Korean Journal of Optics and Photonics 

About: Korean Journal of Optics and Photonics is an academic journal. The journal publishes majorly in the area(s): Laser & Lens (optics). It has an ISSN identifier of 1225-6285. It is also open access. Over the lifetime, 846 publications have been published receiving 928 citations.

Color Filter Based on a Sub-wavelength Patterned Metal Grating

Abstract: A color filter was demonstrated incorporating a patterned metal grating in a quartz substrate. The filter is created in a metal layer perforated with a symmetric two-dimensional array of circular holes, with the pitch smaller than the wavelength of the visible light. A finite-difference time-domain simulation was performed to analyze the device by investigating the effect of structural parameters like the grating height, the period, the hole size, and the refractive index of the hole-filling material on its performance. The device performance was especially optimized by controlling the refractive index of the material comprising the holes of the grating. And two different devices were fabricated by means of the e-beam direct writing with the following design parameters: the grating height of 50 nm, the two pitches of 340 nm for the red color and 260 nm for the green color. For the prepared device with the period of 340 nm, the center wavelength was 680 nm and the peak transmission 57%. And for the other device with the pitch of 260 nm, the center wavelength was 550 nm and the peak transmission was 50%. The filling of the hole with a material whose refractive index is matched to that of the substrate has led to an increase of in the transmission efficiency.

Pressure Dependence of Acoustic Properties of Liquid Ethanol by using High-pressure Brillouin Spectroscopy

Abstract: Brillouin spectroscopy has been widely used for the investigation of acoustic properties of condensed matters in the hypersonic region. A high-pressure Brillouin spectrometer was set up by combining a diamond anvil cell and a tandem multi-pass Fabry-Perot interferometer. It was successfully applied to liquid ethanol, and the pressure dependence of the sound velocity, the refractive index and other acoustic properties were derived based on the measurements. The detailed optical setup and experimental procedure are described.

Optical Simulation Study on the Performances of Collimating Films for LCD Backlight Applications

Abstract: Optical simulation methods such as a ray tracing technique have been widely used to predict the optical performances of collimating films for LCD backlight applications. It is necessary to optimize simulation conditions which have substantial effect on the simulation result in order to predict accurate performances of collimating films. We have set up a very simple backlight model consisting of a reflection film, a virtual flat light-source, and a prism film, which is a representative collimating film for backlight, in order to analyze the simulation conditions which are strongly correlated with the on-axis luminance gain and the viewing-angle characteristics of prism films. It was found that the dependence of the relative change in the on-axis luminance on the structure and material properties of collimating films can be derived from the above-mentioned simple BLU model and from simulation using it. However, the exact reflection property of the reflection film and the distribution of the incident light onto the optical film were found to be very important for revealing exact viewing-angle characteristics of collimating films.

Optimization of Optical Structure of Lightguide Panel for Uniformity Improvement of Edge-lit Backlight

Abstract: Optical simulation methods were applied to the edge-lit LED backlight for LCD TV applications in order to optimize the optical structure of the light guide plate(LGP), and thus to improve the uniformity properties by removing the bright spots caused by LED’s. The edge-lit LED backlight consisted of three white LED’s with a lamp cover, a light guide plate, and a reflection film. When there was no pattern on the entrance side surface of the LGP, the illuminance uniformity was sensitively dependent on the distance d between the LED and the entrance surface. The illuminance uniformity increased with d but its increasing rate slowed down when d was beyond ~ 1.5 mm. When micro-patterns such as a lenticular lens array (LLA) or a serration pattern were formed on the entrance surface, the illuminance uniformity was improved substantially even for the case of very small d. At the same simulation condition, the lightguide with serration pattern showed a better uniformity than that with LLA pattern. Additional improvement could be achieved by changing the refractive index of the micro-patterns. These results suggest that using micro-patterns is a very effective way to reduce the bright spots due to their refracting function for the concentrated incident rays onto the LGP.