Showing papers in "Frontiers of Environmental Science & Engineering in China in 2016"

Chemical poison and regeneration of SCR catalysts for NO x removal from stationary sources

Abstract: Selective catalytic reduction (SCR) of NO x with NH3 is an effective technique to remove NO x from stationary sources, such as coal-fired power plant and industrial boilers. Some of elements in the fly ash deactivate the catalyst due to strong chemisorptions on the active sites. The poisons may act by simply blocking active sites or alter the adsorption behaviors of reactants and products by an electronic interaction. This review is mainly focused on the chemical poisoning on V2O5-based catalysts, environmental-benign catalysts and low temperature catalysts. Several common poisons including alkali/alkaline earth metals, SO2 and heavy metals etc. are referred and their poisoning mechanisms on catalysts are discussed. The regeneration methods of poisoned catalysts and the development of poison-resistance catalysts are also compared and analyzed. Finally, future research directions in developing poisoning resistance catalysts and facile efficient regeneration methods for SCR catalysts are proposed.

Integrated approach to winery waste: waste generation and data consolidation

Abstract: The winemaking process involves the generation of a significant amount of waste and wastewater. These residues should be addressed for recycling or treatment before being returned to environment. As each winery is unique in waste generation and disposal, plans for environmentally friendly waste management are not universal and should be tested for their effectiveness. In this study, a diagnostic was made during three years, in different wineries, throughout Portugal, in order to quantify and characterize the waste and the wastewater produced. The results showed that solid waste and wastewater are mainly produced during the harvest period, corresponding to 74% and 87%, respectively. One ton of processed grape approximately produce 0.13 t marc, 0.06 t lees, 0.03 t of stalks and 1.65 m3 of wastewater. No significant differences (P⩽0.05) were observed for grape marc, lees and wastewater ratios, between years or wineries. With respect to the stalk ratio, there was no effect of year but the winery significantly affected this ratio (P⩽0.05). During the study period the treated wastewater, since diluted, revealed suitable characteristics for irrigation representing an additional source of water. In this regard, the data acquisition and consolidation ensure the transfer of information and experience which constitute an essential step in a support decision tool design.

Long-term observation of air pollution-weather/climate interactions at the SORPES station: a review and outlook

Abstract: This work presents an overall introduction to the Station for Observing Regional Processes of the Earth System–SORPES in Nanjing, East China, and gives an overview about main scientific findings in studies of air pollution-weather/climate interactions obtained since 2011. The main results summarized in this paper include overall characteristics of trace gases and aerosols, chemical transformation mechanisms for secondary pollutants like O3, HONO and secondary inorganic aerosols, and the air pollution–weather/climate interactions and feedbacks in mixed air pollution plumes from sources like fossil fuel combustion, biomass burning and dust storms. The future outlook of the development plan on instrumentation, networking and data-sharing for the SORPES station is also discussed.

A road-map for energy-neutral wastewater treatment plants of the future based on compact technologies (including MBBR)

Abstract: In the paper concepts for domestic wastewater treatment plants of the future are discussed by the use of a) one flow diagram based on established, compact, proven technologies (i.e. nitrification/denitrification for N-removal in the mainstream) and b) one flow diagram based on emerging, compact technologies (i.e. de-ammonification in the main stream).The latter (b) will give an energyneutral wastewater treatment plant, while this cannot be guaranteed for the first one (a). The example flow diagrams show plant concepts that a) minimize energy consumption by using compact biological and physical/chemical processes combined in an optimal way, for instance by using moving bed biofilm reactor (MBBR) processes for biodegradation and high-rate particle separation processes, and de-ammonification processes for N-removal and b)maximize energy (biogas) production through digestion by using wastewater treatment processes that minimize biodegradation of the sludge (prior to digestion) and pretreatment of the sludge prior to digestion by thermal hydrolysis. The treatment plant of the future should produce a water quality (for instance bathing water quality) that is sufficient for reuse of some kind (toilet flushing, urban use, irrigation etc.). The paper outlines compact water reclamation processes based on ozonation in combination with coagulation as pretreatment before ceramic membrane filtration.

Improving simulations of sulfate aerosols during winter haze over Northern China: the impacts of heterogeneous oxidation by NO 2

Abstract: We implemented the online coupled WRF-Chem model to reproduce the 2013 January haze event in North China, and evaluated simulated meteorological and chemical fields using multiple observations. The comparisons suggest that temperature and relative humidity (RH) were simulated well (mean biases are–0.2K and 2.7%, respectively), but wind speeds were overestimated (mean bias is 0.5 m∙s–1). At the Beijing station, sulfur dioxide (SO2) concentrations were overpredicted and sulfate concentrations were largely underpredicted, which may result from uncertainties in SO2 emissions and missing heterogeneous oxidation in current model. We conducted three parallel experiments to examine the impacts of doubling SO2 emissions and incorporating heterogeneous oxidation of dissolved SO2 by nitrogen dioxide (NO2) on sulfate formation during winter haze. The results suggest that doubling SO2 emissions do not significantly affect sulfate concentrations, but adding heterogeneous oxidation of dissolved SO2 by NO2 substantially improve simulations of sulfate and other inorganic aerosols. Although the enhanced SO2 to sulfate conversion in the HetS (heterogeneous oxidation by NO2) case reduces SO2 concentrations, it is still largely overestimated by the model, indicating the overestimations of SO2 concentrations in the North China Plain (NCP) are mostly due to errors in SO2 emission inventory.

