Showing papers by "Warsaw University of Technology published in 2010"

Recent Advances and Industrial Applications of Multilevel Converters

Abstract: Multilevel converters have been under research and development for more than three decades and have found successful industrial application. However, this is still a technology under development, and many new contributions and new commercial topologies have been reported in the last few years. The aim of this paper is to group and review these recent contributions, in order to establish the current state of the art and trends of the technology, to provide readers with a comprehensive and insightful review of where multilevel converter technology stands and is heading. This paper first presents a brief overview of well-established multilevel converters strongly oriented to their current state in industrial applications to then center the discussion on the new converters that have made their way into the industry. In addition, new promising topologies are discussed. Recent advances made in modulation and control of multilevel converters are also addressed. A great part of this paper is devoted to show nontraditional applications powered by multilevel converters and how multilevel converters are becoming an enabling technology in many industrial sectors. Finally, some future trends and challenges in the further development of this technology are discussed to motivate future contributions that address open problems and explore new possibilities.

A Survey on Cascaded Multilevel Inverters

Abstract: Cascaded multilevel inverters synthesize a medium-voltage output based on a series connection of power cells which use standard low-voltage component configurations. This characteristic allows one to achieve high-quality output voltages and input currents and also outstanding availability due to their intrinsic component redundancy. Due to these features, the cascaded multilevel inverter has been recognized as an important alternative in the medium-voltage inverter market. This paper presents a survey of different topologies, control strategies and modulation techniques used by these inverters. Regenerative and advanced topologies are also discussed. Applications where the mentioned features play a key role are shown. Finally, future developments are addressed.

Elliptic Flow of Charged Particles in Pb-Pb Collisions at root s(NN)=2.76 TeV

Abstract: We report the first measurement of charged particle elliptic flow in Pb-Pb collisions at root s(NN) p = 2.76 TeV with the ALICE detector at the CERN Large Hadron Collider. The measurement is performed in the central pseudorapidity region (vertical bar eta vertical bar < 0.8) and transverse momentum range 0.2 < p(t) < 5.0 GeV/c. The elliptic flow signal v(2), measured using the 4-particle correlation method, averaged over transverse momentum and pseudorapidity is 0.087 +/- 0.002(stat) +/- 0.003(syst) in the 40%-50% centrality class. The differential elliptic flow v(2)(p(t)) reaches a maximum of 0.2 near p(t) = 3 GeV/c. Compared to RHIC Au-Au collisions at root s(NN) = 200 GeV, the elliptic flow increases by about 30%. Some hydrodynamic model predictions which include viscous corrections are in agreement with the observed increase.

SNDlib 1.0—Survivable Network Design Library

Abstract: This article describes the Survivable Network Design Library (SNDlib), a data library for fixed telecommunication network design available at . In the current version 1.0, the library contains data related to 22 networks which, combined with a set of selected planning parameters, leads to 830 network design problem instances. In this article, we discuss the data concepts of SNDlib and describe a mathematical model for each design problem considered in the library. We also provide information on characteristic features and the origin of the SNDlib problem instances. © 2009 Wiley Periodicals, Inc. NETWORKS, 2010

Electroactive materials for organic electronics: preparation strategies, structural aspects and characterization techniques

Abstract: This critical review discusses specific chemical and physicochemical requirements which must be met for organic compounds to be considered as promising materials for applications in organic electronics. Although emphasis is put on molecules and macromolecules suitable for fabrication of field effect transistors (FETs), a large fraction of the discussed compounds can also be applied in other organic or hybrid (organic–inorganic) electronic devices such as photodiodes, light emitting diodes, photovoltaic cells, etc. It should be of interest to chemists, physicists, material scientists and electrical engineers working in the domain of organic electronics (423 references).

Observation of charge-dependent azimuthal correlations and possible local strong parity violation in heavy-ion collisions

Abstract: Parity (P)-odd domains, corresponding to nontrivial topological solutions of the QCD vacuum, might be created during relativistic heavy-ion collisions. These domains are predicted to lead to charge separation of quarks along the orbital momentum of the system created in noncentral collisions. To study this effect, we investigate a three-particle mixed-harmonics azimuthal correlator which is a P-even observable, but directly sensitive to the charge-separation effect. We report measurements of this observable using the STAR detector in Au + Au and Cu + Cu collisions at root s(NN) = 200 and 62 GeV. The results are presented as a function of collision centrality, particle separation in rapidity, and particle transverse momentum. A signal consistent with several of the theoretical expectations is detected in all four data sets. We compare our results to the predictions of existing event generators and discuss in detail possible contributions from other effects that are not related to P violation.

