Journal ArticleDOI
Experiments with three-dimensional riblets as an idealized model of shark skin
TLDR
In this article, a 3D-riblet surface with sharp-edged fin-shaped elements arranged in an interlocking array was investigated and the turbulent wall shear stress on this surface was measured using direct force balances.Abstract:
The skin of fast sharks exhibits a rather intriguing three-dimensional rib pattern. Therefore, the question arises whether or not such three-dimensional riblet surfaces may produce an equivalent or even higher drag reduction than straight two-dimensional riblets. Previously, the latter have been shown to reduce turbulent wall shear stress by up to 10%. Hence, the drag reduction by three-dimensional riblet surfaces is investigated experimentally. Our idealized 3D-surface consists of sharp-edged fin-shaped elements arranged in an interlocking array. The turbulent wall shear stress on this surface is measured using direct force balances. In a first attempt, wind tunnel experiments with about 365,000 tiny fin elements per test surface have been carried out. Due to the complexity of the surface manufacturing process, a comprehensive parametric study was not possible. These initial wind tunnel data, however, hinted at an appreciable drag reduction. Subsequently, in order to have a better judgement on the potential of these 3D-surfaces, oil channel experiments are carried out. In our new oil channel, the geometrical dimensions of the fins can be magnified 10 times in size as compared to the initial wind tunnel experiments, i.e., from typically 0.5 mm to 5 mm. For these latter oil channel experiments, novel test plates with variable fin configuration have been manufactured, with 1,920–4,000 fins. This enhanced variability permits measurements with a comparatively large parameter range. As a result of our measurements, it can be concluded, that 3D-riblet surfaces do indeed produce an appreciable drag reduction. We found as much as 7.3% decreased turbulent shear stress, as compared to a smooth reference plate. However, in direct comparison with 2D riblets, the performance of 3D-riblets is still inferior by about 1.7%. On the other hand, it appears conceivable, with a careful design of the fin shape (possibly supported by theory), that this inferiority in performance might be reduced. Nevertheless, at present, it seems to be rather unlikely, that 3D-riblets can significantly outperform 2D-riblets. Finally, one interesting finding remains to be mentioned: The optimum drag reduction for short 3D-riblets occurs at a lower rib height than for longer 3D-riblets or for infinitely long 2D-riblets. The same observation had been made previously on shark scales of different species with differing rib lengths, but no explanation could be given.read more
Citations
More filters
Book ChapterDOI
Introduction to Surface Topography
TL;DR: The field of surface topography measurement has been studied extensively as discussed by the authors, including a short historical overview of the field and the current international standards infrastructure and potential future direction for standards are highlighted.
Journal ArticleDOI
Skin-friction drag analysis from the forced convection modeling in simplified underwater swimming
TL;DR: Simple correlations between the surface shear stress and resulting skin-friction drag are derived in terms of the boundary-layer temperature, which may be readily used in underwater swimming situations.
Journal ArticleDOI
A review of drag reduction by riblets and micro-textures in the turbulent boundary layers
Samira Sayad Saravi,Kai Cheng +1 more
TL;DR: In this paper, possible physical mechanisms responsible for turbulent drag reduction have been summarized, and experiments concerning the relationship between the riblets features and the turbulent boundary layer structure has also been reviewed.
Book ChapterDOI
Lotus Effect: Surfaces with Roughness-Induced Superhydrophobicity, Self-Cleaning, and Low Adhesion
TL;DR: In this article, the theory of roughness-induced superhydrophobicity and self-cleaning is presented, followed by the characterization data of natural leaf surfaces and a model of contact angle for oleophilic/phobic surfaces is investigated.
Journal ArticleDOI
Underwater drag reduction by gas
Jiadao Wang,Bao Wang,Darong Chen +2 more
TL;DR: In this paper, the stable existence of gas is a requirement for underwater drag reduction induced by slippage at the water-solid interface, and therefore it is essential to replenish a new gas supply for continued presence of gas at the interface for continued underwater Drag reduction.
References
More filters
Journal ArticleDOI
Turbulent drag reduction research at NASA langley: progress and plans☆
TL;DR: In this article, NASA-Langley research efforts planned at NASA Langley in view of results obtained to date in passive turbulent drag reduction experiments are discussed, including heat transfer-augmentation, noise-reduction, turboprop/fuselage interaction noise reduction, and other advantages.
Related Papers (5)
Shark-skin surfaces for fluid-drag reduction in turbulent flow: a review
Brian Dean,Bharat Bhushan +1 more