Nuclear materials and energy 

About: Nuclear materials and energy is an academic journal published by Elsevier BV. The journal publishes majorly in the area(s): Divertor & Tungsten. It has an ISSN identifier of 2352-1791. It is also open access. Over the lifetime, 1330 publications have been published receiving 12161 citations.

Physics basis for the first ITER tungsten divertor

Abstract: On the eve of component procurement, this paper discusses the present physics basis for the first ITER tungsten (W) divertor, beginning with a reminder of the key elements defining the overall design, and outlining relevant aspects of the Research Plan accompanying the new “staged approach” to ITER nuclear operations which fixes the overall divertor lifetime constraint. The principal focus is on the main design driver, steady state power fluxes in the DT phases, obtained from simulations using the 2-D SOLPS-4.3 and SOLPS-ITER plasma boundary codes, assuming the use of the low Z seeding impurities nitrogen (N) and neon (Ne). A new perspective on the simulation database is adopted, concentrating purely on the divertor physics aspects rather than on the core-edge integration, which has been studied extensively in the course of the divertor design evolution and is published elsewhere. Emphasis is placed on factors which may increase the peak steady state loads: divertor target shaping for component misalignment protection, the influence of fluid drifts, and the consequences of narrow scrape-off layer heat flux channels. All tend to push the divertor into an operating space at higher sub-divertor neutral pressure in order to remain at power flux densities acceptable for the target material. However, a revised criterion for the maximum tolerable loads based on avoidance of W recrystallization, sets an upper limit potentially ∼50% higher than the previously accepted value of ∼10 MW m−2, a consequence both of the choice of material and the finalized component design. Although the simulation database is currently restricted to the 2-D toroidally symmetric situation, considerable progress is now also being made using the EMC3-Eirene 3-D code suite for the assessment of power loading in the presence of magnetic perturbations for ELM control. Some new results for low input power corresponding to the early H-mode operation phases are reported, showing that even if realistic plasma screening is taken into account, significant asymmetric divertor heat fluxes may arise far from the unperturbed strike point. The issue of tolerable limits for transient heat pulses is an open and key question. A new scaling for ELM power deposition has shown that whilst there may be more latitude for operation at higher current without ELM control, the ultimate limit is likely to be set more by material fatigue under large numbers of sub-threshold melting events.

Use of Tungsten Material for the ITER Divertor

Abstract: Since the ITER divertor design includes tungsten monoblocks in the vertical target where heat loads are maximal, the design to protect leading edges as well as technology R&D for high performance armor-heat sink joint were necessary to be implemented. In the R&D, the availability of the technology was demonstrated by high heat flux test of tungsten monoblock components. Not systematically but frequently macro-cracks appeared at the middle of monoblocks after 20 MW/m2 loading. The initiation of such macro-cracks was considered to be due to cyclic exposure to high temperature, ∼2000 °C, where creep, recrystallization and low cycle fatigue were concerned. To understand correlation between the macro-crack appearance and mechanical properties and possible update of acceptance criteria in the material specification, an activity to characterize the tungsten monoblocks was launched.

European DEMO divertor target: Operational requirements and material-design interface

Abstract: Recently, an integrated program of conceptual design activities for the European DEMO reactor was launched in the framework of the EUROfusion Consortium, where reliable power handling capability was identified as one of the most critical scientific as well as technological challenges for a DEMO reactor. The divertor is the key in-vessel plasma-facing component being in charge of power exhaust and removal of impurity particles. The DEMO divertor target will have to withstand extreme thermal loads where the local peak heat flux is expected to reach up to 20 MW/m2 during slow transient events in DEMO. To assure sufficient heat removal capability of the divertor target against normal and transient operational scenarios under expected cumulative neutron dose of up to 13 dpa is one of the fundamental engineering challenges imposed on target design. To develop the design of the DEMO divertor and related technologies, an R&D work package ‘Divertor’ has been set up in this consortium. The subproject ‘Target Development’ is devoted to the development of the conceptual design and the core technologies of the plasma-facing target. Devising and implementing novel structural heat sink materials (e.g. W/Cu composites) to advanced target design concepts is one of the major objectives of this subproject. In this paper, the underlying design requirements imposed by the envisaged power exhaust goal and the prominent material-design interface issues are discussed. In addition, the candidate design concepts being currently considered are presented together with the related material issues. Finally, the first results achieved so far are presented.

Physics conclusions in support of ITER W divertor monoblock shaping

Abstract: The key remaining physics design issue for the ITER tungsten (W) divertor is the question of monoblock (MB) front surface shaping in the high heat flux target areas of the actively cooled targets. Engineering tolerance specifications impose a challenging maximum radial step between toroidally adjacent MBs of 0.3 mm. Assuming optical projection of the parallel heat loads, magnetic shadowing of these edges is required if quasi-steady state melting is to be avoided under certain conditions during burning plasma operation and transiently during edge localized mode (ELM) or disruption induced power loading. An experiment on JET in 2013 designed to investigate the consequences of transient W edge melting on ITER, found significant deficits in the edge power loads expected on the basis of simple geometric arguments, throwing doubt on the understanding of edge loading at glancing field line angles. As a result, a coordinated multi-experiment and simulation effort was initiated via the International Tokamak Physics Activity (ITPA) and through ITER contracts, aimed at improving the physics basis supporting a MB shaping decision from the point of view both of edge power loading and melt dynamics. This paper reports on the outcome of this activity, concluding first that the geometrical approximation for leading edge power loading on radially misaligned poloidal leading edges is indeed valid. On this basis, the behaviour of shaped and unshaped monoblock surfaces under stationary and transient loads, with and without melting, is compared in order to examine the consequences of melting, or power overload in context of the benefit, or not, of shaping. The paper concludes that MB top surface shaping is recommended to shadow poloidal gap edges in the high heat flux areas of the ITER divertor targets.

ELM divertor peak energy fluence scaling to ITER with data from JET, MAST and ASDEX upgrade

Abstract: A newly established scaling of the ELM energy fluence using dedicated data sets from JET operation with CFC & ILW plasma facing components (PFCs), ASDEX Upgrade (AUG) operation with both CFC an ...