Higher moments of net proton multiplicity distributions at RHIC.

Abstract: 200 GeV corresponding to baryon chemical potentials (mu(B)) between 200 and 20 MeV. Our measurements of the products kappa sigma(2) and S sigma, which can be related to theoretical calculations sensitive to baryon number susceptibilities and long-range correlations, are constant as functions of collision centrality. We compare these products with results from lattice QCD and various models without a critical point and study the root s(NN) dependence of kappa sigma(2). From the measurements at the three beam energies, we find no evidence for a critical point in the QCD phase diagram for mu(B) below 200 MeV.

Reduction of Fe2O3 with hydrogen

Abstract: The reduction of Fe 2 O 3 with hydrogen was studied. The thermodynamic analysis of the process implied that temperature-programmed reduction of the oxide should proceed in three steps, i.e. Fe 2 O 3 → Fe 3 O 4 → “FeO” → Fe, at X H 2 O / X H 2 ratio over 0.35, but in two steps, i.e. Fe 2 O 3 → Fe 3 O 4 → Fe, below that value. The idea was verified by TPR and XRD studies. Generally, the examinations confirmed the suggestions. The reduction is three-step reaction at high X H 2 O / X H 2 ratio, but two-step reaction at low that ratio. Additionally, it was revealed that at extremely low X H 2 O / X H 2 ratio the TP reduction is a one-step reaction, i.e. Fe 2 O 3 → Fe.

Charged-particle multiplicity measurement in proton-proton collisions at $\sqrt{s}=7$ TeV with ALICE at LHC

Abstract: Charged-particle production was studied in proton-proton collisions collected at the LHC with the ALICE detector at centre-of-mass energies 0.9 TeV and 2.36 TeV in the pseudorapidity range vertical bar eta vertical bar < 1.4. In the central region (vertical bar eta vertical bar < 0.5), at 0.9 TeV, we measure charged-particle pseudo-rapidity density dN(ch)/d eta = 3.02 +/- 0.01(stat.)(-0.05)(+0.08)(syst.) for inelastic interactions, and dN(ch)/d eta = 3.58 +/- 0.01 (stat.)(-0.12)(+0.12)(syst.) for non-single-diffractive interactions. At 2.36 TeV, we find dN(ch)/d eta = 3.77 +/- 0.01(stat.)(-0.12)(+0.25)(syst.) for inelastic, and dN(ch)/d eta = 4.43 +/- 0.01(stat.)(-0.12)(+0.17)(syst.) for non-single-diffractive collisions. The relative increase in charged-particle multiplicity from the lower to higher energy is 24.7% +/- 0.5%(stat.)(-2.8)(+5.7)%(syst.) for inelastic and 23.7% +/- 0.5%(stat.)(-1.1)(+4.6)%(syst.) for non-single-diffractive interactions. This increase is consistent with that reported by the CMS collaboration for non-single-diffractive events and larger than that found by a number of commonly used models. The multiplicity distribution was measured in different pseudorapidity intervals and studied in terms of KNO variables at both energies. The results are compared to proton-antiproton data and to model predictions.

Charged-Particle Multiplicity Density at Midrapidity in Central Pb-Pb Collisions at root s(NN)=2.76 TeV

Abstract: The first measurement of the charged-particle multiplicity density at midrapidity in Pb-Pb collisions at a center-of-mass energy per nucleon pair root s(NN) = 2.76 TeV is presented. For an event sample corresponding to the most central 5% of the hadronic cross section, the pseudorapidity density of primary charged particles at midrapidity is 1584 +/- 4(stat) +/- 76(syst), which corresponds to 8.3 +/- 0.4(syst) per participating nucleon pair. This represents an increase of about a factor 1.9 relative to pp collisions at similar collision energies, and about a factor 2.2 to central Au-Au collisions at root s(NN) = 0.2 TeV. This measurement provides the first experimental constraint for models of nucleus-nucleus collisions at LHC energies.

