Journal ArticleDOI
Effects of microstructural evolution on the corrosion properties of AISI 420 martensitic stainless steel during cold rolling process
TLDR
In this article, the impacts of plastic deformation induced by compressive stresses on the evolution of the microstructure and the resultant corrosion properties of AISI 420 martensitic stainless steel (MSS) are investigated.About:
This article is published in Materials Chemistry and Physics.The article was published on 2021-01-15. It has received 24 citations till now. The article focuses on the topics: Pitting corrosion & Martensitic stainless steel.read more
Citations
More filters
Journal ArticleDOI
Additive manufacturing of novel ferritic stainless steel by selective laser melting: Role of laser scanning speed on the formability, microstructure and properties
TL;DR: In this article, the effect of laser scanning speed on the formability, microstructural evolution, wear and corrosion performance of selective laser melting (SLM) novel stainless steel was investigated.
Journal ArticleDOI
On microstructure, crystallographic orientation, and corrosion properties of wire arc additive manufactured 420 martensitic stainless steel: Effect of the inter-layer temperature
TL;DR: In this article, the effects of inter-layer temperature variation on the microstructure, crystallographic orientation, and corrosion performance of a multilayer single-pass wall-shaped 420 stainless steel part fabricated using wire arc additive manufacturing (WAAM) were investigated.
Journal ArticleDOI
Effects of (Ti, Mo) C particles on the abrasive wear -corrosion of low alloy martensitic steel
TL;DR: In this paper , the influence of (Ti, Mo) C particles on the abrasive wear-corrosion resistance of low alloy martensitic steel was investigated, and the results indicated that owing to the hindrance of carbides on abrasive microploughing, the abrasives wear resistance of these materials was strengthened by increasing carbide content.
Journal ArticleDOI
Effect of Uniaxial Tension-Induced Plastic Strain on the Microstructure and Corrosion Behavior of 13Cr Martensitic Stainless Steel
TL;DR: In this article, the correlation between the manufacturing process-induced plastic deformation, microstructure, and corrosion behavior of a 13Cr martensitic stainless-steel tubing was investigated.
Journal ArticleDOI
Effects of Secondary-Phase Formation on the Electrochemical Performance of a Wire Arc Additive Manufactured 420 Martensitic Stainless Steel under Different Heat Treatment Conditions.
TL;DR: In this article, the effects of annealing, quenching, and tempering (Q&T) heat treatments on the microstructure, crystallographic orientation, and electrochemical performance of a wall shaped 420 martensitic stainless steel part fabricated by wire arc additive manufacturing technology were investigated.
References
More filters
Book
Electrochemistry at Semiconductor and Oxidized Metal Electrodes
TL;DR: In this paper, the authors present a theoretical analysis of the energy levels at the surface of a delectable deformed deformed metal deformed by Mott-Schottky Plots.
Journal ArticleDOI
The Point Defect Model for the Passive State
TL;DR: In this paper, a review is presented of the point defect model for the growth and breakdown of passive films on metal and alloy surfaces in contact with aqueous solutions, and the model provides a reasonable account of the steady-state properties of cation-conducting and anionconducting barrier layers on nickel and tungsten, respectively, in phosphate buffer solutions.
Journal ArticleDOI
Passive films on stainless steels—chemistry, structure and growth
C.-O. A. Olsson,D. Landolt +1 more
TL;DR: In this paper, the authors reviewed progress in the characterisation and understanding of passive films on stainless steels achieved over the past two decades, and showed that at short times, charge transfer at the metal/film or the film/solution interface limits the rate of film growth.
Journal ArticleDOI
Optimization of grain boundary character distribution for intergranular corrosion resistant 304 stainless steel by twin-induced grain boundary engineering
TL;DR: In this paper, the effects of process parameters, pre-strain, annealing temperature, etc. on grain boundary character distribution and intergranular corrosion in thermomechanical treatment were examined during grain boundary engineering of type 304 austenitic stainless steel.
Journal ArticleDOI
The electronic structure of passive films formed on stainless steels
TL;DR: In this article, the capacitance behavior of passive films formed on austenitic type 304 stainless steel and Fe-Cr alloys (0 ≤ Cr ≤ 30%) was studied using the Mott-Schottky approach.
Related Papers (5)
The effect of TiN inclusions and deformation-induced martensite on the corrosion properties of AISI 321 stainless steel
Mirjam Bajt Leban,Robert Tisu +1 more
Effect of deformation-induced phase transformation on AISI 316 stainless steel corrosion resistance
Nicolae Solomon,Iulia Solomon +1 more