Rolls-Royce Holdings

About: Rolls-Royce Holdings is a company organization based out in Derby, United Kingdom. It is known for research contribution in the topics: Turbine & Gas compressor. The organization has 4027 authors who have published 6305 publications receiving 80517 citations. The organization is also known as: Rolls-Royce Holdings plc.

Averaging Nonuniform Flow for a Purpose

Abstract: Averaging non-uniform flow is important for the analysis of measurements in turbomachinery and gas turbines; more recently an important need for averaging arises with results of CFD. In this paper we show that there is a method for averaging which is “correct”, in the sense of preserving the essential features of the non-uniform flow, but that the type of averaging which is appropriate depends on the application considered. The crucial feature is the decision to retain or conserve those quantities which are most important in the case considered. Examples are given to demonstrate the appropriate methods to average non-uniform flows in the accounting for turbomachinery blade row performance, production of thrust in a nozzle, and mass flow capacity in a choked turbine. It is also shown that the numerical differences for different types of averaging are, in many cases, remarkably small.Copyright © 2005 by ASME

Gas turbine engine system

Abstract: An aircraft mounted gas turbine engine system comprises a three shaft propulsive gas turbine engine having three electrical generators; each one respectively associated with one shaft of the engine. Two of the electrical generators are additionally configured so as to function as electric motors so as to facilitate power transfer between the engine shafts. One of the electric generators provides the primary source of electrical power for the aircraft, while the remaining electrical generators provide electrical power for the engine and back-up power for the aircraft.

Development of Blade Profiles for Low-Pressure Turbine Applications

Abstract: This paper describes a program of work, largely experimental, which was undertaken with the objective of developing an improved blade profile for the low-pressure turbine in aero-engine applications. Preliminary experiments were conducted using a novel technique. An existing cascade of datum blades was modified to enable the pressure distribution on the suction surface of one of the blades to be altered. Various means, such as shaped inserts, an adjustable flap at the trailing edge, and changing stagger were employed to change the geometry of the passage. These experiments provided boundary layer and lift data for a wide range of suction surface pressure distributions. The data were then used as a guide for the development of new blade profiles. The new blade profiles were then investigated in a low-speed cascade that included a set of moving bars upstream of the cascade of blades to simulate the effect of the incoming wakes from the previous blade row in a multistage turbine environment. Results are presented for two improved profiles that are compared with a datum representative of current practice. The experimental results include loss measurements by wake traverse, surface pressure distributions, and boundary layer measurements. The cascades were operated over a Reynoldsmore » number range from 0.7 {times} 10{sup 5} to 4.0 {times} 10{sup 5}. The first profile is a laminar flow design that was intended to improve the efficiency at the same loading as the datum. The other is a more highly loaded blade profile intended to permit a reduction in blade numbers. The more highly loaded profile is the most promising candidate for inclusion in future designs. It enables blade numbers to be reduced by 20%, without incurring any efficiency penalty. The results also indicate that unsteady effects must be taken into consideration when selecting a blade profile for the low-pressure turbine.« less

A comparative study on dwell fatigue of Ti-6Al-2Sn-4Zr-xMo (x= 2 to 6) alloys on a microstructure-normalized basis

Abstract: The dwell effects of Ti624x (x = 2 to 6) alloys, including dwell fatigue life debit, fracture mode and strain accumulation, were characterized and compared. With increasing Mo content, the dwell fatigue life debit decreases quickly, and dwell fatigue fracture exhibits a transition from subsurface to surface initiation. Accompanying these changes, the accumulated strain decreases, and the pattern of secondary cracks loses morphological features typical of dwell cracks. These variations in the fatigue behavior of Ti624x were attributed on the fundamental level to the dual effects of Mo: It decreases the β transus of titanium and, as a slow diffuser, reduces the rate of phase transformation from β to α. A higher Mo content encourages nucleation of multiple variants of α laths and promotes the transition from aligned colonies to basketweave microstructure during cooling after β forging. As a result both the grain size and microtexture intensity of α grains in the two-phase processed and heat treated microstructure are reduced. Smaller grain size of the alloys with higher Mo content produces smaller slip band spacing and reduces accumulated strain during dwell fatigue, thus reducing propensity for crack initiation. Microtexture was shown to be the direct cause of dwell sensitivity, and their relationship was described with the aid of a two-region redistribution model based on a previous two-element redistribution model proposed by Bache.

Turbine engine control system

Abstract: Fuel flow is scheduled to a plurality of combustion stages by putting a plurality of engine fuel flow governors in parallel with each other and letting the governor which outputs the lowest fuel demand signal be the one which schedules the total fuel flow to the engine. Fuel flows to the plurality of combustion stages are then individually scheduled to achieve the lowest fuel flows consistent with predefined temperature limits for the corresponding stages of combustion.