Showing papers in "Photonic Sensors in 2016"
TL;DR: In this paper, a hexagonal photonic crystal fiber (H-PCF) structure with high relative sensitivity for liquid sensing was proposed, in which both core and cladding are microstructures.
Abstract: This paper proposes a hexagonal photonic crystal fiber (H-PCF) structure with high relative sensitivity for liquid sensing; in which both core and cladding are microstructures. Numerical investigation is carried out by employing the full vectorial finite element method (FEM). The analysis has been done in four stages of the proposed structure. The investigation shows that the proposed structure achieves higher relative sensitivity by increasing the diameter of the innermost ring air holes in the cladding. Moreover, placing a single channel instead of using a group of tiny channels increases the relative sensitivity effectively. Investigating the effects of different parameters, the optimized structure shows significantly higher relative sensitivity with a low confinement loss.
114 citations
TL;DR: In this article, a drawing tower grating sensor network based on ultra-weak fiber Bragg gratings (FBGs) is firstly proposed and demonstrated, which is very promising for the large-scale sensing network.
Abstract: This paper reviews the work on huge capacity fiber-optic sensing network based on ultra-weak draw tower gratings developed at the National Engineering Laboratory for Fiber Optic Sensing Technology (NEL-FOST), Wuhan University of Technology, China. A versatile drawing tower grating sensor network based on ultra-weak fiber Bragg gratings (FBGs) is firstly proposed and demonstrated. The sensing network is interrogated with time- and wavelength-division multiplexing method, which is very promising for the large-scale sensing network.
37 citations
TL;DR: A curvature sensor based on an Fabry-Perot (FP) interferometer was proposed in this article, where a capillary silica tube was fusion spliced between two single mode fibers, producing an FP cavity.
Abstract: A curvature sensor based on an Fabry-Perot (FP) interferometer was proposed. A capillary silica tube was fusion spliced between two single mode fibers, producing an FP cavity. Two FP sensors with different cavity lengths were developed and subjected to curvature and temperature. The FP sensor with longer cavity showed three distinct operating regions for the curvature measurement. Namely, a linear response was shown for an intermediate curvature radius range, presenting a maximum sensitivity of 68.52 pm/m-1. When subjected to temperature, the sensing head produced a similar response for different curvature radii, with a sensitivity varying from 0.84 pm/°C to 0.89 pm/°C, which resulted in a small cross-sensitivity to temperature when the FP sensor was subjected to curvature. The FP cavity with shorter length presented low sensitivity to curvature.
36 citations
TL;DR: In this paper, the authors proposed and simulated a pressure sensor based on two-dimensional photonic crystal with high quality factor and sensitivity, which is formed by the coupling of two photonic laser based waveguides and one nanocavity.
Abstract: In this paper, we propose and simulate a pressure sensor based on two-dimensional photonic crystal with the high quality factor and sensitivity. The sensor is formed by the coupling of two photonic crystal based waveguides and one nanocavity. The photonic crystal with the triangular lattice is composed of GaAs rods. The detailed structures of the waveguides and nanocavity are optimized to achieve better quality factor and sensitivity of the sensor. For the optimized structures, the resonant wavelength of the sensor has a linear redshift as increasing the applied pressure in the range of 0–2 GPa, and the quality factor keeps unchanged nearly. The optimized quality factor is around 1500, and the sensitivity is up to 13.9 nm/GPa.
29 citations
TL;DR: In this article, two types of carbon nanotubes (SWCNTs and MWCNTs) are deposited on porous silicon by the drop casting technique, and the sensitivity response results show that the SWCNT's sensitivity reaches to 79.8%, while MWC NTs' sensitivity is 59.6%.
Abstract: Two types of carbon nanotubes [single walled nanotubes (SWCNTs) and multi walled carbon nanotubes (MWCNTs)] are deposited on porous silicon by the drop casting technique. Upon exposure to test gas mixing ratio 3% NO2, the sensitivity response results show that the SWCNTs’ sensitivity reaches to 79.8%, where MWCNTs’ is 59.6%. The study shows that sensitivity response of the films increases with an increase in the operating temperature up to 200° and 150° for MWCNTs and SWCNTs. The response and recovery time is about 19 s and 54 s at 200° for MWCNTs, respectively, and 20 s and 56 s at 150° for SWCNTs.