Screening the emission sources of volatile organic compounds (VOCs) in China by multi-effects evaluation

Abstract: Volatile organic compounds (VOCs) play important roles in the atmosphere via three main pathways: photochemical ozone formation, secondary organic aerosol production, and direct toxicity to humans. Few studies have integrated these effects to prioritize control measures for VOCs sources. In this study, we developed a multi-effects evaluation methodology based on updated emission inventories and source profiles, by combining the ozone formation potential (OFP), secondary organic aerosol potential (SOAP), and VOC toxicity data. We derived species-specific emission inventories for 152 sources. The OFPs, SOAPs, and toxicity of each source were estimated, the contribution and sharing of source to each of these adverse effects were calculated. Weightings were given to the three adverse effects by expert scoring, and then the integrated effect was determined. Taking 2012 as the base year, solvent use and industrial process were found to be the most important anthropogenic sources, accounting for 24.2% and 23.1% of the integrated effect, respectively, followed by biomass burning, transportation, and fossil fuel combustion, each had a similar contribution ranging from 16.7% to 18.6%. The top five industrial sources, including plastic products, rubber products, chemical fiber products, the chemical industry, and oil refining, accounted for nearly 70.0% of industrial emissions. Beijing, Chongqing, Shanghai, Jiangsu, and Guangdong were the five provinces contributing the largest integrated effects. For the VOC species from emissions showed the largest contributions were styrene, toluene, ethylene, benzene, and m/p-xylene.

Recent advances in pharmaceuticals and personal care products in the surface water and sediments in China

Abstract: Pharmaceuticals and personal care products (PPCPs) have been regarded as an emerging problem in the surface water environment in the past few decades. In China, although related studies were initiated several years ago, an increasing number of studies on this topic have been conducted in recent years. These studies have expanded knowledge of their occurrence, behavior and associated risk in the surface water environment in China. This review compiles the most recent literature related to the studies of PPCPs in the surface water environment in China. It includes PPCP occurrence in surface water and sediments, their geographical distribution, and outcomes of the associated risk assessment. It shows that antibiotics have received much more attention in both surface water and sediments than other PPCPs. Compared to other countries; most antibiotics in the collected sediments in China showed higher contamination levels. Many more study areas have been covered in recent years; however, attention has been given to only specific areas. Environmental risk assessment based on risk quotients indicated that sulfamethoxazole presents the most significant environmental risk to relevant aquatic organisms; followed by ofloxacin, ciprofloxacin, enrofloxacin, 17α-ethynylestradiol, ibuprofen and diclofenac. Despite limited research on the environmental risk assessment of PPCPs in sediments, higher risks posed by PPCPs in the sediments rather than surface water were identified highlighting the need for further risk assessment of PPCPs in sediment samples.

On secondary new particle formation in China

Abstract: Formation of new atmospheric aerosol particles is a global phenomenon that has been observed to take place in even heavily-polluted environments. However, in all environments there appears to be a threshold value of the condensation sink (due to pre-existing aerosol particles) after which the formation rate of 3 nm particles is no longer detected. In China, new particle production has been observed at very high pollution levels (condensation sink about 0.1 s–1) in several megacities, including Beijing, Shanghai and Nanjing as well as in Pearl River Delta (PRD). Here we summarize the recent findings obtained from these studies and discuss the various implications these findings will have on future research and policy.

Effect of ultraviolet irradiation and chlorination on ampicillin-resistant Escherichia coli and its ampicillin resistance gene

