Journal ArticleDOI
Measurement and optimization of surface roughness and tool wear via grey relational analysis, TOPSIS and RSA techniques
Reads0
Chats0
TLDR
In this paper, a study to analyze the turning properties of magnesium alloy AZ91D in dry condition with polycrystalline diamond (PCD) cutting inserts is presented, which shows that feed rate and cutting speed are the dominant factors for surface roughness and tool flank wear respectively.About:
This article is published in Measurement.The article was published on 2016-01-01. It has received 96 citations till now. The article focuses on the topics: Surface roughness & Tool wear.read more
Citations
More filters
Journal ArticleDOI
Process monitoring of the AISI D6 steel turning using artificial neural networks
Leonardo Rosa Ribeiro da Silva,Kenji Okada,Felipe Chagas Rodrigues de Souza,Danil Yurievich Pimenov,Álisson Rocha Machado +4 more
Journal ArticleDOI
Tribological behaviour of polycarbonate urethane against Ti-6Al-4V for long-term resilient
Daniels Jacob,Prakash Muniyandi +1 more
TL;DR: In this article , a long-term wear evaluation is carried out to find the wear behavior of polycarbonate urethane against Ti-6Al-4V, which is the most frequently used endplate material in artificial disc replacement.
Journal ArticleDOI
Tool Failure Analysis and Multi-Objective Optimization of a Cutting-Type Energy-Absorbing Structure for Subway Vehicles
TL;DR: In this paper, a new energy-absorbing tube structure was proposed and optimized to improve the crashworthiness and reliability of the cutting energy absorbing structure for subway vehicles, and the impact test results revealed that multiple failure modes occurred in the tool.
Journal ArticleDOI
Influence of milling parameters on Al-Li alloy surface characteristics
TL;DR: In this article , the effect of milling parameters, such as feed rate, cutting speed and depth of cut on surface roughness and hardness have been investigated and presented, and the optimal milling conditions are identified using statistical techniques.
Journal ArticleDOI
Fabrication, microstructure, and machinability of aluminum metal-matrix composites
TL;DR: In this article , the influence of ground granulated blast furnace slag (GGBS) reinforcement composition on the surface roughness and material removal rate of aluminum 6061 MMC was examined, considering the parameters of spindle speed, feed rate, depth of cut, and reinforcement composition percentage.
References
More filters
Journal ArticleDOI
Introduction to Grey system theory
TL;DR: The Grey Systeni and its applications are interdisciplinary, cutting across a variety of specialized fields, and it is evident that Grey System theory stands the test of time since 1982 as mentioned in this paper.
Journal ArticleDOI
Superior light metals by texture engineering: Optimized aluminum and magnesium alloys for automotive applications
Jürgen Hirsch,Talal Al-Samman +1 more
TL;DR: In this article, the basic mechanisms of texture formation of aluminum and magnesium alloys during wrought processing are described and the major aspects and differences in deformation and recrystallization mechanisms are discussed.
Journal ArticleDOI
Research for a new age of magnesium in the automotive industry
H Friedrich,S Schumann +1 more
TL;DR: In this paper, the authors present research strategies for bringing about a new age of magnesium by means of the vehicle modules drive train, interior, body and chassis, differentiated according to the time frame and conceivable likelihood of realisation.
Book
Taguchi techniques for quality engineering : loss function, orthogonal experiments, parameter and tolerance design
TL;DR: The Economics of Reducing Variation The design of Experiment Process as discussed by the authors is a well-known technique for reducing variance in the design of experiment process and is used in many experiments.
Journal ArticleDOI
Manufacturing of Lightweight Components by Metal Forming
TL;DR: In this article, the current and future contributions of forming technology to the manufacture of lightweight components and structures have been discussed, as well as the issues that arise in the production of load adapted designs and using high strength materials.