24 citations
TL;DR: In this article, an architecture of the sensor optical passive network (SPON), by employing hybrid wavelength division multiplexing/time division multipleXing (WDM/TDM) techniques similar to the fiber communication passive optical network (PON), is proposed.
Abstract: The recent research progress in the key device and technology of the fiber optic sensor network (FOSN) is introduced in this paper. An architecture of the sensor optical passive network (SPON), by employing hybrid wavelength division multiplexing/time division multiplexing (WDM/TDM) techniques similar to the fiber communication passive optical network (PON), is proposed. The network topology scheme of a hybrid TDM/WDM/FDM (frequency division multiplexing) three-dimension fiber optic sensing system for achieving ultra-large capacity, long distance, and high resolution sensing performance is performed and analyzed. As the most important device of the FOSN, several kinds of light source are developed, including the wideband multi-wavelength fiber laser operating at C band, switchable and tunable 2 μm multi-wavelength fiber lasers, ultra-fast mode-locked fiber laser, as well as the optical wideband chaos source, which have very good application prospects in the FOSN. Meanwhile, intelligent management techniques for the FOSN including wideband spectrum demodulation of the sensing signals and real-time fault monitoring of fiber links are presented. Moreover, several typical applications of the FOSN are also discussed, such as the fiber optic gas sensing network, fiber optic acoustic sensing network, and strain/dynamic strain sensing network.
21 citations
TL;DR: In this paper, a hybrid phase-sensitive optical time domain reflectometry (Φ-OTDR) and Brillouin optical time-domain reflectometry system which can realize simultaneous measurement of both dynamic vibration and static strain is proposed.
Abstract: A hybrid phase-sensitive optical time domain reflectometry (Φ-OTDR) and Brillouin optical time domain reflectometry (B-OTDR) system which can realize simultaneous measurement of both dynamic vibration and static strain is proposed. Because the Rayleigh scattering light and spontaneous Brilliouin scattering light are naturally frequency-multiplexed, the heterodyne asynchronous demodulation of frequency shift keying (FSK) in optical fiber communications is utilized, and the demodulations of the two scattering signals are synchronized. In addition, the forward Raman amplification is introduced to the system, which not only makes up for the deficiency of spontaneous Brilliouin scattering based distributed fiber sensor, but also has the merit of the single end measurement of B-OTDR. The designed Φ/B-OTDR hybrid system has the sensing range of 49 km with 10 m spatial resolution. The vibration and strain experiments show that this hybrid system has great potential for use in long-distance structural health monitoring.
18 citations
TL;DR: In this article, a trace-to-trace correlation coefficient is introduced to quantify intensity fluctuation of optical-time domain reflectometry traces and stability of the sensor system theoretically and experimentally.
Abstract: In a phase-sensitive optical-time domain reflectometry (Φ-OTDR) system, the challenge for dynamic strain measurement lies in large intensity fluctuations from trace to trace. The intensity fluctuation caused by stochastic characteristics of Rayleigh backscattering sets detection limit for the minimum strength of vibration measurement and causes the large measurement uncertainty. Thus, a trace-to-trace correlation coefficient is introduced to quantify intensity fluctuation of Φ-OTDR traces and stability of the sensor system theoretically and experimentally. A novel approach of measuring dynamic strain induced by various driving voltages of lead zirconate titanate (PZT) in Φ-OTDR is also demonstrated. Piezoelectric vibration signals are evaluated through analyzing peak values of fast Fourier transform spectra at the fundamental frequency and high-order harmonics based on Bessel functions. High trace-to-trace correlation coefficients varying from 0.824 to 0.967 among 100 measurements are obtained in experimental results, showing the good stability of our sensor system, as well as small uncertainty of measured peak values.
14 citations
TL;DR: In this article, a low-cost and portable optical chemical sensor based ammonia sensing system that is capable of detecting dissolved ammonia up to 5 ppm is presented, which operates without the requirement of laboratory instruments that makes it cost effective and highly portable.