Abstract: Antibiotic resistance is a serious public health risk that may spread via potable and reclaimed water. Effective disinfection is important for inactivation of antibiotic-resistant bacteria and disruption of antibiotic resistance genes. Ampicillin is a widely prescribed antibiotic but its effectiveness is increasingly undermined by resistance. In this study, changes in ampicillin resistance for Escherichia coli (E. coli) CGMCC 1.1595 were analyzed after exposure to different doses of ultraviolet (UV) or chlorine, and damage incurred by the plasmid encoding ampicillin resistance gene bla TEM-1 was assessed. We reported a greater stability in ampicillinresistant E. coli CGMCC 1.1595 after UV irradiation or chlorination when compared with previously published data for other E. coli strains. UV irradiation and chlorination led to a shift in the mortality frequency distributions of ampicillin-resistant E. coli when subsequently exposed to ampicillin. The ampicillin hemiinhibitory concentration (IC50) without disinfection was 3800 mg·L–1, and an increment was observed after UV irradiation or chlorination. The IC50 of ampicillin-resistant E. coli was 1.5-fold higher at a UV dose of 40 mJ·cm–2, and was 1.4-fold higher when exposed to 2.0 mg·L–1 chlorine. These results indicate that UV irradiation and chlorination can potentially increase the risk of selection for E. coli strains with high ampicillin resistance. There was no evident damage to bla TEM-1 after 1–10 mg Cl2·L–1 chlorination, while a UV dose of 80 mJ·cm–2 yielded a damage ratio for bla TEM-1 of approximately 1.2-log. Therefore, high UV doses are required for effective disruption of antibiotic resistance genes in bacteria.

Effective degradation of tetracycline by mesoporous Bi 2 WO 6 under visible light irradiation

Abstract: Bi2WO6 was synthesized with a hydrothermal method at different pHs and used for the degradation of tetracycline (TC) in water. The mesoporous Bi2WO6 prepared at pH 1 (BWO-1) displayed the highest adsorption and degradation capacity to TC due to its large surface area and more efficient capacity to separate photogenerated electrons and holes. 97% of TC at 20 mg·L−1 was removed by BWO-1 at 0.5 g·L−1 after 120 min irradiation under simulated solar light. Only 31% of the total organic carbon (TOC) was removed after 360 min irradiation although the TC removal reached 100%, suggesting that TC was mainly transformed to intermediate products rather than completely mineralized. The intermediates were identified by high-performance liquid chromatography-time of flight-mass spectrometry (HPLC-TOF-MS) and possible photodegradation pathways were proposed.

Fate and removal of typical pharmaceutical and personal care products in a wastewater treatment plant from Beijing: a mass balance study

Abstract: The fate and removal of pharmaceuticals and personal care products (PPCPs) in wastewater treatment plants (WWTPs) has received great attention during the last decade. Numerous data concerning concentrations in the water phase can be found in the literature, however corresponding data from sludge as well as associated mass balance calculations are very limited. In the present study, the adsorbed and dissolved concentrations of 9 PPCPs were investigated in each unit of a WWTP in Beijing, China. Based on the calculation of mass balance, the relative mass distribution and removal efficiency of each target compound was obtained at each process. The amount of PPCPs entering into the WWTP ranged from 12 g·d–1 to 3848 g·d–1. Five target compounds (caffeine, chloramphenicol, bezafibrate, clofibric acid, and N,N-diethyl-meta-toluamide) were effectively removed, with rates of 57%–100%. Negative removal efficiencies were obtained for sulpiride, metoprolol, nalidixic acid, and carbamazepine, ranging from -19% to -79%. PPCPs mainly existed in dissolved form (≥92%) in both the raw influent and the final effluent. The sludge cake carried a much lower amount of PPCPs (17 g·d–1) compared with the discharged effluent (402 g·d–1). In A2/O treatment tanks, the anaerobic and anoxic tanks showed good performance for PPCPs removal, and the amount of adsorbed PPCPs was increased. The results reveal that both the dissolved and the adsorbed phases should be considered when assessing the removal capacity of each A2/O tank.

A spectrometer for measuring particle size distributions in the range of 3 nm to 10 μm

Abstract: A spectrometer combining electrical mobility sizing and aerodynamic sizing was developed to measure aerosol size distributions in the range of 3 nm to 10 μm. It includes three instruments which cover different size ranges (a nano scanning mobility particle sizer (NSMPS, 3–60 nm), a regular scanning mobility particle sizer (RSMPS, 40–700 nm), and an aerodynamic particle sizer (APS, 550 nm–10 μm)). High voltage and sheath flow of the NSMPS and RSMPS were supplied using two home-built control boxes. A LabVIEW program was developed for spectrometer automatic operation. A linear inversion method was applied to correct particle multiple charging effects and to integrate data from the three instruments into a wide-range size distribution. Experiments were conducted to compare distributions in the overlap size ranges measured by three instruments. Good agreement between the NSMPS and RSMPS was achieved after correcting for the difference in counting efficiencies of the two particle counters. Aerodynamic size distributions reported by the APS were converted to mobility size distributions by applying an effective density method. Distributions measured by the RSMPS and APS were consistent in the overlap size range of 550–700 nm. A full spectrum in the size range of 3 nm to 10 μm was demonstrated by measuring aerosol generated using a mixture of different sized polystyrene latex spheres.

