There is, I think, something ethereal about i —the square root of minus one. I remember first hearing about it at school. It seemed an odd beast at that time—an intruder hovering on the edge of reality.

Usually familiarity dulls this sense of the bizarre, but in the case of i it was the reverse: over the years the sense of its surreal nature intensified. It seemed that it was impossible to write mathematics that described the real world in …

I and i

다중혈관 관상동맥 환자에서 y-문합을 이용하여 양쪽 내흉동맥만을 사용한 우회술의 조기 성적

抗原变异可使得多种致病微生物易于逃避宿主免疫应答。表达在感染红细胞表面的恶性疟原虫红细胞表面蛋白1（PfPMP1）与感染红细胞、内皮细胞、树突状细胞以及胎盘的单个或多个受体作用，在黏附及免疫逃避中起关键的作用。每个单倍体基因组var基因家族编码约60种成员，通过启动转录不同的var基因变异体为抗原变异提供了分子基础。

疟原虫var基因转换速率变化导致抗原变异[英]／Paul H, Robert P, Christodoulou Z, et al//Proc Natl Acad Sci U S A

[신간의 별자리x] 우리/미술, 그리고 ‘슬픔의 박물관’

Deposits of clastic carbonate-dominated (calciclastic) sedimentary slope systems in the rock record have been identified mostly as linearly-consistent carbonate apron deposits, even though most ancient clastic carbonate slope deposits fit the submarine fan systems better. Calciclastic submarine fans are consequently rarely described and are poorly understood. Subsequently, very little is known especially in mud-dominated calciclastic submarine fan systems. Presented in this study are a sedimentological core and petrographic characterisation of samples from eleven boreholes from the Lower Carboniferous of Bowland Basin (Northwest England) that reveals a >250 m thick calciturbidite complex deposited in a calciclastic submarine fan setting. Seven facies are recognised from core and thin section characterisation and are grouped into three carbonate turbidite sequences. They include: 1) Calciturbidites, comprising mostly of highto low-density, wavy-laminated bioclast-rich facies; 2) low-density densite mudstones which are characterised by planar laminated and unlaminated muddominated facies; and 3) Calcidebrites which are muddy or hyper-concentrated debrisflow deposits occurring as poorly-sorted, chaotic, mud-supported floatstones. These

Phd by thesis

When a layer of a semicrystalline polymer is subject to a tensile force in its plane and a voltage through its thickness, the deformation of the layer is initially homogeneous, but it then localizes. The electromechanical instability sets in when the force and the voltage reach critical conditions. The critical conditions are determined in this paper and are related to the following two special cases: the Considere condition for the necking instability and the Stark–Garton condition for the pull-in instability. The general critical conditions show that a tensile force can markedly reduce the critical voltage.

/pdf/electromechanical-instability-in-semicrystalline-polymers-2yyij9bcdb.pdf

Electromechanical instability in semicrystalline polymers

This paper studies the collapse of a void in an elastomer caused by osmosis. The void is filled with liquid water, while the elastomer is surrounded by unsaturated air. The difference in humidity motivates water molecules to permeate through the elastomer, from inside the void to outside the elastomer, leaving the liquid water inside the void in tension. When the tension is low, the void reduces size but retains the shape, a mode of deformation which we call breathing. When the tension is high, the void changes shape, possibly by two types of instability: buckling and creasing. The critical conditions for both types of instability are calculated. A tubular elastomer collapses by buckling if the wall is thin, but by creasing if the wall is thick. As the tension increases, a thin-walled tube undergoes a buckle-to-crease transition.

/pdf/osmotic-collapse-of-a-void-in-an-elastomer-breathing-33fla8j0a5.pdf

Osmotic collapse of a void in an elastomer: breathing, buckling and creasing

In the microelectronic and photonic industries, temperature cycling has long been used as a reliability test to qualify integrated materials structures of small feature sizes. The test is time consuming, and is a bottleneck for innovation. Tremendous needs exist to understand various failure modes in the integrated structures caused by cyclic temperatures. This paper presents a systematic study of a failure mechanism recently discovered by the authors. In a thin film structure comprising both ductile and brittle materials, the thermal expansion mismatch can cause the ductile material to plastically yield in every temperature cycle. Under certain circumstances, the plastic deformation ratchets, namely, accumulates in the same direction as the temperature cycles. The ratcheting deformation in the ductile material may build up stress in the brittle materials, leading to cracking. The paper introduces an analogy between ratcheting and viscous flow. An analytical model is developed, which explains the experimental observations, and allows one to design the structure to avert this failure mode. Design rules with increasing levels of sophistication are described. Concepts presented here are generic to related phenomena in thin film structures.

Plastic ratcheting induced cracks in thin film structures

Hydrogels of numerous chemical compositions have achieved high fracture toughness on the basis of one physical principle. As a crack advances in such a hydrogel, a polymer network of strong bonds r...

Fracture Toughness and Fatigue Threshold of Tough Hydrogels

https://www.ae.utexas.edu/~ruihuang/papers/IJSS02.pdf

Zhigang Suo

Papers

Electromechanical instability in semicrystalline polymers

Osmotic collapse of a void in an elastomer: breathing, buckling and creasing

Plastic ratcheting induced cracks in thin film structures

Fracture Toughness and Fatigue Threshold of Tough Hydrogels

Evolving crack patterns in thin films with the extended finite element method