Showing papers in "Aeronautical Journal in 2010"

Implicit large eddy simulation of ship airwakes

Abstract: Implicit large eddy simulations (ILES) of two different Royal Navy ships have been conducted as part of the UK Ship/Air Interface Frame-work project using a recently developed very high order accuracy numerical method. Time-accurate CFD data for fourteen flow angles was produced to incorporate into flight simulators for definition of safe helicopter operating limits (SHOLs). This paper discusses the flow phenomenology for the different wind directions and where possible reports on the validation of the ILES results for mean and fluctuating velocity components and spectra against experimental data.

The impact of flight simulation in aerospace

Abstract: This paper explains how flight simulation has made a major contri- bution to flight safety over the last thirty years to become critical to the operation of civil airlines and military organisations. It not only provides effective training, but for many flight training organisations has reduced the cost of flight training significantly. The paper outlines the increasing role of flight simulation covering flight training and research and development of aircraft and systems. The contribution of the flight simulation industry to the UK economy, in terms of both employment and revenue, is highlighted. The paper focuses on advances in the underpinning technologies of flight simulation, including mathematical modelling, real-time computation, motion actuation, visual image generation systems and projection systems. The paper also summarises the broadening roles of flight simulation; from part-task trainers to zero flight-time training in civil aviation; in military aviation, extending to combat domes and mission rehearsal; in defence procurement, where synthetic environments are used widely in evaluation studies prior to major project commitments; in aircraft development, providing powerful design tools to enable system designers to evaluate prototype systems. As a result of the acceptance of flight simulation in flight training, the use of simulators has been standardised throughout the world, with formal programmes of simulator qualification. These regulations, drawn up with the help of the RAeS Flight Simulation Group, ensure consistency for operators, regulators and manufacturers; the status of these regulations is outlined. The paper concludes by reviewing the lessons learnt by the flight simulation industry over the last thirty years and summaries the potential areas of growth, which will lead to simulation becoming widespread throughout many industries, in addition to the aerospace industry.

Recent extensions and applications of the ‘CST’ universal parametric geometry representation method

Abstract: For aerodynamic design optimisation as \Veil as for multidisciplinary design optimisation stlldies , it is very desirable to limit the number of the geometric design variables. In Ref I , a ' fundamental' parametric :Jcrofoil geometry represcntation method was presented. The method included the introduction of a geometric 'class function/shape function' transformation technique, CST, s ueh that roLlnd nose/sharp aft end geometries as well as o ther c lasses of geometries could be represented exactly by analytic well behaved and simple mathematical function s having easily observed physical features, The CST method was s hown to dcscrihe a n cssentially limillcss dcsign spacc composed entirel y of analytically smooth geometri es. In Ref. 2, th e CST methodo'iogy was extended to more gene ral three dimensional applications such as wing, body, ducts and nace ll cs. It was shown that any general 3D geometry can be repre­ sented by a distribution of fund amental shapes, and that th e 'shape function/c la ss funct ion ' methodology can be used to describe th e fundame ntal shapes as wcll as thc distributi ons of the fundamental shapes, A number of applications of the 'CST' method to nacelles, ducts, wings and bodies were presented to illustrate th e versatility of this new methodology, In this paper, the CST tllethou is extended to include geometric warping such as variable camber, simple flap, aeroelastic and flutter deflections. The usc of the CST method for geometric morphing of one geometric shape into another is a lso shown. The use of CST analy ti c wings in design optimisation will also be discussed.

Mechanical Behavior of Materials – Second edition W. F. Hosford Cambridge University Press, The Edinburgh Building, Shaftesbury Road, Cambridge, CB2 2RU, UK. 2010. 419pp. £55. ISBN 978-0-521-19569-0.