Abstract: A low-cost and portable optical chemical sensor based ammonia sensing system that is capable of detecting dissolved ammonia up to 5 ppm is presented. In the system, an optical chemical sensor is designed and fabricated for sensing dissolved ammonia concentrations. The sensor uses eosin as the fluorescence dye which is immobilized on the glass substrate by a gas-permeable protection layer. A compact module is developed to hold the optical components, and a battery powered micro-controller system is designed to read out and process the data measured. The system operates without the requirement of laboratory instruments that makes it cost effective and highly portable. Moreover, the calculated results in the system can be transmitted to a PC wirelessly, which allows the remote and real-time monitoring of dissolved ammonia.
12 citations
TL;DR: In this article, the effect of an erbium-doped fiber amplifier (EDFA) placed inside the fiber ring of a cavity ring down (CRD) configuration is studied.
Abstract: The effect of an erbium-doped fiber amplifier (EDFA) placed inside the fiber ring of a cavity ring down (CRD) configuration is studied. The limitations and advantages of this configuration are discussed, and the study of the ring-down time as a function of the current applied and gain to the EDFA is also presented. In this case, the power fluctuations in the output signal are strongly dependent on the cavity ring-down time with the EDFA gain.
11 citations
TL;DR: In this article, the proposed method can be divided into two parts, constant false alarm rate (CFAR) and dilation and erosion (DE), which are applied to eliminate noises, and the latter is to remove interferences.
Abstract: Optical fiber pre-warning system (OFPS) is widely utilized in pipeline transport fields. The intrusions of OFPS need to be located. In this system, the original signals consist of noises, interferences, and intrusion signals. Here, noises are background and harmless interferences possessing with high power, and the intrusion signals are the main target of detection in this system. Hence, the study stresses on extracting the intrusion signals from the total ones. The proposed method can be divided into two parts, constant false alarm rate (CFAR) and dilation and erosion (DE). The former is applied to eliminate noises, and the latter is to remove interferences. According to some researches, the feature of noise background accords with the CFAR spatial detection. Furthermore, the detection results after CFAR can be presented as a binary image of time and space. Besides, interferences are relatively disconnected. Consequently, they can be eliminated by DE which is introduced from the image processing. To sum up, this novel method is based on CFAR and DE which can eliminate noises and interferences effectively. Moreover, it performs a brilliant detection performance. A series of tests were developed in Men Tou Gou of Beijing, China, and the reliability of proposed method can be verified by these tests.
TL;DR: In this paper, a combination of segmented unwrapping algorithm, averaging estimation of phase difference, and infinite impulse response (IIR) filtering method was proposed to enhance the signal-to-noise-ratio of a distributed acoustic sensing system based on phase-sensitive optical time-domain reflectometry (Φ-OTDR).
Abstract: In order to enhance the signal-to-noise-ratio of a distributed acoustic sensing system based on phase-sensitive optical time-domain reflectometry (Φ-OTDR), we have proposed a combination of segmented unwrapping algorithm, averaging estimation of phase difference, and infinite impulse response (IIR) filtering method. The enhancement of signal quality is numerically demonstrated. Moreover, we have studied the influence resulted from the light source noise on the Φ-OTDR performance. The result has shown that when the linewidth of light source used in the Φ-OTDR system is narrower, the performance of the system is better. In a word, such a Φ-OTDR system could obtain higher quality demodulated signals when the narrower linewidth light source is chosen and the method of averaging estimation phase difference is used.
TL;DR: In this article, a flip-flop structure using polarization switch (PSW) based on polarization rotation effect of SOA is presented, which can be used for all-optical signal processing.
Abstract: The semiconductor optical amplifier (SOA) has obvious advantages in all-optical signal processing, because of the simple structure, strong non-linearity, and easy integration. A variety of all-optical signal processing functions, such as all-optical wavelength conversion, all-optical logic gates and all-optical sampling, can be completed by SOA. So the SOA has been widespread concerned in the field of all-optical signal processing. Recently, the polarization rotation effect of SOA is receiving considerable interest, and many researchers have launched numerous research work utilizing this effect. In this paper, a new all-optical flip-flop structure using polarization switch (PSW) based on polarization rotation effect of SOA is presented.