Air quality improvement in Los Angeles—perspectives for developing cities

Abstract: Air quality improvement in Los Angeles, California is reviewed with an emphasis on aspects that may inform air quality policy formulation in developing cities. In the mid-twentieth century the air quality in Los Angeles was degraded to an extent comparable to the worst found in developing cities today; ozone exceeded 600 ppb and annual average particulate matter <10 μm reached ~150 mg∙m–3. Today's air quality is much better due to very effective emission controls; e.g., modern automobiles emit about 1% of the hydrocarbons and carbon monoxide emitted by vehicles of 50 years ago. An overview is given of the emission control efforts in Los Angeles and their impact on ambient concentrations of primary and secondary pollutants; the costs and health benefits of these controls are briefly summarized. Today's developing cities have new challenges that are discussed: the effects of regional pollution transport are much greater in countries with very high population densities; often very large current populations must be supplied with goods and services even while economic development and air quality concerns are addressed; and many of currently developing cities are located in or close to the tropics where photochemical processing of pollution is expected to be more rapid than at higher latitudes. The air quality issues of Beijing are briefly compared and contrasted with those of Los Angeles, and the opportunities for co-benefits for climate and air quality improvement are pointed out.

Evaluation of the k-nearest neighbor method for forecasting the influent characteristics of wastewater treatment plant

Abstract: The k-nearest neighbor (k-NN) method was evaluated to predict the influent flow rate and four water qualities, namely chemical oxygen demand (COD), suspended solid (SS), total nitrogen (T-N) and total phosphorus (T-P) at a wastewater treatment plant (WWTP). The search range and approach for determining the number of nearest neighbors (NNs) under dry and wet weather conditions were initially optimized based on the root mean square error (RMSE). The optimum search range for considering data size was one year. The square root-based (SR) approach was superior to the distance factor-based (DF) approach in determining the appropriate number of NNs. However, the results for both approaches varied slightly depending on the water quality and the weather conditions. The influent flow rate was accurately predicted within one standard deviation of measured values. Influent water qualities were well predicted with the mean absolute percentage error (MAPE) under both wet and dry weather conditions. For the seven-day prediction, the difference in predictive accuracy was less than 5% in dry weather conditions and slightly worse in wet weather conditions. Overall, the k-NN method was verified to be useful for predicting WWTP influent characteristics.

Sorption and desorption of pymetrozine on six Chinese soils

Abstract: Pymetrozine is a selective insecticide with a unique chemical structure and mode to control hemipteran and homopteran. While pymetrozine has brought great benefits to crop production by killing insects, its residues in soil may have a detrimental effect on environment. Therefore, it is of great importance to investigate its behaviors in soil. In this study, the sorption and desorption of pymetrozine on six Chinese soils were investigated using a batch equilibrium approach to understand its mobile behavior in the soils. Both sorption and desorption isotherms of pymetrozine were in good agreement with the Freundlich model. The sorption coefficient KF varied between 3.37 and 58.32 mL·g−1 and the sorption isotherms were nonlinear, with 1/n ranging from 0.57 to 0.91. A regression equation was proposed to predict the sorption of pymetrozine on six different soil samples: log KF = 4.3708 − 4.5709 × log (pH in 0.01mol·L−1 CaCl2) + 0.4700 × log OC% + 0.0057 × sand (%) + 0.0022 × CEC(clay), with R2 = 0.9982. The organic carbon content of soil positively affected the sorption of pymetrozine, but soil pH had a negative effect on the sorption. Additionally, effects of CaCl2 concentration, soil to solution ratio and pesticide form were investigated. The sorption was promoted with an increase in soil to solution ratio and a decrease in CaCl2 concentration. The possible variation of the five formulated products of pymetrozine was also investigated.

Vacuum promotes metabolic shifts and increases biogenic hydrogen production in dark fermentation systems

Abstract: The successful operation of any type of hydrogen-producing bioreactor depends on the performance of the microorganisms present in the system. Both substrate and partial gas pressures are crucial factors affecting dark fermentation metabolic pathways. The main objective of this study was to evaluate the impact of both factors on hydrogen production using anaerobic granular sludge as inoculum and, secondly, to study the metabolic shifts of an anaerobic community subjected to low partial gas pressures. With this goal in mind, seven different wastewater (four synthetic media, two industrial wastewater, and one domestic effluent) and the effect of applying vacuum on the systems were analyzed. The application of vacuum promoted an increase in the diversity of hydrogenproducing bacteria, such as Clostridium, and promoted the dominance of acetoclastic- over hydrogenotrophic methanogens. The application of different media promoted a wide variety of metabolic pathways. Nevertheless, reduction of the hydrogen partial pressure by application of vacuum lead to further oxidation of reaction intermediates irrespective of the medium used, which resulted in higher hydrogen and methane production, and improved the COD removal. Interestingly, vacuum greatly promoted biogenic hydrogen production from a real wastewater, which opens possibilities for future application of dark fermentation systems to enhance biohydrogen yields.