Abstract: A fairly detailed chapter by chapter review of the first edition (prepared by the current reviewer) appeared in The Aeronautical Journal November 2005 (pages 590-591). Interested parties may care to read this earlier review as a prelude to what is written here. The principal difference between first and second editions may be summarised as follows: The treatment of defects is new, as is the analysis of particulate composites. Slip systems and the effect of textures on crystallographic microstructures, discontinuous/inhomogeneous deformation, also the treatment of foams, are new topics considered in revised or additional chapters. With the exception of Mechanical Testing (Chapter 3) and Mechanical Working (Chapter 22) (both pitched at technician level) the text is highly theoretical and in places quite advanced. Hence the author’s call for readers to have what he calls “a basic knowledge of Materials Science and three-dimensional strength calculations”. A self-evident truth is that there is far more to learn than can be taught in a single course and this leads the author to suggest that “various chapters or portions of chapters may be omitted”. The author skims rapidly through the essentials of three-dimensional Stress, Strain, Elasticity, Mechanical Testing and Strain Hardening (in Chapters 1, 2, 3 and 4) then on to Plasticity Theory (Chapter 5). These sections can clearly be taught as a standalone unit to those not up to ‘speed’. But readers needing to learn fully about materials testing will find Chapter 3 limited in scope to purely mechanical items and issues. Load cells and extensometers are mentioned en passant, but no useful information is given on other electro/magnetic or optical devices. There is, however, much else to read on other topics which is at the highest level. To pick but one example from Plasticity Theory (Chapter 5). The author emphasises the importance of understanding the relationship between flow, effective strain, effective stress (three-dimensional effects) and their use in conjunction with yield criteria. The author’s method is based on the Von Aircraft Propulsion and Gas Turbine Engines

Aerodynamic study of corrugated skins for morphing wing applications

Abstract: Corrugated structures offer a potential solution for morphing wing skin applications due to their anisotropic behaviour that allows chordwise camber and length changes. Aerofoils with corrugated skins in the aft 1/3 of the chordwise section have been studied experimentally and computationally using various corrugation shapes and forms (sinusoidal, trapezoidal and triangular) at different Reynolds numbers. The study showed that the aerodynamic performance is highly dependent on corrugation amplitude, wavelength, gradient (combination of amplitude and wavelength) and Reynolds number. Evidence is given highlighting that penalties for having a non-smooth surface in the aft 1/3 of the chordwise section of an aerofoil can be eliminated for the lift curve slope and minimised for the zero lift drag coefficient.

Non-linear system identification of the dynamics of aeroelastic instability suppression based on targeted energy transfers

Abstract: We revisit our earlier study of targeted energy transfer (TET) mechanisms for aeroelastic instability suppression by employing time-domain nonlinear system identification based on the equivalence between analytical and empirical slow flows. Performing multiscale partitions of the dynamics directly on measured (or simulated) time series without any presumptions regarding the type and strength of the system nonlinearity, we derive nonlinear interaction models (NIMs) as sets of intrinsic modal oscillators (IMOs). The eigenfre-quencies of IMOs are characterised by the ‘fast’ dynamics of the problem and their forcing terms represent slowly-varying nonlinear modal interactions across the different time scales of the dynamics. We demonstrate that NIMs not only provide information on modal energy exchanges under nonlinear resonant interactions, but also directly dictate robustness behaviour of TET mechanisms for suppressing aeroelastic instabilities. Finally, we discuss the usefulness of NIMs in constructing frequency-energy plots that reveal global features of the dynamics to distinguish between different TET mechanisms and to study robustness of aeroelastic instability suppression.

Starting characteristics of a rectangular supersonic air-intake with cowl deflection

Abstract: Experimental and computational investigations have been made to obtain the details of the flow field of a supersonic air-intake with different cowl deflection angles and back pressures at the exit. The flow field obtained with an inviscid computation on the basic configuration, designed for Mach 2·2, shows starting behaviour whereas computation with k-ω turbulence model and experiments indicate unstart characteristics. Both experiments and computations indicate that provision of a small angle at the cowl tip leads to start of the same intake and also improves it’s performance. Results obtained with cowl deflection shows a better performance in comparison to performance achieved with a basic intake and with a bleed of 2·8%. Sustainable back pressure could be obtained through the computations made at different back pressures for different cowl deflection angles. Overall results suggest that provision of small cowl deflection angle itself leads to improvement in performance achieved in comparison to a bleed of 2·8%, even with back pressure at the exit.

