Showing papers in "Organic Electronics in 2017"

TL;DR: In this article, pectin, a byproduct has not been recycled sustainably, is introduced as an insulator to fabricate a novel organic resistive switching memory devices with Ag/Pectin/FTO structure for the first time.

TL;DR: In this paper, the in-situ thermal-annealing doctor blading was developed to fabricate high-quality perovskite CH3NH3PbI3 thin film and efficient planar heterojunction perovsite solar cells (PHJ-PSCs) in ambient condition with humidity of ∼45%.

TL;DR: In this paper, a roll-to-roll (R2R) micro-gravure printing process was developed to deposit the electron transport layer (ETL) using low-temperature, solution-processable zinc oxide (ZnO) nanoparticle ink on flexible substrate for fabricating inverted organic solar cells (OSCs).

TL;DR: In this article, the performance of organic photovoltaics (OPV) and conventional amorphous silicon solar cells (a-Si) for indoor light harvesting was investigated.

TL;DR: In this article, the remarkable crystalline structures of P3ATs comprising single crystals, nanofibers, nano/microwires, nanoribbons, micelles, nanowhiskers, thin films, spherulites, etc.

TL;DR: A high strain sensor composed of elastomer polydimethylsiloxane (PDMS) and polyaniline (PANI) was fabricated by electrodeposition method for PANI preparation and daubing method for PDMS preparation as discussed by the authors.

TL;DR: In this article, the hole transport material (HTM) is used to improve the hole mobility of inverted perovskite solar cells by adding graphene oxide (GO) to the PEDOT:PSS HTM.

TL;DR: In this paper, a polyethylene terephthalate (PET) film substrate was used to fabricate organic light-emitting diodes (OLEDs) without an additional surface planarization.

TL;DR: In this paper, a large area and high performance perovskite CH3NH3PbI3 photodetectors fabricated via in-situ thermal-treatment doctor blading technique in ambient condition (humidity ∼45%).

TL;DR: In this paper, the authors used the time-dependent density functional theory to study the property of excited states of TADF emitters, and it was found that both the geometry and the electronic structure are quite dependent on the functionals.

TL;DR: In this paper, the effect of different ratios of OMMT and MWCNT nanofillers and potential synergistic effect of these fillers on the crystalline structure of PVDF and the performance of resulting piezo-device were studied.

TL;DR: In this article, the fabrication of organic poly(3-hexylthiophene) (P3HT) synaptic transistors gated by the ionic liquid/poly(vinylidene fluoride-co-trifluoroethylene) [P(VDF-TrFE)] hybrid electrolyte was reported.

TL;DR: In this paper, a universal model for the transient drain current response in organic electrochemical transistors (OECTs) is presented, which is applicable to both plain and membrane-functionalized devices.

TL;DR: In this article, an intermediate CNT concentration of 6.7 Wt% showed the highest thermopower and power factor, and the origin of unusual transport properties was suggested by studying changes in the relative ratio of conducting PEDOT core and insulating PSS, morphology, and carrier concentration and mobility.

TL;DR: In this paper, an inkjet-printed Ag grid combined with Ag nanowires was used to form a transparent hybrid electrode for flexible organic light emitting diode (F-OLED).

TL;DR: In this article, the optical and electronic properties of PBTTT-C14 thin-films prepared by the static and the dynamic casting on liquid substrate were investigated considering the advantages of floating film transfer method (FTM).

TL;DR: In this article, the effects of edge types and edge defects on the electronic and transport properties of phosphorene nanoribbons (PNRs) were investigated by performing first-principle quantum transport calculations.

TL;DR: In this article, a high smooth, conductive, and uniform flexible transparent composite film is produced by embedding silver nanowires (AgNWs) into polymer without high-temperature annealing.

TL;DR: In this article, the electrical and ammonia gas sensing properties of a poly (3, 3, 3, dialkylquaterthiophene) (PQT-12) based organic thin film transistor (OTFT) fabricated by floating-film transfer method (FTM) on a highly doped p-type silicon substrate has been presented possibly for the first time in this paper.

TL;DR: Using TiO2 nanoparticles as binders, highly conductive carbon films were prepared and used to fabricate monolithic hole-conductor-free perovskite solar cell in air.

TL;DR: In this paper, a highly conductive, smooth and transparent electrode is developed by coating poly (3,4-ethylenedioxythiophene):poly (styrenesulfonate) (PEDOT:PSS) over silver nanowires (AgNWs) followed by a hot-pressing method.

TL;DR: Wang et al. as discussed by the authors showed that using Wox/C60 as EELs offer a simple and effective approach for fabricating high performance and low-temperature perovskite solar cells.

TL;DR: In this paper, three star-shaped S/Se-annulated perylene diimide (PDI) small molecule acceptors with triphenylamine as the core were designed and synthesized.

TL;DR: In this paper, high sensitive near-infrared (NIR) organic phototransistors (OPTs) were fabricated using nanowire network based on a narrow bandgap donor-acceptor (D-A) polymer as the photoactive channel.

TL;DR: In this article, a hybrid thin-film encapsulation stack consisting of two inorganic barrier layers of silicon nitride with an organic layer in between was applied to protect OLEDs from local cathode oxidation.

TL;DR: In this paper, the authors reviewed the recent advance of benzimidazole-based iridium (III) complexes with focus on the design strategies, photophysical properties and EL performances of phosphorescent OLEDs with various benzimide derivatives including substituents, functionalized ancillary ligand and dendrimers.

TL;DR: In this paper, a composite of poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT:PSS) and single-wall carbon nanotube (SWCNT) was prepared by mixing aqueous dispersions of PEDOT and SWCNT at different weight ratios.

TL;DR: In this paper, a 2-(thiophen-2-yl)quinoline-based phosphorescent iridium(III) complexes bearing 2-(3-(trifluoromethyl)-1H-1,2,4-triazol-5-yl)-pyridine or picolinic acid as ancillary ligands are designed and synthetised.

TL;DR: In this article, two ladder-type small molecule acceptors IDT-BT-R and IDTBT-CN are utilized in non-fullerene polymer solar cells by pairing with PTB7-Th as donor polymer, in which the solar cells achieve high performance up to 8.3% with high voltage of 1.02

TL;DR: In this article, the NiO nanocrystals (NCs) are fabricated by a simple solvothermal method using tert-butyl alcohol and nickel acetylacetonate as precursors at 200°C for different reaction times.