Journal ArticleDOI
Computer-aided manufacturing of spiral bevel and hypoid gears with minimum surface-deviation
Reads0
Chats0
TLDR
In this article, a linear regression method to minimize the deviations of a real cut gear-tooth surface is investigated, based on the Gleason hypoid gear generator, a mathematical model of the tooth surface is proposed.About:
This article is published in Mechanism and Machine Theory.The article was published on 1998-08-01. It has received 70 citations till now. The article focuses on the topics: Tooth surface & Spiral bevel gear.read more
Citations
More filters
Journal ArticleDOI
Optimization of the Loaded Contact Pattern in Hypoid Gears by Automatic Topography Modification
TL;DR: In this paper, a fully automatic procedure was proposed to optimize the loaded tooth contact pattern under load, with the advantage of eventually reducing design time and cost, and the results obtained were very satisfactory in terms of accuracy, robustness, and computational speed.
Journal ArticleDOI
Flank Modification Methodology for Face-Hobbing Hypoid Gears Based on Ease-Off Topography
Yi-Pei Shih,Zhang-Hua Fong +1 more
TL;DR: In this paper, the authors proposed a flank modification methodology for face-hobbing spiral bevel and hypoid gears based on the ease-off topography of the gear drive.
Journal ArticleDOI
Nonlinear identification of machine settings for flank form modifications in hypoid gears
TL;DR: In this article, the Levenberg-Marquardt method with a trust region strategy is used to identify the values of the machine-tool settings required to obtain flank form modifications in hypoid gears.
Journal ArticleDOI
Computer simulation of tooth contact analysis of mismatched spiral bevel gears
TL;DR: In this article, a new method for computer aided tooth contact analysis in mismatched spiral bevel gears is presented, based on the minimization of the function that determines these separations, defined as the distances of corresponding surface points that are the intersection-points of the straight line parallel to the common surface normal in the instantaneous theoretical contact point with the pinion and gear tooth surfaces.
Journal ArticleDOI
Fourth-order kinematic synthesis for face-milling spiral bevel gears with modified radial motion (MRM) correction
Pei-Yu Wang,Zhang-Hua Fong +1 more
TL;DR: In this article, a modified radial motion (MRM) correction in the machine plane of a computer numerical control (CNC) hypoid generator is introduced to modify the pinion tooth surface.
References
More filters
Numerical recipes in C
TL;DR: The Diskette v 2.06, 3.5''[1.44M] for IBM PC, PS/2 and compatibles [DOS] Reference Record created on 2004-09-07, modified on 2016-08-08.
Book
Theory of Gearing
TL;DR: In this article, basic mathematical problems on the theory of gearing are covered in this book, such as the necessary and sufficient conditions of envelope existence, relations between principal curvatures and directions for surfaces of mating gears.
Journal ArticleDOI
Methods of Synthesis and Analysis for Hypoid Gear-Drives of “Formate” and “Helixform”—Part 1. Calculations For Machine Settings For Member Gear Manufacture of the Formate and Helixform Hypoid Gears
Faydor L. Litvin,Y. Gutman +1 more
Journal ArticleDOI
Surface Geometry of Straight and Spiral Bevel Gears
Ying-Chien Tsai,P. C. Chin +1 more
TL;DR: In this article, the parametric representations of the spherical involute and the involute spiraloid, which are the tooth surface geometry of straight bevel and spiral bevels, respectively, have been derived.
Journal ArticleDOI
Minimization of Deviations of Gear Real Tooth Surfaces Determined by Coordinate Measurements
TL;DR: The approach developed in this paper enables the determi-nation of deviations of a real surface from the known theoreticalsurface and is less effective as compared to computerizeddetermination of surface deviations and corrections of machine-tool settings.