Load transportation system based on autonomous small size helicopters

Abstract: This paper is devoted to modelling and control algorithms for a slung load transportation system composed of one or multiple helicopters, where the load is coupled by the means of flexible ropes (see Fig. 1). The coupled helicopter system overcomes the payload limitation of a single small size helicopter, while keeping most of its advantages: small costs of operation, low maintenance costs and increased safeness. Therefore, the system can be utilised whenever the use of full size helicopters is impossible, too expensive or prohibited by law. We focus on the deployment and repairing of distributed sensor networks, using a transportation system based on multiple small size helicopters. A possible real world application is the deployment of fire fighting equipment, where space limitation of the fire trucks prohibits the application of bigger UAVs and using full size helicopters is too dangerous. The problem of load transportation using one or two full size helicopters (twin lift helicopter system), connected to the load by means of flexible ropes, has been discussed in the aerospace research community at least since 1960. We have shown in our previous work that there is a fundamental difference in the mathematical description between small and full size helicopters. Therefore, also the control design for the case of small size helicopters needs to be different. To our knowledge, the control of a slung load transportation system composed of multiple small size helicopters has not been studied until now. In this paper, the complete mechanical setup of the slung load transportation system based on one or more small size helicopters is presented. This includes a short description of the used UAVs, the additionally required sensors, and how the load is mounted. A model of one/multiple helicopters transporting a load is introduced. This model is used in a simplified form for the controller design and in full form for simulation. The controller for one and two helicopters, which is based on a state feedback controller, as well as the controller for three and more helicopters, which is based on a non linear controller, are explained in detail. Both controllers utilise an underlying non-linear orientation controller. We propose a feedback loop, based on forces measured in the ropes, to compensate for the influence of the rope. The controllers were tested in simulation and in real flight experiments. The world wide first flight experiment with three coupled helicopters was successfully conducted at the end of 2007.

A finite element stress analysis of aircraft bolted joints loaded in tension

Abstract: Accurate stress and strain analysis in bolted joints is of considerable interest in order to design more efficient and safer aerospace structural elements. In this paper, a finite element modelling of aluminium alloy 7075-T6 bolted plates, which are extensively used in aircraft structures, is discussed. The ANSYS Finite Element (FE) package was used for modelling the joint and estimating the stresses and strains created in the joint due to initial clamping forces and subsequent longitudinal tensile loadings. A double-lap bolted joint with a single bolt and nut was considered in the study. A three-dimensional (3D) finite element model of the joint was generated, and then subjected to three different simulated clamping forces followed by different levels of longitudinal tensile load. 3D surface-to-surface contact elements were employed to model the contact between the various components of the bolted joint. Friction effects were considered in the numerical analysis; and moreover, the clearance between the bolt and the plates was simulated in the model. FE results revealed beneficial compressive stresses near the hole edge as a result of applying the clamping. It was found that a higher clamping force can significantly decrease the magnitude of the resultant tensile stress at the hole edge and also bearing stress in the joint when subjected to the longitudinal tensile load.

Optimisation of RNAV noise and emission abatement standard instrument departures

Abstract: In an effort to reduce the negative impact of civil aviation on the human environment, trajectory optimisation techniques have been used to minimise the single event impact of noise and gaseous emissions of departures on communities in the vicinity of airports. For this purpose, the earlier developed trajectory optimisation tool NOISHHH has been adapted to design departure trajectories optimised for environmental criteria, based on area navigation. The new version of NOISHHH combines a noise model, an emissions inventory model, a geographic information system and a dynamic trajectory optimisation algorithm to generate flight paths with minimised environmental impact. Operational constraints have been introduced to ensure that the resulting flight paths are fully compliant with the guidelines and regulations that apply to the design of standard instrument departures and the use of area navigation. To illustrate the capabilities of the new version of NOISHHH, two numerical examples are presented, which are both redesigns of standard instrument departures currently in use at Amsterdam Airport Schiphol.

An overview of experiments on the dynamic sensitivity of MAVs to turbulence

Abstract: Aspects of the turbulent wind environment Micro Air Vehicles (MAVs) experience when flying outdoors were replicated in a large wind tunnel. An overview of the facility, instrumentation and initial flight tests is given. Piloting inputs and aircraft accelerations were recorded on fixed and rotary wing MAVs and for some tests, measurements of the approach flow (u,v,w sampled at 1,250Hz at four laterally disposed upstream locations) were made. The piloting aim was to hold straight and level flight in the 12m wide × 4m high × ~50m long test section, while flying in a range of turbulent conditions. The Cooper-Harper rating system showed that a rotary craft was less sensitive to the effects of turbulence compared to the fixed wing craft and that while the fixed wing aircraft was relatively easy to fly in smooth air, it became extremely difficult to fly under high turbulence conditions. The rotary craft, while more difficult to fly per. se., did not become significantly harder to fly in relatively high turbulence levels. However the rotary craft had a higher mass and MOI than the fixed wing craft and further work is planned to understand the effects of these differences.

