Solid-state switch-mode rectification converters have reached a matured level for improving power quality in terms of power-factor correction (PFC), reduced total harmonic distortion at input AC mains and precisely regulated DC output in buck, boost, buck-boost and multilevel modes with unidirectional and bidirectional power flow. This paper deals with a comprehensive review of improved power quality converters (IPQCs) configurations, control approaches, design features, selection of components, other related considerations, and their suitability and selection for specific applications. It is targeted to provide a wide spectrum on the status of IPQC technology to researchers, designers and application engineers working on switched-mode AC-DC converters. A classified list of more than 450 research publications on the state of art of IPQC is also given for a quick reference.

/pdf/a-review-of-single-phase-improved-power-quality-ac-dc-2pm6h4zjxq.pdf

A review of single-phase improved power quality AC-DC converters

High-frequency-link (HFL) power conversion systems (PCSs) are attracting more and more attentions in academia and industry for high power density, reduced weight, and low noise without compromising efficiency, cost, and reliability. In HFL PCSs, dual-active-bridge (DAB) isolated bidirectional dc-dc converter (IBDC) serves as the core circuit. This paper gives an overview of DAB-IBDC for HFL PCSs. First, the research necessity and development history are introduced. Second, the research subjects about basic characterization, control strategy, soft-switching solution and variant, as well as hardware design and optimization are reviewed and analyzed. On this basis, several typical application schemes of DAB-IBDC for HPL PCSs are presented in a worldwide scope. Finally, design recommendations and future trends are presented. As the core circuit of HFL PCSs, DAB-IBDC has wide prospects. The large-scale practical application of DAB-IBDC for HFL PCSs is expected with the recent advances in solid-state semiconductors, magnetic and capacitive materials, and microelectronic technologies.

Overview of Dual-Active-Bridge Isolated Bidirectional DC–DC Converter for High-Frequency-Link Power-Conversion System

DC–DC converters with voltage boost capability are widely used in a large number of power conversion applications, from fraction-of-volt to tens of thousands of volts at power levels from milliwatts to megawatts. The literature has reported on various voltage-boosting techniques, in which fundamental energy storing elements (inductors and capacitors) and/or transformers in conjunction with switch(es) and diode(s) are utilized in the circuit. These techniques include switched capacitor (charge pump), voltage multiplier, switched inductor/voltage lift, magnetic coupling, and multistage/-level, and each has its own merits and demerits depending on application, in terms of cost, complexity, power density, reliability, and efficiency. To meet the growing demand for such applications, new power converter topologies that use the above voltage-boosting techniques, as well as some active and passive components, are continuously being proposed. The permutations and combinations of the various voltage-boosting techniques with additional components in a circuit allow for numerous new topologies and configurations, which are often confusing and difficult to follow. Therefore, to present a clear picture on the general law and framework of the development of next-generation step-up dc–dc converters, this paper aims to comprehensively review and classify various step-up dc–dc converters based on their characteristics and voltage-boosting techniques. In addition, the advantages and disadvantages of these voltage-boosting techniques and associated converters are discussed in detail. Finally, broad applications of dc–dc converters are presented and summarized with comparative study of different voltage-boosting techniques.

/pdf/step-up-dc-dc-converters-a-comprehensive-review-of-voltage-6dlytctzg2.pdf

Step-Up DC–DC Converters: A Comprehensive Review of Voltage-Boosting Techniques, Topologies, and Applications

The photovoltaic (PV) grid-connected power system in the residential applications is becoming a fast growing segment in the PV market due to the shortage of the fossil fuel energy and the great environmental pollution. A new research trend in the residential generation system is to employ the PV parallel-connected configuration rather than the series-connected configuration to satisfy the safety requirements and to make full use of the PV generated power. How to achieve high-step-up, low-cost, and high-efficiency dc/dc conversion is the major consideration due to the low PV output voltage with the parallel-connected structure. The limitations of the conventional boost converters in these applications are analyzed. Then, most of the topologies with high-step-up, low-cost, and high-efficiency performance are covered and classified into several categories. The advantages and disadvantages of these converters are discussed. Furthermore, a general conceptual circuit for high-step-up, low-cost, and high-efficiency dc/dc conversion is proposed to derive the next-generation topologies for the PV grid-connected power system. Finally, the major challenges of high-step-up, low-cost, and high-efficiency dc/dc converters are summarized. This paper would like to make a clear picture on the general law and framework for the next-generation nonisolated high-step-up dc/dc converters.

Review of Nonisolated High-Step-Up DC/DC Converters in Photovoltaic Grid-Connected Applications

DC microgrids (MGs) have been gaining a continually increasing interest over the past couple of years both in academia and industry. The advantages of dc distribution when compared to its ac counterpart are well known. The most important ones include higher reliability and efficiency, simpler control and natural interface with renewable energy sources, and electronic loads and energy storage systems. With rapid emergence of these components in modern power systems, the importance of dc in today's society is gradually being brought to a whole new level. A broad class of traditional dc distribution applications, such as traction, telecom, vehicular, and distributed power systems can be classified under dc MG framework and ongoing development, and expansion of the field is largely influenced by concepts used over there. This paper aims first to shed light on the practical design aspects of dc MG technology concerning typical power hardware topologies and their suitability for different emerging smart grid applications. Then, an overview of the state of the art in dc MG protection and grounding is provided. Owing to the fact that there is no zero-current crossing, an arc that appears upon breaking dc current cannot be extinguished naturally, making the protection of dc MGs a challenging problem. In relation with this, a comprehensive overview of protection schemes, which discusses both design of practical protective devices and their integration into overall protection systems, is provided. Closely coupled with protection, conflicting grounding objectives, e.g., minimization of stray current and common-mode voltage, are explained and several practical solutions are presented. Also, standardization efforts for dc systems are addressed. Finally, concluding remarks and important future research directions are pointed out.