Enhanced degradation of trichloroethene by calcium peroxide activated with Fe(III) in the presence of citric acid

Abstract: Trichloroethene (TCE) degradation by Fe(III)-activated calcium peroxide (CP) in the presence of citric acid (CA) in aqueous solution was investigated. The results demonstrated that the presence of CA enhanced TCE degradation significantly by increasing the concentration of soluble Fe(III) and promoting H2O2 generation. The generation of HO• and O2-• in both the CP/Fe(III) and CP/Fe(III)/CA systems was confirmed with chemical probes. The results of radical scavenging tests showed that TCE degradation was due predominantly o direct oxidation by HO•, while O2-• strengthened the generation of HO• by promoting Fe(III) transformation in the CP/Fe(III)/CA system. Acidic pH conditions were favorable for TCE degradation, and the TCE degradation rate decreased with increasing pH. The presence of Cl-, HCO3-, and humic acid (HA) inhibited TCE degradation to different extents for the CP/Fe(III)/CA system. Analysis of Cl- production suggested that TCE degradation in the CP/Fe(III)/CA system occurred through a dechlorination process. In summary, this study provided detailed information for the application of CA-enhanced Fe(III)-activated calcium peroxide for treating TCE contaminated groundwater.

Long-term trends of fine particulate matter and chemical composition in the Pearl River Delta Economic Zone (PRDEZ), China

Abstract: Understanding the trends in PM2.5 levels is essential for formulating clean air plans. This paper analyzes PM2.5 data from various published sources for the years 2000 to 2010 in the Pearl River Delta Economic Zone (PRDEZ). The long-term variation in PM2.5 mass concentration is analyzed. Results show that PM2.5, organic carbon (OC), elemental carbon (EC), and SO 4 2− show a similar trend, increasing before 2005 and then decreasing slightly. The annual average PM2.5 concentration ranges from 49.1 μg·m−3 in 2000 to 64.3 μg·m−3 in 2010, with a peak of 84.1 μg·m−3 in 2004. None of these 11 years meets the new National Ambient Air Quality standard (NAAQS) for PM2.5 (35 μg·m−3). Overall average concentrations of OC, EC, and SO 4 2− are 13.0, 6.5, and 11.8 μg·m−3, respectively. NO 3 − and NHþ4 respectively have concentrations of 1.5 μg·m−3 and 2.9 μg·m−3 in 2000 and 6.4 μg·m−3 and 5.3 μg·m−3 in 2010, with a statistically significant average annual trend of + 0.2 μg·m−3·yr−1 and + 0.1 μg·m−3·yr−1. In certain geographic regions, OC and EC contribute most of the PM2.5, while in other regions secondary water-soluble ions are more important. In general, OC and SO 4 2− are the dominant components of PM2.5, contributing 20.6% and 18.6%, respectively. These results provide, for the first time, a better understanding of the long-term PM2.5 characteristics and trends, on a species-by-species basis, in the PRDEZ. The results indicate that PM2.5 abatement needs to prioritize secondary species.

Removing carbonyl sulfide with metal-modified activated carbon

Abstract: A Cu-Co-K/activated carbon (AC) adsorbent has been developed for the removal of carbonyl sulfide (COS). The effects of COS concentration, reaction temperature and relative humidity were closely examined. A breakthrough of 33.23 mg COS·g−1 adsorbent at 60°C, under 30% relative humidity and in presence of 1.0% oxygen was exhibited in the Cu-Co-K/AC adsorbent prepared. Competitive adsorption studies for COS in the presence of CS2, and H2S were also conducted. TPD analysis was used to identify sulfur-containing products on the carbon surface, and the results indicated that H2S, COS and SO2 were all evident in the effluent gas generated from the exhausted Cu-Co-K/AC. Structure of the activated carbon samples has been characterized using nitrogen adsorption, and their surface chemical structures were also determined with X-ray photoelectron spectroscopy (XPS). It turns out that the modification with Cu(OH)2CO3-CoPcS-KOH can significantly improve the COS removal capacity, forming SO42− species simultaneously. Regeneration of the spent activated carbon sorbents by thermal desorption has also been explored.

Characteristics of carbonyls and volatile organic compounds (VOCs) in residences in Beijing, China