New adaptive controller method for SMA hysteresis modelling of a morphing wing

Abstract: A neuro-fuzzy controller method for smart material actuator (SMA) hysteresis modelling is presented, conceived for a morphing wing application. The controller correlates each set of forces and electrical currents that are applied to the smart material actuators with the actuator elongation. The actuator is experimentally tested for four forces, using a variable electrical current. The final controller is obtained through the Matlab/Simulink integration of three independent neuro-fuzzy controllers, designed for the increase and decrease of electrical current, and for null electrical current in the cooling phase of the actuator. This final controller gives a very small error with respect to the experimental values.

Mechanics and aerodynamics of perching manoeuvres in a large bird of prey

Abstract: This paper reviews recent results on the mechanics and aerodynamics of perching in a large bird of prey, the Steppe Eagle Aquila nipalensis. Data collected using onboard and high-speed video cameras are used to examine gross morphing of the wing planform by the flight muscles, and smaller-scale morphing of the wing profile by aeroelastic deflection of the feathers, Carruthers et al. High-resolution still images are used to reconstruct the shape of the wing using multi-station photogrammetry, and the performance of the measured wing profile is analysed using a panel code, Carruthers et al. In bringing these lines of research together, we examine the role of aeroelastic feather deflection, and show that the key to perching in birds lies not in high-lift aerodynamics, but in the way in which the wings and tail morph to allow the bird to transition quickly from a steady glide into a deep stall.

Estimates of the climate impact of future small-scale supersonic transport aircraft – results from the HISAC EU-project

Abstract: The climate impacts of three fleets of supersonic small-scale transport aircraft (S4TA) are simulated. Based on characteristic aircraft parameters, which were developed within the EU-project HISAC, emissions along geographically representative trajectories are calculated and in addition the resulting changes in the atmospheric composition (carbon dioxide, ozone layer, water vapour) and climate (near surface global mean temperature) are deduced. We assume a fleet development with an entry in service in 2015, a full fleet in 2050. The results show a temperature increase of 0·08mK (0·07-0·10mK) with only small but statistically significant variations between the configurations, leading to a minimum climate impact for a weight optimised and hence lower flying aircraft. A climate impact ratio of 3·0 ± 0·4 between a S4TA and its subsonic counterpart is calculated, which is considerable less than for previous supersonic fleets because of a lower flight altitude, leading to smaller water vapour impacts.

Goodness dispersion curves for ultrasonic guided wave based SHM: a sample problem in corrosion monitoring

Abstract: Ultrasonic guided wave techniques have great potential for structural health monitoring applications. Appropriate mode and frequency selection is the basis for achieving optimised damage monitoring performance. In this paper, several important guided wave mode attributes are introduced in addition to the commonly used phase velocity and group velocity dispersion curves while using the general corrosion problem as an example. We first derive a simple and generic wave excitability function based on the theory of normal mode expansion and the reciprocity theorem. A sensitivity dispersion curve is formulated based on the group velocity dispersion curve. Both excitability and sensitivity dispersion curves are verified with finite element simulations. Finally, a goodness dispersion curve concept is introduced to evaluate the tradeoffs between multiple mode selection objectives based on the wave velocity, excitability and sensitivity.

Performing co-ordinated turns with articulated wing-tips as multi-axis control effectors

Abstract: This paper investigates a novel method for the control of aircraft. The concept consists of articulated split wing-tips, independently actuated and mounted on a baseline flying wing. The general philosophy behind the concept was that adequate control of a flying wing about its three axes could be obtained through local modifications of the dihedral angle at the wing-tips, thus providing an alternative to conventional control effectors such as elevons and drag rudders. Preliminary computations with a vortex lattice model and subsequent wind tunnel tests and Navier-Stokes computations demonstrate the viability of the concept for co-ordinated turns, with individual and/or combined wing-tip deflections producing multi-axis, coupled control moments. The multi-axis nature of the generated moments tends to over-actuate the flight control system, leading to some redundancy, which could be exploited to optimise secondary objective functions such as drag or bending moment.

