Journal ArticleDOI
Measurement and multi-response optimization of turning parameters for magnesium alloy using hybrid combination of Taguchi-GRA-PCA technique
Reads0
Chats0
TLDR
In this article, the cutting force (Fz), material removal rate (MRR), tool flank wear (VB) and surface roughness (Ra) in turning of magnesium alloy with PVD-coated carbide insert in dry conditions were investigated.About:
This article is published in Measurement.The article was published on 2020-07-15. It has received 64 citations till now. The article focuses on the topics: Taguchi methods & Magnesium alloy.read more
Citations
More filters
Journal ArticleDOI
A Review of Indirect Tool Condition Monitoring Systems and Decision-Making Methods in Turning: Critical Analysis and Trends.
Mustafa Kuntoğlu,Abdullah Aslan,Danil Yurievich Pimenov,Üsame Ali Usca,Emin Salur,Munish Kumar Gupta,Munish Kumar Gupta,Tadeusz Mikolajczyk,Khaled Giasin,Wojciech Kapłonek,Shubham Sharma +10 more
TL;DR: In this paper, the effect of sensorial data on tool wear by considering previous published papers is discussed, and the main aim is to discuss the impact of sensual data on tools' wear and surface roughness.
Journal ArticleDOI
Investigation of signal behaviors for sensor fusion with tool condition monitoring system in turning
Mustafa Kuntoğlu,Haci Saglam +1 more
TL;DR: Monitoring of the cutting area with different type of sensors requires confirmation for composing sensor fusion to obtain longer tool life and high-quality product to enable more reliable, robust and consistent machining.
Journal ArticleDOI
Optimization and Analysis of Surface Roughness, Flank Wear and 5 Different Sensorial Data via Tool Condition Monitoring System in Turning of AISI 5140.
Mustafa Kuntoğlu,Abdullah Aslan,Haci Saglam,Danil Yurievich Pimenov,Khaled Giasin,Tadeusz Mikolajczyk +5 more
TL;DR: This study investigates the optimization of five different sensorial criteria, additional to tool wear (VB) and surface roughness (Ra), via the Tool Condition Monitoring System (TCMS) for the first time in the open literature.
Journal ArticleDOI
Influence of Fiber Volume and Fiber Length on Thermal and Flexural Properties of a Hybrid Natural Polymer Composite Prepared with Banana Stem, Pineapple Leaf, and S-Glass
K.B. Prakash,Yahya Ali Fageehi,Rajasekaran Saminathan,P. Manoj Kumar,S. S. Saravanakumar,Ram Subbiah,B. Arulmurugan,S. Rajkumar +7 more
TL;DR: In this paper, the changes in the thermal properties and mechanical properties of S-glass reinforced with a sodium hydroxide-treated pineapple leaf (PALF) and banana stem fibers were studied.
Journal ArticleDOI
Experimental investigation on EDM of Si3N4–TiN using grey relational analysis coupled with teaching-learning-based optimization algorithm
TL;DR: In this paper, the optimal EDM parameters based on GRA and TOPSIS methods for obtaining better responses are current-10amps, pulse-on time - 8μsec; pulse-off time - 4μsec, dielectric pressure - 20 kg/cm2 and spark gap voltage - 32 V.
References
More filters
Journal ArticleDOI
Protective coatings on magnesium and its alloys — a critical review
J.E. Gray,B. Luan +1 more
TL;DR: In this paper, the state of the art in coating and surface modification technologies, applied to magnesium-based substrates for improved corrosion and wear resistance, are discussed, including electrochemical plating, conversion coatings, anodizing, gas phase deposition processes, laser surface alloying/cladding and organic coatings.
Book
Light Alloys: From Traditional Alloys to Nanocrystals
TL;DR: In this article, the physical metallurgy of aluminium alloys is discussed, and the following materials and processing methods are presented: Alloy Alloy Alloys, Alloy Alloy Alloy Materials and Processing Methods.
Journal ArticleDOI
Experimental investigations of cutting parameters influence on cutting forces and surface roughness in finish hard turning of MDN250 steel
TL;DR: In this paper, the effect of cutting parameters (cutting speed, feed rate and depth of cut) on cutting forces and surface roughness in finish hard turning of MDN250 steel (equivalent to 18Ni(250) maraging steel) using coated ceramic tool.
Journal ArticleDOI
Optimization of surface roughness and flank wear using the Taguchi method in milling of Hadfield steel with PVD and CVD coated inserts
TL;DR: In this article, the Taguchi method and regression analysis have been applied to evaluate the machinability of Hadfield steel with PVD TiAlN- and CVD TiCN/Al 2 O 3 -coated carbide inserts under dry milling conditions.
Journal ArticleDOI
Analysis of surface roughness and cutting force components in hard turning with CBN tool: Prediction model and cutting conditions optimization
TL;DR: In this paper, the effects of cutting speed, feed rate, workpiece hardness and depth of cut on surface roughness and cutting force components in the hard turning were experimentally investigated.
Related Papers (5)
Investigation of progressive tool wear for determining of optimized machining parameters in turning
Mustafa Kuntoğlu,Haci Saglam +1 more
Optimization and analysis of process parameters for flank wear, cutting forces and vibration in turning of AISI 5140: A comprehensive study
Multi-objective optimisation of EDM process using hybrid Taguchi-based methodologies for Ti-6Al-4V alloy
Manisha Priyadarshini,Kamal Pal +1 more