Journal ArticleDOI
Mechanical and dry sliding wear behaviour of B4C and rice husk ash reinfroced Al 7075 alloy hybrid composite for armors application by using taguchi techniques
Ashiwani Kumar,Mukesh Kumar +1 more
Reads0
Chats0
TLDR
In this article, the authors investigated the mechanical and dry sliding behavior of AA7075-B4C-RHA hybrid alloy composite and obtained the maximum tensile, compressive and flexural strength obtained to be 270, 570, MPa, 570 MPa and 480 MPa respectively.About:
This article is published in Materials Today: Proceedings.The article was published on 2020-01-01. It has received 20 citations till now. The article focuses on the topics: Flexural strength.read more
Citations
More filters
Journal ArticleDOI
A Critical Review on Synthesis of Aluminum Metallic Composites through Stir Casting: Challenges and Opportunities
Journal ArticleDOI
Synthesis and Experimental Investigations of Tribological and Corrosion Performance of AZ61 Magnesium Alloy Hybrid Composites
R. Venkatesh,C. Ramesh Kannan,S. Manivannan,MV Vivekanandan,J. Phani Krishna,Amine Mezni,Saiful Islam,S. Rajkumar +7 more
TL;DR: In this article , the tribological and corrosion performance of AZ61 magnesium alloy with reinforcement of boron carbide (B4C) and zirconium dioxide (ZrO2) was analyzed through Taguchi L27 Orthogonal Array.
Journal ArticleDOI
Influence of agro-based reinforcements on the properties of aluminum matrix composites: a systematic review
TL;DR: In this paper, the influence of agro-based reinforcements on the tribological and mechanical properties of aluminum matrix composites processed by various techniques was studied. And the state-of-the-art revealed that the agrobased reinforcements do not form brittle composites, as in the case of ceramic reinforced composites.
Journal ArticleDOI
Influence of Nanographite on Dry Sliding Wear Behaviour of Novel Encapsulated Squeeze Cast Al-Cu-Mg Metal Matrix Composite Using Artificial Neural Network
L. Natrayan,M. Ravichandran,Dhinakaran Veeman,P. Sureshkumar,T. Jagadeesha,Wubishet Degife Mammo +5 more
TL;DR: In this article, the Taguchi method was used to analyze the dry sliding wear behavior of squeeze cast Al-Cu-Mg reinforced with nanographite metal matrix composites.
Journal ArticleDOI
Wear behaviour of aluminium matrix composites (LM25/Fly Ash) – A Taguchi approach
TL;DR: In this paper, Taguchi technique is opted for optimizing the wear characteristic-Specific Wear Rate (SWR) of composite materials using L27 Orthogonal array and ANOVA was carried out to find the most significant factor and percentage of contribution of each process parameters.
References
More filters
Book
Analysis and Performance of Fiber Composites
TL;DR: In this paper, the authors present an analysis of the properties of fiber-reinforced composites under different types of stress and failure modes, such as failure under longitudinal tensile loads, failure under transverse tensile load, and failure under In-Plane Shear Load.
Journal ArticleDOI
Study on mechanical and wear properties of Al 7075/Al2O3/graphite hybrid composites
A. Baradeswaran,A. Elaya Perumal +1 more
TL;DR: In this article, the influence of graphite on the wear behavior of Al 7075/Al 2 O 3 /5.% graphite hybrid composite was investigated and the results revealed the effectiveness of incorporating graphite in the composite for gaining wear reduction.
Journal ArticleDOI
Influence of B4C on the tribological and mechanical properties of Al 7075–B4C composites
A. Baradeswaran,A. Elaya Perumal +1 more
TL;DR: In this article, the influence of B 4 C on the mechanical and Tribological behavior of Al 7075 composites is identified, and the test results showed increasing hardness of composites compared with the base alloy because of the presence of the increased ceramic phase.
Journal ArticleDOI
Experimental investigation on mechanical behaviour, modelling and optimization of wear parameters of B4C and graphite reinforced aluminium hybrid composites
TL;DR: In this article, the worn surfaces of hybrid composites and base alloys were studied through SEM and EDS systems and some useful conclusions were made by using a pin-on-disc apparatus with various input parameters like applied load (10, 20, and 30 n), sliding speed (0.6, 0.8, and 1.0 n), and sliding distance (1000, 1500, and 2000 m).
Journal ArticleDOI
Evaluation of mechanical properties of aluminium alloy–alumina–boron carbide metal matrix composites
B. Vijaya Ramnath,C. Elanchezhian,M. Jaivignesh,S. Rajesh,C. Parswajinan,A. Siddique Ahmed Ghias +5 more
TL;DR: In this article, the fabrication and mechanical investigation of aluminium alloy, alumina (Al2O3) and boron carbide metal matrix composites is discussed, where the fabrication is done by stir casting which involves mixing the required quantities of additives into stirred molten aluminium.
Related Papers (5)
Characterization and experimental analysis of boron carbide and rice husk ash reinforced AA7075 aluminium alloy hybrid composite
Nishant Verma,S.C. Vettivel +1 more