TL;DR: In this paper, the authors proposed and analyzed the characteristics of a fiber optic optrode relying on plasmonic interaction, and showed that the combination of a silver inner layer with a dielectric titanium oxide layer with tuned thicknesses enables sensitive phase reading and allows the operation of the fiber optic sensor in the third telecommunication wavelength window.
Abstract: Optical fiber optrodes are attractive sensing devices due to their ability to perform point measurement in remote locations. Mostly, they are oriented to biochemical sensing, quite often supported by fluorescent and spectroscopic techniques, but with the refractometric approach considered as well when the objective is of high measurement performance, particularly when the focus is on enhancing the measurand resolution. In this work, we address this subject, proposing and analyzing the characteristics of a fiber optic optrode relying on plasmonic interaction. A linearly tapered optical fiber tip is covered by a double overlay: the inner one–a silver thin film and over it–a dielectric layer, with this combination allowing to achieve, at a specific wavelength range, surface plasmonic resonance (SPR) interaction sensitive to the refractive index of the surrounding medium. Typically, the interrogation of the SPR sensing structures is performed, considering spectroscopic techniques, but in principle, a far better performance can be obtained, considering the reading of the phase of the light at a specific wavelength located within the spectral plasmonic resonance. This is the approach which is studied here in the context of the proposed optical fiber optrode configuration. The analysis performed shows the combination of a silver inner layer with a dielectric titanium oxide layer with tuned thicknesses enables sensitive phase reading and allows the operation of the fiber optic optrode sensor in the third telecommunication wavelength window.
TL;DR: In this paper, the frequency response of a dual depletion p-i-n (PIN) photodiode structure is investigated, where the light is incident on the N side and the drift region is located between the N contact and the absorption region.
Abstract: The frequency response of a dual depletion p-i-n (PIN) photodiode structure is investigated. It is assumed that the light is incident on the N side and the drift region is located between the N contact and the absorption region. The numerical model takes into account the transit time and the capacitive effects and is applied to photodiodes with non-uniform illumination and linear electric field profile. With an adequate choice of the device’s structural parameters, dual depletion photodiodes can have larger bandwidths than the conventional PIN devices.
TL;DR: In this paper, the response of fiber Bragg gratings (FBGs) subjected to the ultrasonic wave has been theoretically and experimentally investigated, and the results of this analysis provide useful tools for high sensitivity ultrasound detection in damage detection systems.
Abstract: In this paper, the response of fiber Bragg gratings (FBGs) subjected to the ultrasonic wave has been theoretically and experimentally investigated. Although FBG sensors have been widely used in the ultrasonic detection for practical structural health monitoring, the relationship between the grating length and ultrasonic frequency is not yet to be obtained. To address this problem, an ultrasound detection system based on FBGs is designed and the response sensitivity of different lengths gratings are detected. Experimental results indicate that the grating with 3 mm length has a higher sensitivity when detecting high frequency ultrasonic wave, and the amplitude can be up to 0.6 mV. The 10 mm length grating has better detection sensitivity for low frequency ultrasonic wave and the amplitude is 0.8 mV. The results of this analysis provide useful tools for high sensitivity ultrasound detection in damage detection systems.
TL;DR: The principle and configuration of laser triangulation are introduced and, based on this technology, the pavement roughness of a road surface is measured.
Abstract: Pavement roughness is one of the most important factors for appraising highway construction. In this paper, we choose the laser triangulation to measure pavement roughness. The principle and configuration of laser triangulation are introduced. Based on this technology, the pavement roughness of a road surface is measured. The measurement results are given in this paper. The measurement range of this system is 50 μm. The measurement error of this technology is analyzed. This technology has an important significance to appraise the quality of highway after completion of the workload.
TL;DR: In this paper, the electromagnetic pulses due to laser-target interaction in laser facility had been evaluated using a cone antenna in the microwave in frequencies ranging from several hundreds of MHz to 2 GHz, when long-pulse lasers with several thousands of joules illuminated the solid targets, meanwhile the voltage signals from 1 V to 4 V were captured as functions of laser energy and backlight laser, where the corresponding electric field strengths were obtained by simulating the cone antenna and conducting a mathematical process (Tiknohov Regularization with L curve).