Alignment of the ALICE Inner Tracking System with cosmic-ray tracks

Abstract: ALICE (A Large Ion Collider Experiment) is the LHC (Large Hadron Collider) experiment devoted to investigating the strongly interacting matter created in nucleus-nucleus collisions at the LHC energies. The ALICE ITS, Inner Tracking System, consists of six cylindrical layers of silicon detectors with three different technologies; in the outward direction: two layers of pixel detectors, two layers each of drift, and strip detectors. The number of parameters to be determined in the spatial alignment of the 2198 sensor modules of the ITS is about 13,000. The target alignment precision is well below 10 mu m in some cases (pixels). The sources of alignment information include survey measurements, and the reconstructed tracks from cosmic rays and from proton-proton collisions. The main track-based alignment method uses the Millepede global approach. An iterative local method was developed and used as well. We present the results obtained for the ITS alignment using about 10(5) charged tracks from cosmic rays that have been collected during summer 2008, with the ALICE solenoidal magnet switched off.

Direct Power Control of Doubly-Fed-Induction-Generator-Based Wind Turbines Under Unbalanced Grid Voltage

Abstract: In this paper, the behavior of a doubly fed induction generator (DFIG) is studied under unbalanced grid voltage conditions. It is shown that if no special control efforts are employed, the behavior of the generator is deteriorated, basically due to two reasons: electromagnetic torque oscillations and nonsinusoidal current exchange with the grid. These phenomena are first analyzed theoretically as a function of the stator active and reactive instantaneous power exchange by the stator of the DFIG and the grid-side converter (GSC). This analysis provides the main ideas for generation of the active and reactive power references for the rotor-side converter (RSC) and the GSC, controlled by means of direct power control techniques. Therefore, this paper proposes a new algorithm that generates the RSC power references, without the necessity of a sequence component extraction, in order to eliminate torque oscillations and achieve sinusoidal stator currents exchange. On the contrary, the GSC power references are provided by means of voltage and current sequence extraction. Finally, simulation and experimental results successfully validate the proposed power reference generation methods.

Contactless Energy Transfer System With FPGA-Controlled Resonant Converter

Abstract: Power supply based on an inductive coupled contactless energy transfer system is presented in this paper. The energy is transferred using a rotatable transformer and a power electronic converter. To minimize total losses of the system, a series resonant compensation circuit is applied assuring zero-current switching condition for insulated-gate bipolar transistors. The analytical expression of the transfer dc voltage gain is presented and discussed. The novelty of the system lies in the application of a fully digital field-programmable-gate-array-based controller and a protection system. The resonant frequency is adjusted by a primary peak current regulator. Some simulation and experimental results illustrating the operation of the developed 3-kW 60-kHz laboratory prototype are given. Although the presented power supply with a rotatable transformer is constructed mainly for robotics and manipulators, the described design and control methodology has general validity and can be applied for a wide class of contactless power supply with core or coreless transformers.

Detection of clinically relevant exonic copy‐number changes by array CGH

Abstract: Array comparative genomic hybridization (aCGH) is a powerful tool for the molecular elucidation and diagnosis of disorders resulting from genomic copy-number variation (CNV). However, intragenic deletions or duplications--those including genomic intervals of a size smaller than a gene--have remained beyond the detection limit of most clinical aCGH analyses. Increasing array probe number improves genomic resolution, although higher cost may limit implementation, and enhanced detection of benign CNV can confound clinical interpretation. We designed an array with exonic coverage of selected disease and candidate genes and used it clinically to identify losses or gains throughout the genome involving at least one exon and as small as several hundred base pairs in size. In some patients, the detected copy-number change occurs within a gene known to be causative of the observed clinical phenotype, demonstrating the ability of this array to detect clinically relevant CNVs with subkilobase resolution. In summary, we demonstrate the utility of a custom-designed, exon-targeted oligonucleotide array to detect intragenic copy-number changes in patients with various clinical phenotypes.

Observation of an Antimatter Hypernucleus

Abstract: Nuclear collisions recreate conditions in the universe microseconds after the Big Bang. Only a very small fraction of the emitted fragments are light nuclei, but these states are of fundamental interest. We report the observation of antihypertritons-comprising an antiproton, an antineutron, and an antilambda hyperon-produced by colliding gold nuclei at high energy. Our analysis yields 70 +/- 17 antihypertritons (3/Lambda(H) over bar) and 157 +/- 30 hypertritons ((3)(Lambda)H). The measured yields of (3)(Lambda)H (3/Lambda(H) over bar) and (3)He ((3)(He) over bar) are similar, suggesting an equilibrium in coordinate and momentum space populations of up, down, and strange quarks and antiquarks, unlike the pattern observed at lower collision energies. The production and properties of antinuclei, and of nuclei containing strange quarks, have implications spanning nuclear and particle physics, astrophysics, and cosmology.

