Journal ArticleDOI
High-speed machining of aluminium alloy using vegetable oil based small quantity lubrication:
Balakrushna Guntreddi,Amitava Ghosh +1 more
- pp 095440542092978
TLDR
In an attempt to investigate the effectiveness of vegetable oil based small quantity lubrication in high-speed machining of aluminium, this paper found that its usefulness is more significant in an...Abstract:
In an attempt to investigate the effectiveness of vegetable oil based small quantity lubrication in high-speed machining of aluminium, this study finds that its usefulness is more significant in an...read more
Citations
More filters
Journal ArticleDOI
Resource saving by optimization and machining environments for sustainable manufacturing: A review and future prospects
TL;DR: The most important aspect of sustainability in manufacturing is the preservation of energy and natural resources as discussed by the authors , which can be achieved by increasing energy efficiency through low, clean, and renewable energy consumption.
Journal ArticleDOI
Dry Machining Performance of AA7075-T6 Alloy Using Uncoated Carbide and MT-CVD TiCN-Al2O3-Coated Carbide Inserts
TL;DR: In this article, the performance of AA7075 T6 alloy with uncoated and MT-CVD TiCN-Al2O3-coated carbide inserts is evaluated with regard to tangential cutting force, tool tip temperature and depth of flank wear.
Journal ArticleDOI
Anti-frictional role of diamond and graphite suspended bio-oil based nano-aerosols at sliding interface of Al-SiCp and WC-6Co
TL;DR: In this article, the authors investigated tribo-phenomena at sliding interface of Al2124-17SiCp disc and WC-6Co pin and explored suitability of nano-oil aerosols as lubricants.
Journal ArticleDOI
Experimental research on machinability characteristics of Al-9Si alloy: Effect of Sr and Mg additives
TL;DR: In this article , the effects of strontium (Sr) and magnesium (Mg) elements in certain rates added to Al-9Si alloy manufactured using permanent mold casting technique on the structural, mechanical, and machinability properties of these alloys were investigated.
References
More filters
Journal ArticleDOI
Cutting conditions and tool optimization in the high-speed milling of aluminium alloys:
TL;DR: The use of high-silicon castings has grown considerably owing to the fact that a high silicon content results in excellent properties, mainly wear and high-temperature resistance as mentioned in this paper, however, the machinability of the material becomes too poor on account of its abrasiveness.
Journal ArticleDOI
Machining comparison of aerospace materials considering minimum quantity cutting fluid: A clean and green approach:
Munish Kumar Gupta,P. K. Sood +1 more
TL;DR: In this paper, the authors proposed an efficient removal of heat from the chip formation zone in the machining of aerospace materials is quite crucial for attaining viability with respect to cost and productivity.
Journal ArticleDOI
Effects of minimum quantity lubricating (MQL) conditions on machining of 7075-T6 aluminum alloy
TL;DR: In this article, the effect of lubrication on the turning of the 7075-T6 aluminum alloy was investigated, and the performance indexes studied are the surface roughness, the chip thickness, and aerosol generation.
Journal ArticleDOI
Investigations of critical cutting speed and ductile-to-brittle transition mechanism for workpiece material in ultra-high speed machining
Bing Wang,Bing Wang,Zhanqiang Liu,Zhanqiang Liu,Guosheng Su,Qinghua Song,Qinghua Song,Xing Ai,Xing Ai +8 more
TL;DR: In this paper, the authors investigated the brittle removal mechanism of ductile materials in ultra-high speed machining (UHSM) and proposed a predictive model of critical cutting speed for UHSM with the theory of stress wave propagation.
Journal ArticleDOI
Investigation of lubricant condition and machining parameters while turning of AISI 4340
TL;DR: In this paper, the effect of various lubrication and machining parameters on tool wear and surface roughness in turning of AISI 4340 has been investigated under three different machining regimes and four strategies of lubrication namely dry, air cool, gaseous, and wet.