Abstract: Emission of the electromagnetic pulses (EMP) due to laser-target interaction in laser facility had been evaluated using a cone antenna in this work. The microwave in frequencies ranging from several hundreds of MHz to 2 GHz was recorded when long-pulse lasers with several thousands of joules illuminated the solid targets, meanwhile the voltage signals from 1 V to 4 V were captured as functions of laser energy and backlight laser, where the corresponding electric field strengths were obtained by simulating the cone antenna in combination with conducting a mathematical process (Tiknohov Regularization with L curve). All the typical coupled voltage oscillations displayed multiple peaks and had duration of up to 80 ns before decaying into noise and mechanisms of the EMP generation was schematically interpreted in basis of the practical measuring environments. The resultant data were expected to offer basic know-how to achieve inertial confinement fusion.
TL;DR: In this paper, a multichannel heterodyne fiber optic vibrometer is demonstrated which can be operated at ranges in excess of 50 m. The system is designed to measure periodic signals, impacts, rotation, 3D strain, and vibration mapping.
Abstract: A multichannel heterodyne fiber optic vibrometer is demonstrated which can be operated at ranges in excess of 50 m. The system is designed to measure periodic signals, impacts, rotation, 3D strain, and vibration mapping. The displacement resolution of each channel exceeds 1 nm. The outputs from all channels are simultaneous, and the number of channels can be increased by using optical switches.
TL;DR: In this article, a 2×2 optical waveguide coupler at 850 nm based on the multimode interference (MMI) structure with the polysilsesquioxanes liquid series (PSQ-Ls) polymer material and the imprint technique is presented.
Abstract: A 2×2 optical waveguide coupler at 850 nm based on the multimode interference (MMI) structure with the polysilsesquioxanes liquid series (PSQ-Ls) polymer material and the imprint technique is presented. The influence of the structural parameters, such as the single mode condition, the waveguide spacing of input/output ports, and the width and length of the multimode waveguide, on the optical splitting performance including the excess loss and the uniformity is simulated by the beam propagation method. By inserting a taper section of isosceles trapezoid between the single mode and multimode waveguides, the optimized structural parameters for low excess loss and high uniformity are obtained with the excess loss of‒0.040 dB and the uniformity of‒0.007 dB. The effect of the structure deviations induced during the imprint process on the optical splitting performance at different residual layer thicknesses is also investigated. The analysis results provide useful instructions for the waveguide device fabrication.
TL;DR: In this article, a miniature fiber-optic Fabry-Perot interferometer (MOFPI) fabricated by splicing a hollow silica tube (HST) with inner diameter of 4 µm to the end of a singlemode fiber is investigated and experimentally demonstrated.
Abstract: A miniature fiber-optic Fabry-Perot interferometer (MOFPI) fabricated by splicing a hollow silica tube (HST) with inner diameter of 4 µm to the end of a single-mode fiber is investigated and experimentally demonstrated. The theoretical relationship between the free spectrum range and the length of HST is verified by fabricating several MOFPIs with different lengths. We characterize the MOFPIs for temperature, liquid refractive index, and strain. Experimental results show that the sensitivities of the temperature, liquid refractive index, and strain are 16.42 pm/°C,–118.56 dB/RIU, and 1.21 pm/µe, respectively.
TL;DR: In this article, an ultra-compact water temperature sensor was designed by using the photonic crystal technology on the InP substrate at the 1.55-μm wavelength window.
Abstract: We design an ultra-compact water temperature sensor by using the photonic crystal technology on the InP substrate at the 1.55-μm wavelength window. The photonic crystal consists of rods in a hexagonal lattice and a polymethyl methacrylate (PMMA) background. By using the plane wave expansion (PWE) method, the lattice constant and radius of rods are obtained, 520 nm and 80.6 nm, respectively. With a nanocavity placed in the waveguide, a resonance peak is observed at the 1.55-μm wavelength window. Any change of the water temperature inside the nanocavity results in the shift of the resonance wavelength. Our simulations show a shift of about 11 nm for a temperature change of 22.5 ℃. The resonance wavelength has a linear relation with the water temperature.