Aviation and climate change: confronting the challenge

Abstract: Each year greenhouse gas emissions remain high the climate mitigation and adaptation challenges grow. The economic downturn was already in train in 2008, yet concentrations of CO2 increased unabated. Without concerted effort across all sectors there will be little chance of avoiding ‘dangerous climate change’ and the aviation sector has a clear role to play. Current and forthcoming technologies, operational practices and behavioural change offer widespread opportunities for other sectors to mitigate their CO2 emissions in absolute terms, but as they do so, aviation will become an increasingly important player. By comparing a range of global cross-sector emission scenarios with existing aviation projections, this paper illustrates the importance of understanding the future context with regard to other sectors when assessing the aviation industry’s potential impact. Given growth projections for aviation and the relatively slow pace of technological change, aviation’s proportion of 2050 global CO2 emissions is low only in those global cross-sector emission scenarios where there is a high probability of ‘dangerous climate change’. For a ‘reasonable’ (>50%) chance of avoiding ‘dangerous climate change’, the most technologically radical scenarios for aviation make up 15% of global CO2 in 2050 and conventional scenarios exceed the carbon budget entirely. Only by recognising that aviation’s currently projected emissions are incompatible with avoiding ‘dangerous climate change’ can the industry fully grasp the challenge of accelerating innovation and managing demand to deliver a more sustainable route to 2050 and beyond.

Drag reduction on a spiked body at hypersonic speed

Abstract: Fitting a spike on a blunt body provides a drag reduction at supersonic and hypersonic speeds. In this study, the laminar flow over a spiked, conical body terminated by a spherical cap, inspired by the Apollo re-entry capsule design, was investigated using a hypersonic wind tunnel. Schlieren pictures revealed the absence of flow unsteadiness for the range of spike lengths tested, and force measurements showed a maximum reduction of 77% of the unspiked body drag. A simple theoretical model based on the pressure drag generated by a solid cone showed good agreement with the experimental data. The measured shock stand-off distance agreed well with predictions.

Fire and evacuation analysis in BWB aircraft configurations: computer simulations and large-scale evacuation experiment

Abstract: How long would it take to evacuate a blended wing body (BWB) aircraft with around 1,000 passengers and crew? How long would it take an external post-crash fire to develop non-survivable conditions within the cabin of a BWB aircraft? Is it possible for all the passengers to safely evacuate from a BWB cabin subjected to a post-crash fire? These questions are explored in this paper through computer simulation. As part of project NACRE, the airEXODUS evacuation model was used to explore evacuation issues associated with BWB aircraft and to investigate fire issues, the CFD fire simulation software SMARTFIRE was used. The fire and evacuation simulations were then coupled to investigate how the evacuation would proceed under the conditions produced by a post-crash fire. In conjunction with this work, a large-scale evacuation experiment was conducted in February 2008 to verify evacuation model predictions. This paper presents some of the results produced from this analysis.

An evaluation of the historical issues associated with achieving non-helicopter V/STOL capability and the search for the flying car

Abstract: Copyright @ 2010 The Royal Aeronautical Society. This article is the final author version of the published paper.

Blended wing body structural concept development

Abstract: A lightweight robust airframe design is one of the key technological advancements necessary for the successful launch of a blended wing body aircraft. The non-circular pressure cabin dictates that substantial improvements beyond current state-of-the-art aluminium and composite structures is needed, and that improvements of this magnitude will require radically new airframe design and manufacturing practices. Such an approach is described in this paper. It is a highly integrated structural concept that is tailored and optimised to fully exploit the orthotropic nature and unique processing advantages inherent in dry carbon fibres, while also employing stitching to enable a unique damage-arrest design approach.