Abstract: Volatile organic compounds (VOCs) and carbonyl compounds were measured both indoors and outdoors in 50 residences of Beijing in heating (December, 2011) and non-heating seasons (April/May, 2012). SUMMA canisters for VOCs and diffusive samplers for carbonyl compounds were deployed for 24 h at each site, and 94 compounds were quantified. Formaldehyde, acetone and acetaldehyde were the most abundant carbonyl compounds both indoors and outdoors with indoor median concentrations being 32.1, 21.7 and 15.3 μg·m−3, respectively. Ethane (17.6 μg·m−3), toluene (14.4 μg·m−3), propane (11.2 μg·m−3), ethene (8.40 μg·m−3), n-butane (6.87 μg·m−3), and benzene (5.95 μg·m−3) showed the high median concentrations in indoor air. Dichloromethane, pdichlorobenzene (p-DCB) and toluene exhibited extremely high levels in some residences, which were related with a number of indoor emission sources. Moreover, isoprene, pdichlorobenzene and carbonyls showed median indoor/ outdoor (I/O) ratios larger than 3, indicating their indoor sources were prevailing. Chlorinated compounds like CFCs were mainly from outdoor sources for their I/O ratios being less than 1. In addition, indoor concentrations between two sampling seasons varied with different compounds. Carbonyl compounds and some chlorinated compounds had higher concentrations in the non-heating season, while alkanes, alkenes, aromatic compounds showed an increase in the heating season. Indoor concentration of VOCs and carbonyls were influenced by locations, interior decorations and indoor activities, however the specific sources for indoor VOCs and carbonyls could not be easily identified. The findings obtained in this study would significantly enhance our understandings on the prevalent and abundant species of VOCs as well as their concentrations and sources in Beijing residences.

Enhanced disinfection of Escherichia coli and bacteriophage MS2 in water using a copper and silver loaded titanium dioxide nanowire membrane

Abstract: Titanium dioxide (TiO2) is a widely used photocatalyst that has been demonstrated for microorganism disinfection in drinking water. In this study, a new material with a novel structure, silver and copper loaded TiO2 nanowire membrane (Cu-Ag-TiO2) was prepared and evaluated for its efficiency to inactivate E. coli and bacteriophage MS2. Enhanced photo-activated bactericidal and virucidal activities were obtained by the Cu-Ag-TiO2 membrane than by the TiO2, Ag-TiO2 and Cu-TiO2 membranes under both dark and UV light illumination. The better performance was attributed to the synergies of enhanced membrane photoactivity by loading silver and copper on the membrane and the synergistic effect between the free silver and copper ions in water. At the end of a 30 min test of deadend filtration under 254 nm UV irradiation, the Cu-Ag-TiO2 membrane was able to obtain an E. coli removal of 7.68 log and bacteriophage MS2 removal of 4.02 log, which have met the US EPA standard. The free metal ions coming off the membrane have concentrations of less than 10 ppb in the water effluent, far below the US EPA maximum contaminant level for silver and copper ions in drinking water. Therefore, the photo-activated disinfection by the Cu-Ag-TiO2 membrane is a viable technique for meeting drinking water treatment standards of microbiological water purifiers.

Life cycle assessment of low impact development technologies combined with conventional centralized water systems for the City of Atlanta, Georgia

Abstract: Low-impact development (LID) technologies, such as bioretention areas, rooftop rainwater harvesting, and xeriscaping can control stormwater runoff, supply non-potable water, and landscape open space. This study examines a hybrid system (HS) that combines LID technologies with a centralized water system to lessen the burden on a conventional system (CS). CS is defined as the stormwater collection and water supply infrastructure, and the conventional landscaping choices in the City of Atlanta. The study scope is limited to five single-family residential zones (SFZs), classified R-1 through R-5, and four multi-family residential zones (MFZs), classified RG-2 through RG-5. Population density increases from 0.4 (R-1) to 62.2 (RG-5) persons per 1,000 m2. We performed a life cycle assessment (LCA) comparison of CS and HS using TRACI 2.1 to simulate impacts on the ecosystem, human health, and natural resources.We quantified the impact of freshwater consumption using the freshwater ecosystem impact (FEI) indicator. Test results indicate that HS has a higher LCA single score than CS in zones with a low population density; however, the difference becomes negligible as population density increases. Incorporating LID in SFZs and MFZs can reduce potable water use by an average of 50% and 25%, respectively; however, water savings are negligible in zones with high population density (i.e., RG-5) due to the diminished surface area per capita available for LID technologies. The results demonstrate that LID technologies effectively reduce outdoor water demand and therefore would be a good choice to decrease the water consumption impact in the City of Atlanta.

Combustion effects and emission characteristics of SO2, CO, NOx and heavy metals during co-combustion of coal and dewatered sludge

Abstract: The influences of dewatered sludge blending ratio in coal on flammability index (C) and combustion characteristic index (S) and release of sulfur dioxide (SO2), nitrogen oxide (NO x ), carbon monoxide (CO) and heavy metals (Hg, As, Cd, Pb and Cr) were studied. The impact on combustion characteristics could be ignored if less than 20% of dewatered sludge was added in coal. Besides, emission pattern experiments of NO x , SO2, CO and heavy metals were carried out in a high-temperature tubular furnace. Results showed that the conversion rate of NO x and total emission of SO2 reduced with the increase of sludge adding ratio, and a better effect of fixing sulfur could be obtained when the blending ratio reached 30%. Concentrations and distributions of five types of heavy metals in different residues (bottom ash and fly ash) as well as in flue gas were analyzed. It was shown that the characteristics of coal and sludge, as well as the volatilization of heavy metals had a great influence on the distribution of heavy metals.

