressing the system configuration of different PV plants and the PV converter topologies that have found practical applications for grid-connected systems. In addition, the recent research and emerging PV converter technology are discussed, highlighting their possible advantages compared with the present technology.

Grid-Connected Photovoltaic Systems: An Overview of Recent Research and Emerging PV Converter Technology

Single-phase voltage source transformerless inverters have been developed for many years and have been successful commercial applications in the distributed photovoltaic (PV) grid-connected systems. Moreover, many advanced industrial topologies and recent innovations have been published in the last few years. The objective of this paper is to classify and review these recent contributions to establish the present state of the art and trends of the transformerless inverters. This can provide a comprehensive and insightful overview of this technology. First, the generation mechanism of leakage current is investigated to divide the transformerless inverters into asymmetrical inductor-based and symmetrical inductor-based groups. Then, the concepts of dc-based and ac-based decoupling networks are proposed to not only cover the published symmetrical inductor-based topologies but also offer an innovative strategy to derive advanced inverters. Furthermore, the transformation principle between the dc-based and ac-based topologies is explored to make a clear picture on the general law and framework for the recent advances and future trend in this area. Finally, a family of clamped highly efficient and reliable inverter concept transformerless inverters is derived and tested to offer some excellent candidates for next-generation high-efficiency and cost-effective PV grid-tie inverters.

Topology Review and Derivation Methodology of Single-Phase Transformerless Photovoltaic Inverters for Leakage Current Suppression

High-step-up, high-efficiency, and cost-effective dc–dc converters, serving as an interfacing cell to boost the low-voltage output of renewable sources to the utility voltage level, are an important part in renewable energy systems. Over the past few years, there has been a substantial amount of studies devoted to high-step-up dc–dc converters. Among them, the category of coupled-inductor boost converters is widely researched and considered to be a promising solution for high-step-up applications. In this paper, these converters are categorized into five groups according to the major topological features. The derivation process, advantages, and disadvantages of these converters are systematically discussed, compared, and scrutinized. This paper aims to provide an introduction, review, and framework for the category of high-step-up coupled-inductor boost converters. General structures for the topologies are proposed to clarify the topological derivation process and to show potential gaps. Furthermore, challenges or directions are presented in this paper for deriving new topologies in this field.

Overview of High-Step-Up Coupled-Inductor Boost Converters

Transformerless inverter topologies have attracted more attentions in photovoltaic (PV) generation system since they feature high efficiency and low cost. In order to meet the safety requirement for transformerless grid-tied PV inverters, the leakage current has to be tackled carefully. Neutral point clamped (NPC) topology is an effective way to eliminate the leakage current. In this paper, two types of basic switching cells, the positive neutral point clamped cell and the negative neutral point clamped cell, are proposed to build NPC topologies, with a systematic method of topology generation given. A family of single-phase transformerless full-bridge topologies with low-leakage current for PV grid-tied NPC inverters is derived including the existing oH5 and some new topologies. A novel positive-negative NPC (PN-NPC) topology is analyzed in detail with operational modes and modulation strategy given. The power losses are compared among the oH5, the full-bridge inverter with dc bypass (FB-DCBP) topology, and the proposed PN-NPC topologies. A universal prototype for these three NPC-type topologies mentioned is built to evaluate the topologies at conversion efficiency and the leakage current characteristic. The PN-NPC topology proposed exhibits similar leakage current with the FB-DCBP, which is lower than that of the oH5 topology, and features higher efficiency than both the oH5 and the FB-DCBP topologies.

/pdf/a-family-of-neutral-point-clamped-full-bridge-topologies-for-46qi9b3vmw.pdf

A Family of Neutral Point Clamped Full-Bridge Topologies for Transformerless Photovoltaic Grid-Tied Inverters

A systematic approach is proposed for the derivation of nonisolated three-port converter (TPC) topologies based on dual-input converters (DIC) and dual-output converters (DOC), which serves as an interface for a renewable source, a storage battery, and a load simultaneously. The power flow in a TPC is analyzed and compared with that in a DIC or a DOC, respectively. Beginning with building the power flow paths of a TPC from a DIC or a DOC, the general principles and detailed procedures for the generation and optimization of TPC topologies are presented. Based on these works, a family of nonisolated TPC topologies is developed. The derived TPCs feature single-stage power conversion between any two of the three ports, and result in high integration and high efficiency. One of the proposed TPCs, named Boost-TPC, is taken as an example for verifying the performance of its circuit topology with related operational methods. Pulsewidth modulation and power management methods, used in this circuit, are analyzed in detail. Experiments have been carried out on a 1-kW prototype of the Boost-TPC, which demonstrate the feasibility and effectiveness of the proposed topology derivation method.

Topology Derivation of Nonisolated Three-Port DC–DC Converters From DIC and DOC

A systematic method for deriving multiport converters (MPCs) from the full bridge (FB) converter (FBC) and bidirectional dc-dc converters (BDCs) is proposed in this paper through sharing the parasitized switching legs by the BDCs and the FBC. By employing the proposed method, families of FB and BDC-based MPCs (FB-BDC-MPCs), including some existing ones, are developed for renewable generation systems with the merits of simple topology, reduced devices, and single-stage power conversion. Voltage regulations between any two ports can be achieved by employing pulsewidth modulation and phase-angle-shift control scheme. Furthermore, zero-voltage switching for all the switches can be realized in the proposed FB-BDC-MPCs. A typical four-port converter developed by the proposed method, named buck/boost four-port converter (BB-FPC), is analyzed in detail as an example in terms of operation principles, design considerations, and control strategy. Experiments have been carried out on a 500-W prototype of BB-FPC, which demonstrate the feasibility and effectiveness of the proposed topology derivation method.

Multiport Converters Based on Integration of Full-Bridge and Bidirectional DC–DC Topologies for Renewable Generation Systems

A systematic method to generate three-port half-bridge converters (TPHBCs) interfacing a renewable source, a storage battery, and a load is proposed for a stand-alone renewable power system application. Allowing dc bias current in the transformer, the primary circuit of a half-bridge converter can function as a synchronous rectification buck converter, by which a power flow path can be configured between the renewable source and the battery, which is connected in parallel with one of the dividing capacitor. To make the voltage on any two of the three ports independently regulated, a postregulation and a synchronous regulation with various implementations are proposed. As a result, a family of TPHBCs with merits of simple topologies and control, reduced number of devices, and single-stage power conversion between any two of the three ports is presented. A TPHBC with a synchronous regulation is given as an example to verify the proposed approach and experimental results are also given to validate the TPHBC operation. The topology generation idea is further extended and some novel TPCs are derived for different applications.

Hongfei Wu

Papers

Overview of High-Step-Up Coupled-Inductor Boost Converters

A Family of Neutral Point Clamped Full-Bridge Topologies for Transformerless Photovoltaic Grid-Tied Inverters

Topology Derivation of Nonisolated Three-Port DC–DC Converters From DIC and DOC

Multiport Converters Based on Integration of Full-Bridge and Bidirectional DC–DC Topologies for Renewable Generation Systems

A Family of Three-Port Half-Bridge Converters for a Stand-Alone Renewable Power System