Development and validation of an efficient direct numerical optimisation approach for aerofoil shape design

Abstract: Intelligent shape optimisation architecture is developed, validated and applied in the design of high-altitude long endurance aerofoil (HALE). The direct numeric optimisation (DNO) approach integrating a geometrical shape parameterisation model coupled to a validated flow solver and a population based search algorithm are applied in the design process. The merit of the DNO methodology is measured by computational time efficiency and feasibility of the optimal solution. Gradient based optimisers are not suitable for multimodal solution topologies. Thus, a novel particle swarm optimiser with adaptive mutation (AM-PSO) is developed. The effect of applying the PARSEC and a modified variant of the original function, as a shape parameterisation model on the global optimal is verified. Optimisation efficiency is addressed by mapping the solution topology for HALE aerofoil designs and by computing the sensitivity of aerofoil shape variables on the objective function. Variables with minimal influence are identified and eliminated from shape optimisation simulations. Variable elimination has a negligible effect on the aerodynamics of the global optima, with a significant reduction in design iterations to convergence. A novel data-mining technique is further applied to verify the accuracy of the AM-PSO solutions. The post-processing analysis, to swarm optimisation solutions, indicates a hybrid optimisation methodology with the integration of global and local gradient based search methods, yields a true optima. The findings are consistent for single and multi-point designs.

Aerodynamics: A Discipline Swept Away?

Abstract: This contribution is based on the Lanchester Lecture of the Royal Aeronautical Society held in Manchester, UK, in October 2009. The lecture reflected on further possible perspectives for aeronautical research, in particular with respect to aerodynamics. The air transport system of today has matured to very high performance and safety standards. However, due to the ongoing global developments of economy and ecology, new challenges have to be faced. Thus, the relevance of all engineering aeronautical disciplines contributing to the final aircraft configuration is now closely scrutinised, and especially aerodynamics is challenged whether any investment in further research is still justified. In this contribution, it is argued that, when carefully exploited, aerodynamics still offers a substantial technological perspective, well beyond the concepts for the next generation of aircraft as currently being pursued. As an example, the aerodynamics of a forward swept-wing are discussed and it is outlined that, when combining the transonic characteristics of a forward swept-wing with the advantages of natural laminar-flow, considerable improvements in efficiency may be gained. However, this potential may only be leveraged through a strategic, long-term orientation of fundamental and applied research.

Numerical simulation of the flow field over conical, disc and flat spiked body at Mach 6

Abstract: A forward facing spike attached to a hemispherical body significantly changes its flow field and influences aerodynamic drag and wall heat flux in a high speed flow. The dynamic pressure in the recirculation area is highly reduced and this leads to the decrease in the aerodynamic drag and heat load on the surface. Consequently, the geometry, that is, the length and shape of the spike, has to be simulated in order to obtain a large conical recirculation region in front of the blunt body to get beneficial drag reduction. It is, therefore, a potential candidate for aerodynamic drag reduction for a future high speed vehicle. Axisymmetric compressible laminar Navier-Stokes equations are solved using a finite volume discretisation in conjunction with a multistage Runge-Kutta time stepping scheme. The effect of the spike length and shape, and the spike nose configuration on the reduction of drag is numerically evaluated at Mach 6 at a zero angle-of-attack. The computed density contours agree well with the schlieren images. Additional modification to the tip of the spike to get different types of flow field such as the formation of a shock wave, separation area and reattachment point are examined. The spike geometries include the conical spike, the flat-disk spike and the hemispherical disk spike of different length to diameter ratios attached to the blunt body.

Design and realisation of a two-seater aircraft powered by fuel cell electric propulsion

Abstract: The main objective of the project is to develop and validate the use of a fuel cell based power system for the propulsion of more/all electric aircraft. The Rapid 200-FC two-seater electric-motor-driven aeroplane which is powered by fuel cells is at present being completed and will be validated during a flight test in Autumn 2009. Several configurations have been evaluated in order to install the new energy and propulsion system on board while maintaining the centre of gravity within allowable limits. The fuel cell system and the electric motor are being integrated on board. The FC stack will be able to deliver a maximum continuous power of 20kW. A battery pack has to guarantee another 20kW of maximum continuous power for a limited time period (15 minutes), during take-off, climbing and, in the case of emergency, during landing. The main goal of the project is to validate the overall high performance of an all electric aircraft system which is capable of remaining aloft for one hour. A parametric analysis has also been carried out to evaluate which key technologies influence the performance of future aircraft to the greatest extent.

