Fast Fourier Transform

Resonance-based wireless power delivery is an efficient technique to transfer power over a relatively long distance. This technique typically uses four coils as opposed to two coils used in conventional inductive links. In the four-coil system, the adverse effects of a low coupling coefficient between primary and secondary coils are compensated by using high-quality (Q) factor coils, and the efficiency of the system is improved. Unlike its two-coil counterpart, the efficiency profile of the power transfer is not a monotonically decreasing function of the operating distance and is less sensitive to changes in the distance between the primary and secondary coils. A four-coil energy transfer system can be optimized to provide maximum efficiency at a given operating distance. We have analyzed the four-coil energy transfer systems and outlined the effect of design parameters on power-transfer efficiency. Design steps to obtain the efficient power-transfer system are presented and a design example is provided. A proof-of-concept prototype system is implemented and confirms the validity of the proposed analysis and design techniques. In the prototype system, for a power-link frequency of 700 kHz and a coil distance range of 10 to 20 mm, using a 22-mm diameter implantable coil resonance-based system shows a power-transfer efficiency of more than 80% with an enhanced operating range compared to ~40% efficiency achieved by a conventional two-coil system.

Design and Optimization of Resonance-Based Efficient Wireless Power Delivery Systems for Biomedical Implants

This paper describes the development of a high-density electronic interface to the central nervous system. Silicon micromachined electrode arrays now permit the long-term monitoring of neural activity in vivo as well as the insertion of electronic signals into neural networks at the cellular level. Efforts to understand and engineer the biology of the implant/tissue interface are also underway. These electrode arrays are facilitating significant advances in our understanding of the nervous system, and merged with on-chip circuitry, signal processing, microfluidics, and wireless interfaces, they are forming the basis for a family of neural prostheses for the possible treatment of disorders such as blindness, deafness, paralysis, severe epilepsy, and Parkinson's disease.

/pdf/wireless-implantable-microsystems-high-density-electronic-2s60s28lz9.pdf

Wireless implantable microsystems: high-density electronic interfaces to the nervous system

The next generation of implantable high-power neuroprosthetic devices such as visual prostheses and brain computer interfaces are going to be powered by transcutaneous inductive power links formed between a pair of printed spiral coils (PSC) that are batch-fabricated using micromachining technology. Optimizing the power efficiency of the wireless link is imperative to minimize the size of the external energy source, heating dissipation in the tissue, and interference with other devices. Previous design methodologies for coils made of 1-D filaments are not comprehensive and accurate enough to consider all geometrical aspects of PSCs with planar 3-D conductors as well as design constraints imposed by implantable device application and fabrication technology. We have outlined the theoretical foundation of optimal power transmission efficiency in an inductive link, and combined it with semi-empirical models to predict parasitic components in PSCs. We have used this foundation to devise an iterative PSC design methodology that starts with a set of realistic design constraints and ends with the optimal PSC pair geometries. We have executed this procedure on two design examples at 1 and 5 MHz achieving power transmission efficiencies of 41.2% and 85.8%, respectively, at 10-mm spacing. All results are verified with simulations using a commercial field solver (HFSS) as well as measurements using PSCs fabricated on printed circuit boards.

Design and Optimization of Printed Spiral Coils for Efficient Transcutaneous Inductive Power Transmission

A simple, physically based analysis illustrate the noise processes in CMOS inverter-based and differential ring oscillators. A time-domain jitter calculation method is used to analyze the effects of white noise, while random VCO modulation most straightforwardly accounts for flicker (1/f) noise. Analysis shows that in differential ring oscillators, white noise in the differential pairs dominates the jitter and phase noise, whereas the phase noise due to flicker noise arises mainly from the tail current control circuit. This is validated by simulation and measurement. Straightforward expressions for period jitter and phase noise enable manual design of a ring oscillator to specifications, and guide the choice between ring and LC oscillator

http://venividiwiki.ee.virginia.edu/mediawiki/images/c/c2/A_abidi.pdf

Phase Noise and Jitter in CMOS Ring Oscillators

Radio-frequency (RF) coils are used extensively in the design of implantable devices for transdermal power and data transmission. The practical issues of coil misalignments and configurations have not been investigated, and this paper presents a detailed theoretical analysis of misalignment effects in RF coil systems, including lateral and angular misalignments. Formulas are derived for the mutual inductance and, whenever possible, simplified upper bounds and lower bounds of the coupling coefficient are provided. A design procedure is established to maximize coil coupling for a given configuration, and a companion paper [1] discusses a circuit design technique to reduce the effects of misalignment on transmission efficiency.

Radio-Frequency Coils in Implantable Devices: Misalignment Analysis and Design Procedure

This paper describes a new method of desensitizing the gain of an inductive link to the mutual coupling of its inductors. When the coupling varies due to geometrical misalignments [1] this design method guarantees good efficiency and a large bandwidth. The mathematics for four link combinations are presented, and examples of the link efficiency and bandwidth for one of the combinations are shown and discussed.

A Wide-Band Efficient Inductive Transdennal Power and Data Link with Coupling Insensitive Gain

A Green's function approach has been used to solve Lapalce's equation for the quasi-static fields of a recessed, disk electrode. The resulting integral equation was solved numerically using the moment method. An analysis of the error in the approximate solution shows that it must be less than 7 percent for the cases studied. The calculations indicate that a recessed electrode has a more uniform current density profile than a surface mounted electrode. This is true both at the electrode surface, and at the electrode carrier?tissue junction. The significance of this finding is discussed as is its application to electrochemical, histopathological, and physiological studies of neural prostheses. The clinical use of recessed electrodes in cochlear implants is recommended.

Current Density Profiles of Surface Mounted and Recessed Electrodes for Neural Prostheses

Static tests are key in reducing the current high cost of testing analog and mixed-signal ICs. A new DC test generation technique for detecting catastrophic failures in this class of circuits is presented. To include the effect of tolerance of parameters during testing, the test generation problem is formulated as a minimax optimization problem, and solved iteratively as successive linear programming problems. An analytical fault modeling technique, based on manufacturing defect statistics is used to derive the fault list for the test generation. Using the technique presented here an efficient static test set for analog and mixed-signal ICs can be constructed, reducing both the test time and the packaging cost.

/pdf/analytical-fault-modeling-and-static-test-generation-for-37r57fl4dt.pdf

Analytical fault modeling and static test generation for analog ICs

A measuring apparatus is provided that includes: a timing jitter calculator for calculating the first timing jitter sequence of the first signal and the second timing jitter sequence of the second signal; and a jitter transfer function estimator for calculating a jitter transfer function between the first and second signals based on frequency components of the first and second timing jitter sequences. The jitter transfer function estimator calculates the jitter transfer function, for a plurality of frequency component pairs each of which is formed by a frequency component of a timing jitter in the first timing jitter sequence and a frequency component of a timing jitter in the second timing jitter sequence which correspond to approximately equal frequencies, based on frequency component ratios of the timing jitters in the first and second timing jitter sequences.

Mani Soma

Papers

Radio-Frequency Coils in Implantable Devices: Misalignment Analysis and Design Procedure

A Wide-Band Efficient Inductive Transdennal Power and Data Link with Coupling Insensitive Gain

Current Density Profiles of Surface Mounted and Recessed Electrodes for Neural Prostheses

Analytical fault modeling and static test generation for analog ICs

Measuring apparatus and measuring method