TL;DR: In this paper, the reflective spectrum power and the bandwidth of the fiber Bragg grating (FBG) under gradient strain were investigated and experimentally demonstrated, where the gradient strain is applied on the FBG, which can induce FBG bandwidth broadening, resulting in the variation of reflective power.
Abstract: The reflective spectrum power and the bandwidth of the fiber Bragg grating (FBG) under gradient strain are researched and experimentally demonstrated. The gradient strain is applied on the FBG, which can induce FBG bandwidth broadening, resulting in the variation of reflective power. Based on the coupled-mode theory and transfer matrix method, the segmental linear relationship between the gradient strain, the reflective power, and the bandwidth is simulated and analyzed, and the influence of the FBG length on the reflective spectrum is analyzed. In the experiment, the strict gradient stain device is designed; the experimental results indicate that the reflective optic power and the bandwidth of the FBG under gradient stain are concerned with the length of the FBG. Experimental results are well consistent with the theoretical analysis, which have important guiding significance in the FBG dynamic sensing.
TL;DR: In this paper, a cost-effective precision fiber Bragg grating (FBG) interrogation system using long-wavelength vertical-cavity surface-emitting laser (VCSEL) is presented.
Abstract: This paper presents the development of a cost-effective precision fiber Bragg grating (FBG) interrogation system using long-wavelength vertical-cavity surface-emitting laser (VCSEL). Tuning properties of a long-wavelength VCSEL have been studied experimentally. An approximately quadratic dependence of its wavelength on the injection current has been observed. The overall design and key operations of this system including intensity normalization, peak detection, and quadratic curve fitting are introduced in detail. The results show that the system achieves an accuracy of 1.2 pm with a tuning range of 3 nm and a tuning rate of 1 kHz. It is demonstrated that this system is practical and effective by applied in the FBG transformer temperature monitoring.
TL;DR: Experimental results show that the presented deformation measurement system (CDMS) based on inertial platform is feasible, practical, and reliable; the system can accurately and quickly locate the maximum deformation and has extensive and broad application prospects.
Abstract: Bridge is an important part of modern transportation systems and deformation is a key index for bridge’s safety evaluation. To achieve the long span bridge curve measurement rapidly and timely and accurately locate the bridge maximum deformation, the continuous deformation measurement system (CDMS) based on inertial platform is presented and validated in this paper. Firstly, based on various bridge deformation measurement methods, the method of deformation measurement based on the fiber optic gyro (FOG) is introduced. Secondly, the basic measurement principle based on FOG is presented and the continuous curve trajectory is derived by the formula. Then the measurement accuracy is analyzed in theory and the relevant factors are presented to ensure the measurement accuracy. Finally, the deformation measurement experiments are conducted on a bridge across the Yangtze River. Experimental results show that the presented deformation measurement method is feasible, practical, and reliable; the system can accurately and quickly locate the maximum deformation and has extensive and broad application prospects.
TL;DR: In this article, the effect of thermal annealing on the characteristics of silicon homojunction photodetector was studied and the electrical and spectral properties of this photoder were determined and optimized before and after the annealation process.
Abstract: In this work, the effect of thermal annealing on the characteristics of silicon homojunction photodetector was studied. This homojunction photodetector was fabricated by means of plasma-induced etching of p-type silicon substrate and plasma sputtering of n-type silicon target in vacuum. The electrical and spectral characteristics of this photodetector were determined and optimized before and after the annealing process. The maximum surface reflectance of 1.89% and 1.81%, the maximum responsivity of 0.495 A/W and 0.55 A/W, the ideality factor of 1.80 and 1.99, the maximum external quantum efficiency of 76% and 83.5%, and the built-in potential of 0.79 V and 0.72 V were obtained before and after annealing, respectively.
TL;DR: In this paper, a novel variety of three dimensional (3D) vibration sensor based on chirped fiber Bragg grating (CFBG) is developed to measure 3D vibration in the mechanical equipment field.