Photochemical indicators of ozone sensitivity: application in the Pearl River Delta, China

Abstract: Surface O3 production has a highly nonlinear relationship with its precursors. The spatial and temporal heterogeneity of O3-NO x -VOC-sensitivity regimes complicates the control-decision making. In this paper, the indicator method was used to establish the relationship between O3 sensitivity and assessment indicators. Six popular ratios indicating ozone-precursor sensitivity, HCHO/NO y , H2O2/ HNO3, O3/NO y , O3/NO z , O3/HNO3, and H2O2/NO z , were evaluated based on the distribution of NOx- and VOC-sensitive regimes. WRF-Chem was used to study a serious ozone episode in fall over the Pearl River Delta (PRD). It was found that the south-west of the PRD is characterized by a VOCsensitive regime, while its north-east is NO x -sensitive, with a sharp transition area between the two regimes. All indicators produced good representations of the elevated ozone hours in the episode on 6 November 2009, with H2O2/HNO3 being the best indicator. The threshold sensitivity levels for HCHO/NOy, H2O2/HNO3, O3/NO y , O3/NO z , O3/HNO3, and H2O2/NO z were estimated to be 0.41, 0.55, 10.2, 14.0, 19.1, and 0.38, respectively. Threshold intervals for the indicators H2O2/HNO3, O3/NO y , O3/NO z , O3/HNO3, and H2O2/NO z were able to identify more than 95% of VOC- and NO x -sensitive grids. The ozone episode on 16 November 16 2008 was used to independently verify the results, and it was found that only H2O2/HNO3 and H2O2/NO z were able to differentiate the ozone sensitivity regime well. Hence, these two ratios are suggested as the most appropriate indicators for identifying fall ozone sensitivity in the PRD. Since the species used for indicators have seasonal variation, the utility of those indicators for other seasons should be investigated in the future work.

Fe-Mn-sepiolite as an effective heterogeneous Fenton-like catalyst for the decolorization of reactive brilliant blue

Abstract: A study of the decolorization of reactive brilliant blue in an aqueous solution using Fe-Mn-sepiolite as a heterogeneous Fenton-like catalyst has been performed. The Fourier transform infrared (FTIR) spectra of the catalyst showed bending vibrations of the Fe-O. The Xray diffraction (XRD) patterns of the catalyst showed characteristic diffraction peaks of α-Fe2O3, γ-Fe2O3 and MnO. A four factor central composite design (CCD) coupled with response surface methodology (RSM) was applied to evaluate and optimize the important variables (catalyst addition, hydrogen peroxide dosage, initial pH value and initial dye concentration). When the reaction conditions were catalyst dosage = 0.4 g, [H2O2]= 0.3 mL, pH = 2.5, [reactive brilliant blue]o = 50mg·L−1, and volume of solution = 500 mL at room temperature, the decolorization efficiency of reactive brilliant blue was 91.98% within 60 min. Moreover, the Fe-Mn-sepiolite catalyst had good stability for the degradation of reactive brilliant blue even after six cycles. Leaching of iron ions (<0.4 mg·L−1) was observed. The decoloring process was reactive brilliant blue specific via a redox reaction. The benzene ring and naphthalene ring were first oxidized to open ring; these were then oxidized to the alcohol and carboxylic acid. The reactive brilliant blue was decomposed mainly by the attack of ·OH radicals including surface-bound ·OH radicals generated on the catalyst surface.

Leaching toxicity characteristics of municipal solid waste incineration bottom ash

Abstract: The continuously increasing production of municipal solid waste incineration bottom ash (MSWIBA) has promoted its utilization as construction material and raised environmental concern. The physico-chemical properties and leaching behavior of MSWIBA were studied, and ecotoxicological testing using a luminescent bacterium bioassay was performed to assess the ecological pollution risks associated with its leached constituents. The MSWIBA was leached by two types of leachants, H2SO4/HNO3 and HAc solution, at different liquid to solid ratios and contact times. The concentrations of heavy metals and anions in the leachates were analyzed. Multivariate statistical analyses, including principle component analysis, Pearson’s correlation analysis and hierarchical cluster analysis, were used to evaluate the contributions of the constituents to the toxicity (EC 50) of the MSWIBA leachate. The statistical analyses of the ecotoxicological results showed that the Ba, Cr, Cu, Pb, F−and total organic carbon (TOC) concentrations were closely correlated with the EC 50 value, and these substances were the main contributors to the ecotoxicity of the MSWIBA leachate. In addition, the cluster of these variables indicated similar leaching behaviors. Overall, the research demonstrated that the ecotoxicological risks resulting from MSWIBA leaching could be assessed before its utilization, which provides crucial information for the adaptation of MSWIBA as alternative materials.

