Journal ArticleDOI
The superconvergent patch recovery and a posteriori error estimates. Part 1: The recovery technique
O. C. Zienkiewicz,J. Z. Zhu +1 more
Reads0
Chats0
TLDR
In this article, a general recovery technique is developed for determining the derivatives (stresses) of the finite element solutions at nodes, which has been tested for a group of widely used linear, quadratic and cubic elements for both one and two dimensional problems.Abstract:
This is the first of two papers concerning superconvergent recovery techniques and a posteriori error estimation. In this paper, a general recovery technique is developed for determining the derivatives (stresses) of the finite element solutions at nodes. The implementation of the recovery technique is simple and cost effective. The technique has been tested for a group of widely used linear, quadratic and cubic elements for both one and two dimensional problems. Numerical experiments demonstrate that the recovered nodal values of the derivatives with linear and cubic elements are superconvergent. One order higher accuracy is achieved by the procedure with linear and cubic elements but two order higher accuracy is achieved for the derivatives with quadratic elements. In particular, an O(h4) convergence of the nodal values of the derivatives for a quadratic triangular element is reported for the first time. The performance of the proposed technique is compared with the widely used smoothing procedure of global L2 projection and other methods. It is found that the derivatives recovered at interelement nodes, by using L2 projection, are also superconvergent for linear elements but not for quadratic elements. Numerical experiments on the convergence of the recovered solutions in the energy norm are also presented. Higher rates of convergence are again observed. The results presented in this part of the paper indicate clearly that a new, powerful and economical process is now available which should supersede the currently used post-processing procedures applied in most codes.read more
Citations
More filters
Journal ArticleDOI
High order optimal anisotropic mesh adaptation using hierarchical elements
TL;DR: The goal of this work is to show how to estimate the error on a finite element solution of degree k using hierarchical basis for Lagrange finite element polynomials and how to use this information to produce optimal anisotropic meshes in a sense that will be precised.
Journal ArticleDOI
Stress recovery procedure for discontinuous deformation analysis
Zhiye Zhao,Jiong Gu +1 more
TL;DR: A stress recovery procedure is proposed for those DDA blocks which are glued together to improve the stress accuracy along the block interface, and can be used for more accurate contact determination.
Proceedings ArticleDOI
On Multi-Dimensional Unstructured Mesh Adaption
William A. Wood,William L. Kleb +1 more
TL;DR: The differences in the treatment of shocks by the adaption schemes, along with the inherently low levels of artificial dissipation in the fluctuation splitting solver, suggest the present method is a strong candidate for applications to compressible gas dynamics.
Journal ArticleDOI
Hierarchical adaptive modeling of structural sandwiches and multilayered composite panels
TL;DR: In this article, the key elements of hierarchical adaptive modeling, multimodel predictor-corrector modeling procedures, potential for solving large complex problems and the needed development to realize this potential are reviewed with special emphasis on applications to multilayered composite panels.
References
More filters
Journal ArticleDOI
A simple error estimator and adaptive procedure for practical engineerng analysis
O. C. Zienkiewicz,J. Z. Zhu +1 more
TL;DR: A new error estimator is presented which is not only reasonably accurate but whose evaluation is computationally so simple that it can be readily implemented in existing finite element codes.
Journal ArticleDOI
Local and global smoothing of discontinuous finite element functions using a least squares method
E. Hinton,John S. Campbell +1 more
TL;DR: In this article, the concepts and potential advantages of local and global least squares smoothing of discontinuous finite element functions are introduced, and the relationship between local smoothing and the reduced integration technique is established.
Journal ArticleDOI
Optimal stress locations in finite element models
TL;DR: In this paper, the existence of optimal points for calculating accurate stresses within finite element models is discussed and a method for locating such points is proposed and applied to several popular finite elements.
Journal ArticleDOI
The post-processing approach in the finite element method—part 1: Calculation of displacements, stresses and other higher derivatives of the displacements
Ivo Babuška,A. Miller +1 more
TL;DR: In this article, a method for post-processing a finite element solution to obtain high accuracy approximations for displacements, stresses, stress intensity factors, etc. is presented.
Journal ArticleDOI
Higher order local accuracy by averaging in the finite element method
James H. Bramble,A. H. Schatz +1 more
TL;DR: In this paper, the authors describe the class of finite element subspaces and explain the main result on the accuracy of K h * u h, where K h is a fixed function, u h represents local averages, and * denotes convolution.
Related Papers (5)
The superconvergent patch recovery and a posteriori error estimates. Part 2: Error estimates and adaptivity
O. C. Zienkiewicz,J. Z. Zhu +1 more
A simple error estimator and adaptive procedure for practical engineerng analysis
O. C. Zienkiewicz,J. Z. Zhu +1 more