Journal ArticleDOI
Texture and earing behaviour of cold-rolled aluminium alloy 3004
Reads0
Chats0
TLDR
In this article, the effect of cold rolling and annealing on the earing behavior of aluminium alloy 3004 was investigated by X-ray diffraction and it was observed that an increase in the difference between the (422 and (200) Xray intensities in the rolling plane is correlated with 45° earing.About:
This article is published in Materials Science and Engineering.The article was published on 1985-10-01. It has received 12 citations till now. The article focuses on the topics: Earing & Aluminium alloy.read more
Citations
More filters
Journal ArticleDOI
Effect of deformation condition on plastic anisotropy of as-rolled 7050 aluminum alloy plate
Wang Xinyun,H.E. Hu,Xia Ju-chen +2 more
TL;DR: In this paper, the plastic anisotropy of the as-rolled 7050 aluminum alloy plate was investigated by tensile tests conducted at different temperatures (340 and 460°C) and different strain rates of 1.0, 1.1, and 1.s −1.
Journal ArticleDOI
Analytical derivation of earing in circular cup drawing based on simple tension properties
TL;DR: In this article, a simplified analytical derivation of earing development in circular cylindrical cup drawing is proposed, based on two simple tension anisotropic properties: the yield stress and the r-value.
Journal ArticleDOI
Analysis of the earing behaviour of aluminium 3004 alloys by means of a single model based on yield loci calculated from orientation distribution functions
TL;DR: In this paper, the influence of texture on earing behavior of industrially processed 3004-type aluminium alloy sheets was studied, and a simple model for the prediction of earing was proposed, which is only suitable for the cases studied, i.e. for sheets that developed four ears in a cup test.
Journal ArticleDOI
Annealing response of 3000 and 5000 series aluminum alloys
H. D. Merchant,James G. Morris +1 more
TL;DR: In this article, the earing transition upon annealing has been found to be considerably easier for the 5000 than for the 3000 series alloys, that is, easier in the absence of Mn.
References
More filters
Journal ArticleDOI
A Direct Method of Determining Preferred Orientation of a Flat Reflection Sample Using a Geiger Counter X-Ray Spectrometer
TL;DR: In this article, a new reflection method is described for determining pole figures of flat samples with a Geiger counter x-ray spectrometer, which can be used directly without corrections for changes in geometry during rotation of the sample.
Journal ArticleDOI
Texture and earing in deep drawing of aluminium
TL;DR: In this paper, a simple theoretical approach using the maximum resolved shear stress criterion for slip on {111} 〈110〉 systems is described which enables all the important features of the earing of cups pressed from single crystals to be predicted.
Journal ArticleDOI
Influence of hot-working parameters on earing behaviour of Al–2Mg sheet
T. Sheppard,M. A. Zaidi +1 more
TL;DR: In this paper, a linear relationship exists between hot-work induced subgrain size and percentage earing for material which has been (i) hot, (ii) hot rolled and cold rolled, (iii) hot and annealed, (iv) hot-rolled, annealing, and cold-rolled.
Journal ArticleDOI
Earing in Deep-Drawing Steels
TL;DR: In this article, the variations of the fourth-order coefficients of the crystallite orientation distribution function with rolling reduction have been determined after cold-rolling and annealing for a deep-drawing quality rimming steel and an aluminium-killed steel.
Related Papers (5)
Comparison of earing behavior between continuous cast and direct chill cast AA 5182 aluminum alloys during cold rolling and annealing
Control of Earing in Deep Drawing of Roll-Cast AA3003 Aluminium Sheets
Reza Mahmudi,M.M. Alaiha +1 more