The electronic structure of chalcopyrites—bands, point defects and grain boundaries

Abstract: We summarize the progress made recently in understanding the electronic structure of chalcopyrites. New insights into the dispersion of valence and conduction band allow conclusions on the effective masses of charge carriers and their orientation dependence, which influences the transport in solar cell absorbers of different orientation. Native point defects are responsible for the doping and thus the band bending in solar cells. Results of optoelectronic defect spectroscopy are reviewed. Native defects are also the source for a number of metastabilities, which strongly affect the efficiency of solar cells. Recent theoretical findings relate these effects to the Se vacancy and the InCu antisite defect. Experimentally determined activation energies support these models. Absorbers in chalcopyrite solar cells are polycrystalline, which is only possible because of the benign character of the grain boundaries. This can be related to an unusual electronic structure of the GB. Copyright © 2010 John Wiley & Sons, Ltd.

The Unitary Fermi Gas: From Monte Carlo to Density Functionals

Abstract: In this chapter, we describe three related studies of the universal physics of two-component unitary Fermi gases with resonant short-ranged interactions. First we discuss an ab initio auxiliary field quantum Monte Carlo technique for calculating thermodynamic properties of the unitary gas from first principles. We then describe in detail a Density Functional Theory (DFT) fit to these thermodynamic properties: the Superfluid Local Density Approximation (SLDA) and its Asymmetric (ASLDA) generalization. We present several applications, including vortex structure, trapped systems, and a supersolid Larkin-Ovchinnikov (FFLO/LOFF) state. Finally, we discuss the time-dependent extension to the density functional (TDDFT) which can describe quantum dynamics in these systems, including non-adiabatic evolution, superfluid to normal transitions and other modes not accessible in traditional frameworks such as a Landau-Ginzburg, Gross-Pitaevskii, or quantum hydrodynamics.

Highly porous titanium scaffolds for orthopaedic applications

Abstract: For many years, the solid metals and their alloys have been widely used for fabrication of the implants replacing hard human tissues or their functions. To improve fixation of solid implants to the surrounding bone tissues, the materials with porous structures have been introduced. By tissue ingrowing into a porous structure of metallic implant, the bonding between the implant and the bone has been obtained. Substantial pore interconnectivity, in metallic implants, allows extensive body fluid transport through the porous implant. This can provoke bone tissue ingrowth, consequently, leading to the development of highly porous metallic implants, which could be used as scaffolds in bone tissue engineering. The goal of this study was to develop and then investigate properties of highly porous titanium structures received from powder metallurgy process. The properties of porous titanium samples, such as microstructure, porosity, Young's modulus, strength, together with permeability and corrosion resistance were investigated. Porous titanium scaffolds with nonhomogeneous distribution of interconnected pores with pore size in the range up to 600 μm in diameter and a total porosity in the range up to 75% were developed. The relatively high permeability was observed for samples with highest values of porosity. Comparing to cast titanium, the porous titanium was low resistant to corrosion. The mechanical parameters of the investigated samples were similar to those for cancellous bone. The development of high-porous titanium material shows high potential to be modern material for creating a 3D structure for bone regeneration and implant fixation.

First proton--proton collisions at the LHC as observed with the ALICE detector: measurement of the charged particle pseudorapidity density at $\ sqrt(s)$= 900 GeV

Abstract: On 23rd November 2009, during the early commissioning of the CERN Large Hadron Collider (LHC), two counter-rotating proton bunches were circulated for the first time concurrently in the machine, at the LHC injection energy of 450 GeV per beam. Although the proton intensity was very low, with only one pilot bunch per beam, and no systematic attempt was made to optimize the collision optics, all LHC experiments reported a number of collision candidates. In the ALICE experiment, the collision region was centred very well in both the longitudinal and transverse directions and 284 events were recorded in coincidence with the two passing proton bunches. The events were immediately reconstructed and analyzed both online and offline. We have used these events to measure the pseudorapidity density of charged primary particles in the central region. In the range vertical bar eta vertical bar S collider. They also illustrate the excellent functioning and rapid progress of the LHC accelerator, and of both the hardware and software of the ALICE experiment, in this early start-up phase.

Renewable Energy Operation and Conversion Schemes: A Summary of Discussions During the Seminar on Renewable Energy Systems

Abstract: A short summary of some speeches given during Seminar on Renewable Energy system (SERENE) is presented. The contributions have been mainly focused on power electronics for photovoltaic (PV) and sea wave energies, pointing out some aspects related to efficiency, reliability, and grid integration. Finally, main issues concerning fuel cell (FC) systems as generators based on hydrogen as a low environmental impact energy vector are presented.