Abstract: A novel variety of three dimensional (3D) vibration sensor based on chirped fiber Bragg grating (CFBG) is developed to measure 3D vibration in the mechanical equipment field. The sensor is composed of three independent vibration sensing units. Each unit uses double matched chirped gratings as sensing elements, and the sensing signal is processed by the edge filtering demodulation method. The structure and principle of the sensor are theoretically analyzed, and its performances are obtained from some experiments and the results are as follows: operating frequency range of the sensor is 10 Hz‒500 Hz; acceleration measurement range is 2 m·s-2‒30 m·s-2; sensitivity is about 70 mV/m·s-2; crosstalk coefficient is greater than 22 dB; self-compensation for temperature is available. Eventually the sensor is applied to monitor the vibration state of radiation pump. Seen from its experiments and applications, the sensor has good sensing performances, which can meet a certain requirement for some engineering measurement.
TL;DR: In this article, an optical fiber temperature sensor made of a compound of epoxy and optical glass particles was developed and evaluated by the ratio of the transmitted intensity of two different light-emitting diodes (LED) with a wavelength of 460 nm and 650 nm.
Abstract: This paper describes the development and function of an optical fiber temperature sensor made out of a compound of epoxy and optical glass particles. Because of the different thermo-optic coefficients of these materials, this compound exhibits a strong wavelength and temperature dependent optical transmission, and it therefore can be employed for fiber optic temperature measurements. The temperature at the sensor, which is integrated into a polymer optical fiber (POF), is evaluated by the ratio of the transmitted intensity of two different light-emitting diodes (LED) with a wavelength of 460 nm and 650 nm. The material characterization and influences of different sensor lengths and two particle sizes on the measurement result are discussed. The temperature dependency of the transmission increases with smaller particles and with increasing sensor length. With glass particles with a diameter of 43 μm and a sensor length of 9.8 mm, the intensity ratio of the two LEDs decreases by 60% within a temperature change from 10°C to 40°C.
TL;DR: In this article, a new technique for flat optical frequency comb (OFC) generation is presented, which is based on the nonlinear process of multiple four-wave mixing (FWM) effects.
Abstract: This paper presents a new technique for flat optical frequency comb (OFC) generation, which is based on the nonlinear process of multiple four-wave mixing (FWM) effects. The nonlinear effects are significantly enhanced by using the proposed optical feedback scheme consisting of a single mode fiber (SMF), two highly nonlinear fibers (HNLFs) with different zero dispersion wavelengths (ZDWs) and polarization beam splitters (PBSs). Simulation results illustrate its efficiency and applicability of expanding a comb to 128 coherent lines spaced by only 20 GHz within 6-dB power deviation.
TL;DR: High-speed multi-wavelength photoacoustic/photothermal flow cytometry for in vivo CBV assessment with multiple dyes as PA contrast agents (labels) is proposed and the capability of this technique to monitor the clearance of three dyes in an animal model is characterized.
Abstract: The measurement of circulating blood volume (CBV) is crucial in various medical conditions including surgery, iatrogenic problems, rapid fluid administration, transfusion of red blood cells, or trauma with extensive blood loss including battlefield injuries and other emergencies. Currently, available commercial techniques are invasive and time-consuming for trauma situations. Recently, we have proposed high-speed multi-wavelength photoacoustic/photothermal (PA/PT) flow cytometry for in vivo CBV assessment with multiple dyes as PA contrast agents (labels). As the first step, we have characterized the capability of this technique to monitor the clearance of three dyes (indocyanine green, methylene blue, and trypan blue) in an animal model. However, there are strong demands on improvements in PA/PT flow cytometry. As additional verification of our proof-of-concept of this technique, we performed optical photometric CBV measurements in vitro. Three label dyes—methylene blue, crystal violet and, partially, brilliant green—were selected for simultaneous photometric determination of the components of their two-dye mixtures in the circulating blood in vitro without any extra data (like hemoglobin absorption) known a priori. The tests of single dyes and their mixtures in a flow system simulating a blood transfusion system showed a negligible difference between the sensitivities of the determination of these dyes under batch and flow conditions. For individual dyes, the limits of detection of 3×10–6 M‒3×10–6 M in blood were achieved, which provided their continuous determination at a level of 10–5 M for the CBV assessment without a priori data on the matrix. The CBV assessment with errors no higher than 4% were obtained, and the possibility to apply the developed procedure for optical photometric (flow cytometry) with laser sources was shown.