Institution
Rolls-Royce Holdings
Company•Derby, United Kingdom•
About: Rolls-Royce Holdings is a company organization based out in Derby, United Kingdom. It is known for research contribution in the topics: Turbine & Gas compressor. The organization has 4027 authors who have published 6305 publications receiving 80517 citations. The organization is also known as: Rolls-Royce Holdings plc.
Topics: Turbine, Gas compressor, Rotor (electric), Turbine blade, Casing
Papers published on a yearly basis
Papers
More filters
••
TL;DR: In this article, the effect of minor additions (C and Hf) on the morphology of MC carbides in SX superalloys RR2072 and RR2086 has been investigated.
51 citations
••
01 Jan 2006TL;DR: In this paper, the authors investigated a circular cooling passage with tangential injection suitable for a blade leading edge, and measured the heat transfer coefficients using the conventional transient heat transfer, liquid crystal technique.
Abstract: In certain regions of turbine aerofoils, cooling system designers need to cool the blades with convection systems that provide high heat transfer coefficients. The present research has investigated a circular cooling passage with tangential injection suitable for a blade leading edge. The heat transfer coefficients are measured using the conventional transient heat transfer, liquid crystal technique. The results are compared to the data from steady state experiments performed by Hedlund et al. [1]. The cooling system performance is compared in detail to average data from earlier tangential injection experiments and to local heat transfer coefficient expected from a normal impingement system. The vortex flow field was also studied by numerical prediction and near-wall velocity measurements. The investigation of the flow structure has led to understanding of flow mechanisms responsible for the high heat transfer coefficient. The vortex flow field was also investigated using computational fluid dynamics and with hot wire anemometry. The latter near wall measurements were combined with the law of the wall and Colburn analogy to validate the flow and heat transfer measurements.© 2006 ASME
51 citations
••
TL;DR: In this article, a numerical simulation of the performance of an idealized wave-plate mist eliminator is used to assess the influence of drainage channels in the mist elimination passages, and the effect of the drainage channels on the primary gas flow and on the evolution of the liquid droplet distribution is calculated for a range of gas speeds, waveplate spacing, channel sizes and inlet droplet size distributions.
Abstract: Numerical simulation of the performance of an idealized wave-plate mist eliminator is used to assess the influence of drainage channels in the mist eliminator passages. The effect of the drainage channels on the primary gas flow and on the evolution of the liquid droplet distribution is calculated for a range of gas speeds, wave-plate spacing, channel sizes and inlet droplet size distributions. The ability of drainage channels to increase the droplet collection efficiency is confirmed and several features of the flow are predicted which have implications for the design of wave-plate mist eliminators.
51 citations
••
TL;DR: In this paper, single crystal seeds of the nickel-base superalloy CMSX-4 have been partially melted in a temperature gradient and then quenched, and small islands of random orientation are observed throughout the melted-back semi-solid.
51 citations
•
14 May 2003TL;DR: In this paper, a computer-implemented method of generating an inspection program for a computer controlled coordinate measuring probe is described, which includes the steps of: (a) receiving nominal geometry data for a component, (b) receiving inspection requirement data specifying one or more selected shape characteristics of the component, and (c) determining from the nominal geometrical data and the inspection requirements data an inspection path for the computer-controlled measuring probe, the inspection path enabling the measuring probe to measure actual component coordinates associated with the selected shapes.
Abstract: A computer-implemented method of generating an inspection program for a computer-controlled coordinate measuring probe comprises the steps of: (a) receiving nominal geometry data for a component, (b) receiving inspection requirement data specifying one or more selected shape characteristics of the component, (c) determining from the nominal geometry data and the inspection requirement data an inspection path for a computer-controlled coordinate measuring probe, the inspection path enabling the measuring probe to measure actual component coordinates associated with the selected shape characteristics, and (d) generating an inspection program for moving the computer-controlled coordinate measuring probe along the inspection path.
51 citations
Authors
Showing all 4029 results
Name | H-index | Papers | Citations |
---|---|---|---|
David A. Jackson | 136 | 1095 | 68352 |
David Harvey | 115 | 738 | 94678 |
David J. Williams | 107 | 2060 | 62440 |
Michael Walsh | 102 | 963 | 42231 |
Zi-Qiang Zhu | 89 | 1049 | 33963 |
H. K. D. H. Bhadeshia | 77 | 476 | 27588 |
Nigel P. Brandon | 71 | 412 | 18511 |
Sanjib Kumar Panda | 64 | 633 | 13808 |
Fabrizio Scarpa | 63 | 467 | 13559 |
Robert J.K. Wood | 56 | 314 | 10439 |
Howard P. Hodson | 50 | 226 | 7118 |
Martin Rose | 49 | 241 | 10299 |
Andy J. Keane | 46 | 301 | 13753 |
Stephen J. Finney | 45 | 263 | 6821 |
D.M. Vilathgamuwa | 45 | 212 | 7827 |