Advances in Physical Chemistry 

About: Advances in Physical Chemistry is an academic journal. The journal publishes majorly in the area(s): Adsorption & Catalysis. It has an ISSN identifier of 1687-7985. It is also open access. Over the lifetime, 125 publications have been published receiving 1971 citations.

Fundamental mechanistic understanding of electrocatalysis of oxygen reduction on Pt and non-Pt surfaces: Acid versus alkaline media

Abstract: Complex electrochemical reactions such as Oxygen Reduction Reaction (ORR) involving multi-electron transfer is an electrocatalytic inner-sphere electron transfer process that exhibit strong dependence on the nature of the electrode surface. This criterion (along with required stability in acidic electrolytes) has largely limited ORR catalysts to the platinum-based surfaces. New evidence in alkaline media, discussed here, throws light on the involvement of surface-independent outer-sphere electron transfer component in the overall electrocatalytic process. This surface non-specificity gives rise to the possibility of using a wide-range of non-noble metal surfaces as electrode materials for ORR in alkaline media. However, this outer-sphere process predominantly leads only to peroxide intermediate as the final product. The importance of promoting the electrocatalytic inner-sphere electron transfer by facilitation of direct adsorption of molecular oxygen on the active site is emphasized by using pyrolyzed metal porphyrins as electrocatalysts. A comparison of ORR reaction mechanisms between acidic and alkaline conditions is elucidated here. The primary advantage of performing ORR in alkaline media is found to be the enhanced activation of the peroxide intermediate on the active site that enables the complete four-electron transfer. ORR reaction schemes involving both outer- and inner-sphere electron transfer mechanisms are proposed.

(Photo)electrochemical Methods for the Determination of the Band Edge Positions of TiO2-Based Nanomaterials

Abstract: TiO2-based nanomaterials play currently a major role in the development of novel photochemical systems and devices. One of the key parameters determining the photoactivity of TiO2-based materials is the position of the band edges. Although its knowledge is an important prerequisite for understanding and optimizing the performance of photochemical systems, it has been often rather neglected in recent research, particularly in the field of heterogeneous photocatalysis. This paper provides a concise account of main methods for the determination of the position of the band edges, particularly those suitable for measurements on nanostructured materials. In the first part, a survey of key photophysical and photochemical concepts necessary for understanding the energetics at the semiconductor/solution interface is provided. This is followed by a detailed discussion of several electrochemical, photoelectrochemical, and spectroelectrochemical methods that can be applied for the determination of band edge positions in compact and nanocrystalline thin films, as well as in nanocrystalline powders.

Infrared Spectroscopy of Anionic, Cationic, and Zwitterionic Surfactants

Abstract: This paper describes the ordering degree of anionic, cationic, and zwitterionic surfactants with the increase of their packing density on Ge substrate by using Fourier transform infrared-attenuated total reflection (FTIR-ATR) spectroscopy. This work shows new insights on the conformational order of sodium dodecyl sulfate (SDS), N-hexadecyl-N-N-dimethyl-3-ammonio-1-propane-sulfonate (HPS), hexadecyl-trimethylammonium bromide (CTAB), and dodecyl trimethylammonium bromide (DTAB). DFT and semiempirical calculations are also performed in order to evaluate the effect of headgroup hydration and counterion. The CH2 asymmetric and symmetric stretching bands for the SDS molecule show a shift of 1.7 and 0.9 cm−1 to higher frequencies as the packing density increases, while it is observed a shift of 2.6 and 2.7 cm−1 for the HPS molecule, respectively. The DTAB molecule shows a shift of 4.5 cm−1 to lower frequencies for both CH2 asymmetric and symmetric stretching bands as the packing density increases, indicating the decrease of gauche conformations and the increase of all-trans conformations over the aliphatic chain.

Superparamagnetic Iron Oxide (Fe3O4) Nanoparticles Coated with PEG/PEI for Biomedical Applications: A Facile and Scalable Preparation Route Based on the Cathodic Electrochemical Deposition Method

Abstract: Cathodic electrochemical deposition (CED) is introduced as an efficient and effective method for synthesis and surface coating of superparamagnetic iron oxide nanoparticles (SPIONs). In this way, bare Fe3O4 nanoparticles were electrosynthesized through CED method from aqueous solution Fe3+ : Fe2+ chloride (molar ratio of 2 : 1). In the next step, the surface of NPs was coated with polyethyleneimine (PEI) and polyethylene glycol (PEG) during the CED procedure, and PEG/PEI coated SPIONs were obtained. The prepared NPs were evaluated by powder X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), dynamic light scattering (DLS), vibrating sample magnetometer (VSM), and field-emission scanning electron microscopy (FE-SEM). The pure magnetite phase and nanosize (about 15 nm) of the prepared NPs were confirmed by XRD and FE-SEM. The presence of two coats (i.e., PEG and PEI) on the surface of electrosynthesized NPs was proved via FTIR results. The percentage of polymer coat (37.5%) on the NPs surface was provided by TGA analysis. The high magnetization value, negligible coercivity, and remanence measured by VSM indicate the superparamagnetic nature of both prepared NPs. The obtained results confirmed that the prepared Fe3O4 nanoparticles have suitable physicochemical and magnetic properties for biomedical applications.

Nanotoxicity: Dimensional and Morphological Concerns

Abstract: Nanotechnology deals with the construction of new materials, devices, and different technological systems with a wide range of potential applications at the atomic and molecular level. Nanomaterials have attracted great attention for numerous applications in chemical, biological, and industrial world because of their fascinating physicochemical properties. Nanomaterials and nanodevices are being produced intentionally, unintentionally, and manufactured or engineered by different methods and released into the environment without any safety test. Nantoxicity has become the subject of concern in nanoscience and nanotechnology because of the increasing toxic effects of nanomaterials on the living organisms. Nanomaterials can move freely as compared to the large-sized particles; therefore, they can be more toxic than bulky materials. This review article delineates the toxic effects of different types of nanomaterials on the living organisms through different sources, like water, air, contact with skin, and the methods of determinations of these toxic effects.