Computational and experimental study of intake ground vortices

Abstract: The ground vortices generated by an intake under both headwind and crosswind configurations have been investigated using computational and experimental approaches. The flow field of a scale-model intake was experimentally studied using stereoscopic particle image velocimetry to measure the ground vortex in conjunction with induct total pressure measurements for the internal flow. The computational predictions were performed using an unsteady Reynolds averaged Navier-Stokes approach. The experimental results show that under crosswind conditions a single ground vortex forms which becomes stronger as the crossflow velocity is increased. Under headwind conditions the measured ground vortex strength initially increases with freestream velocity before it reaches a local maximum and then reduces thereafter. The computations also exhibit the same characteristics and show good agreement with the measurements for some configurations. Based on the predictions, the complex flow field topology is investigated and a detailed flow model of the vortex flow field under crosswind conditions is proposed.

Supersonic Aerodynamics of a Projectile with Slot Cavities

Abstract: This paper presents the results of experimental and computational investigations on the effect of slot cavities on a supersonic projectile. Experimental work was carried out to show the effects of the slots on the drag at Mach numbers M =1.36, 1.65, 1.83. The computational analysis was done at M = 1.36. A single configuration of the slot pattern was used with two different slot widths (0.5mm and 2.0mm). Flow features were investigated in the slotted area and at the base. The analysis presented includes the pressure distribution, the supersonic cavity flow and the effect of the slots on the overall aerodynamic drag. Unlike the case of slots at transonic speeds, the suction and blowing mechanism is not found at supersonic Mach numbers. Streamwise cavity slots cause a small base drag reduction. The reduction in total drag is modest when the width is 0.5mm. However, the experiments showed that with the wider slots (2mm) the drag actually increases at Mach numbers from 1.36 to 1.83.

Simulation of automatic helicopter deck landings using nature inspired flight control

Abstract: Research studies have indicated that the optical flow parameter, time to close tau, is the basis of purposeful control in the animal world, and used by both fixed wing and helicopter pilots during manoeuvring. This parameter is defined as the instantaneous time to close a gap (spatial or force) at the current closing rate. A novel automatic flight control strategy has been developed that makes use of optical flow theory and in particular, the parameter tau. This strategy has been applied to two distinct problems; (1) the landing of a helicopter on a ship and (2) the lateral repositioning of a helicopter. The first is a challenging case because the landing of a helicopter on a ship is one of the most dangerous of all helicopter flight operations. Furthermore, helicopters are often subject to torque oscillations during rapid collective control, which increases pilot workload significantly when operating with low power margins and/or whilst performing tasks that require accurate heave control. The second case demonstrates the generality of the technique. Both automatic manoeuvres were simulated successfully within desired limits, with the novel control strategy creating a ‘natural’, smooth, tau motion.

New methodology and code for Hawker 800XP aircraft stability derivatives calculation from geometrical data

Abstract: The new FDerivatives code was conceived and developed for calculating static and dynamic stability derivatives of an aircraft in the subsonic regime, based on its geometrical data. The code is robust and it uses geometries and flight conditions to calculate the aircraft’s stability derivatives. FDerivatives contains new algorithms and methods that have been added to DATCOM’s classical method, presented in a USAF Stability and Control DATCOM reference. The new code was written using MATLAB and has a complex structure which contains a graphical interface to facilitate the work of potential users. Results obtained with the new code were evaluated and validated with flight test data provided by CAE Inc. for the Hawker 800XP business aircraft.

6U CubeSat design for Earth observation with 6.5m GSD, five spectral bands and 14Mbps downlink

Abstract: The design of a 6U CubeSat including spacecraft systems and imaging payload is described for an Earth observation mission. From a Sun synchronous orbit at an altitude of 600km the design enables imaging with a 6.5m GSD, an optical MTF (on axis) of >59% at half Nyquist and >35% at Nyquist, a 26km swath, 12 bit digitisation and SNR of 120-200:one in five spectral bands; blue, green, red, red edge and near infrared. Data can be downlinked at the rate of 14 Mbps to a 3.7m S band ground station. This design allows an 8kg CubeSat to perform Earth observation missions equivalent to those of current 50-150kg microsatellites, with a corresponding reduction in cost.