An electrochemical process that uses an Fe 0 /TiO 2 cathode to degrade typical dyes and antibiotics and a bio-anode that produces electricity

Abstract: In this study, a new water treatment system that couples (photo-) electrochemical catalysis (PEC or EC) in a microbial fuel cell (MFC) was configured using a stainless-steel (SS) cathode coated with Fe0/TiO2. We examined the destruction of methylene blue (MB) and tetracycline. Fe0/TiO2 was prepared using a chemical reduction-deposition method and coated onto an SS wire mesh (500 mesh) using a sol technique. The anode generates electricity using microbes (bio-anode). Connected via wire and ohmic resistance, the system requires a short reaction time and operates at a low cost by effectively removing 94% MB (initial concentration 20 mg∙L–1) and 83% TOC/TOC0 under visible light illumination (50 W; 1.99 mW∙cm–2 for 120 min, MFC-PEC). The removal was similar even without light irradiation (MFC-EC). The E Eo of the MFC-PEC system was approximately 0.675 kWh∙m–3∙order–1, whereas that of the MFC-EC system was zero. The system was able to remove 70% COD in tetracycline solution (initial tetracycline concentration 100 mg∙L–1) after 120 min of visible light illumination; without light, the removal was 15% lower. The destruction of MB and tetracycline in both traditional photocatalysis and photoelectrocatalysis systems was notably low. The electron spinresonance spectroscopy (ESR) study demonstrated that ∙OH was formed under visible light, and ∙O 2 – was formed without light. The bio-electricity-activated O2 and ROS (reactive oxidizing species) generation by Fe0/TiO2 effectively degraded the pollutants. This cathodic degradation improved the electricity generation by accepting and consuming more electrons from the bio-anode.

Effects of sepiolite on stabilization remediation of heavy metal-contaminated soil and its ecological evaluation

Abstract: Stabilization in the remediation of heavy metal contaminated soils has been gaining prominence because of its cost-effectiveness and rapid implementation. In this study, microbial properties such as microbial community and enzyme activities, chemical properties such as soil pH and metal fraction, and heavy metal accumulation in spinach (Spinacia oleracea) were considered in assessing stabilization remediation effectiveness using sepiolite. Results showed that soil pH values increased with rising sepiolite concentration. Sequential extraction results indicated that the addition of sepiolite converted significant amounts of exchangeable fraction of Cd and Pb into residual form. Treatments of sepiolite were observed to reduce Cd and Pb translocation from the soil to the roots and shoots of spinach. Concentrations of Cd and Pb exhibited 12.6%–51.0% and 11.5%–46.0% reduction for the roots, respectively, and 0.9%–46.2% and 43.0%–65.8% reduction for the shoots, respectively, compared with the control group. Increase in fungi and actinomycete counts, as well as in catalase activities, indicated that soil metabolic recovery occurred after sepiolite treatments.

Characterization of chlorine and heavy metals for the potential recycling of bottom ash from municipal solid waste incinerators as cement additives

Abstract: Bottom ash is an inevitable by-product from municipal solid waste (MSW) incineration plants. Recycling it as additives for cement production is a promising disposal method. However, the heavy metals and chlorine are the main limiting factors because of the potential environmental risks and corrosion of cement kilns. Therefore, investigating heavy metal and chlorine characteristics of bottom ash is the significant prerequisite of its reuse in cement industries. In this study, a correlative analysis was conducted to evaluate the effect of the MSW components and collection mode on the heavy metal and chlorine characteristics in bottom ash. The chemical speciation of insoluble chlorine was also investigated by synchrotron X-ray diffraction analysis. The results showed that industrial waste was the main source of heavy metals, especially Cr and Pb, in bottom ash. The higher contents of plastics and kitchen waste lead to the higher chlorine level (0.6 wt.%–0.7 wt.%) of the bottom ash. The insoluble chlorine in the MSW incineration bottom ash existed primarily as AlOCl, which was produced under the high temperature (1250°C) in incinerators. Open image in new window

Is there an inverted U-shaped curve? Empirical analysis of the Environmental Kuznets Curve in agrochemicals

Abstract: As the largest contributor to water impairment, agriculture-related pollution has attracted the attention of scientists as well as policy makers, and quantitative information is being sought to focus and advance the policy debate. This study applies the panel unit root, heterogeneous panel cointegration, and panel-based dynamic ordinary least squares to investigate the Environmental Kuznets Curve on environmental issues resulting from use of agricultural synthetic fertilizer, pesticide, and film for 31 provincial economies in mainland China from 1989 to 2009. The empirical results indicate a positive long-run co-integrated relationship between the environmental index and real GDP per capita. This relationship takes on the inverted U-shaped Environmental Kuznets Curve, and the value of the turning point is approximately 10,000–13,000, 85,000–89,000 and over 160,000 CNY, for synthetic fertilizer nitrogen indicator, fertilizer phosphorus indicator and pesticide indicator, respectively. At present, China is subject to tremendous environmental pressure and should assign more importance to special agriculture-related environmental issues.