/pdf/dc-microgrids-part-ii-a-review-of-power-architectures-69j8nn2rpd.pdf

DC Microgrids—Part II: A Review of Power Architectures, Applications, and Standardization Issues

A bidirectional full-bridge CLLC resonant converter using a new symmetric LLC-type resonant network is proposed for a low-voltage direct current power distribution system. This converter can operate under high power conversion efficiency because the symmetric LLC resonant network has zero-voltage switching capability for primary power switches and soft commutation capability for output rectifiers. In addition, the proposed topology does not require any snubber circuits to reduce the voltage stress of the switching devices because the switch voltage of the primary and secondary power stage is confined by the input and output voltage, respectively. In addition, the power conversion efficiency of any directions is exactly same as each other. Using digital control schemes, a 5-kW prototype converter designed for a high-frequency galvanic isolation of 380-V dc buses was developed with a commercial digital signal processor. Intelligent digital control algorithms are also proposed to regulate output voltage and to control bidirectional power conversions. Using the prototype converter, experimental results were obtained to verify the performance of the proposed topology and control algorithms. The converter could softly change the power flow directions and its maximum power conversion efficiency was 97.8% during the bidirectional operation.

Design Methodology of Bidirectional CLLC Resonant Converter for High-Frequency Isolation of DC Distribution Systems

With the increasing demand for renewable energy, distributed power included in fuel cells have been studied and developed as a future energy source. For this system, a power conversion circuit is necessary to interface the generated power to the utility. In many cases, a high step-up DC/DC converter is needed to boost low input voltage to high voltage output. Conventional methods using cascade DC/DC converters cause extra complexity and higher cost. The conventional topologies to get high output voltage use flyback DC/DC converters. They have the leakage components that cause stress and loss of energy that results in low efficiency. This paper presents a high boost converter with a voltage multiplier and a coupled inductor. The secondary voltage of the coupled inductor is rectified using a voltage multiplier. High boost voltage is obtained with low duty cycle. Theoretical analysis and experimental results verify the proposed solutions using a 300 W prototype.

High boost converter using voltage multiplier

A high-efficiency isolated bidirectional ac–dc converter is proposed for a 380-V dc power distribution system to control bidirectional power flows and to improve its power conversion efficiency. To reduce the switches’ losses of the proposed nonisolated full-bridge ac–dc rectifier using an unipolar switching method, switching devices employ insulated-gate bipolar transistors, MOSFETs, and silicon carbide diodes. Using the analysis of the rectifier’s operating modes, each switching device can be selected by considering switch stresses. A simple and intuitive frequency detection method for a single-phase synchronous reference frame-phase-locked loop (SRF-PLL) is also proposed using a filter compensator, a fast period detector, and a finite impulse response filter to improve the robustness and accuracy of PLL performance under fundamental frequency variations. In addition, design and control methodology of the bidirectional full-bridge CLLC resonant converter is suggested for the galvanic isolation of the dc distribution system. A dead-band control algorithm for the bidirectional dc–dc converter is developed to smoothly change power conversion directions only using output voltage information. Experimental results will verify the performance of the proposed methods using a 5-kW prototype converter.

High-Efficiency Isolated Bidirectional AC–DC Converter for a DC Distribution System

A novel zero-voltage and zero-current-switching (ZVZCS) full-bridge pulsewidth modulation converter is presented to simplify the circuits of the previously presented ZVSCS converters. A simple auxiliary circuit, which consists of one small capacitor and two small diodes, is added in the secondary to provide ZVZCS conditions to primary switches, as well as to clamp secondary rectifier voltage. The additional clamp circuit for the secondary rectifier is not necessary. The auxiliary circuit includes neither lossy components nor additional active switches, which makes the proposed converter efficient and cost effective. The principle of operation, features, and design considerations are illustrated and verified on a 2.5 kW 100 kHz insulated-gate-bipolar-transistor-based experimental circuit.

/pdf/novel-zero-voltage-and-zero-current-switching-full-bridge-qiz45hzaib.pdf

Novel zero-voltage and zero-current-switching full-bridge PWM converter using a simple auxiliary circuit

This paper proposes an effective test bed for a 380-V dc distribution system using isolated power converters. The proposed test-bed system is composed of a grid-interactive ac–dc converter for regulating the dc-bus voltage, a bidirectional converter for the battery power interface, a renewable energy simulator, dc home appliances modified from conventional ac components, a dc distribution panel board, and its monitoring system. This paper discusses three isolated power converters, i.e., a bidirectional ac–dc converter, a bidirectional dc–dc converter, and a unidirectional dc–dc converter for the effective power interface of a dc bus. These isolated power converters are designed using a dual-active-bridge converter and the resonant topologies of $CLLC$ and $LLC$ . The proposed test-bed system was implemented using a 5-kW bidirectional ac–dc prototype converter, a 3-kW bidirectional dc–dc prototype converter, and a 3-kW unidirectional dc–dc prototype converter. Finally, the performance of the test-bed system has been verified using practical experiments of load variations and bidirectional power flow, employing the prototype converters.

Ju-Won Baek

Papers

Design Methodology of Bidirectional CLLC Resonant Converter for High-Frequency Isolation of DC Distribution Systems

High boost converter using voltage multiplier

High-Efficiency Isolated Bidirectional AC–DC Converter for a DC Distribution System

Novel zero-voltage and zero-current-switching full-bridge PWM converter using a simple auxiliary circuit

Effective Test Bed of 380-V DC Distribution System Using Isolated Power Converters