Journal ArticleDOI
Interfacial reaction behavior and bonding mechanism between liquid Sn and ZrO2 ceramic exposed in ultrasonic waves
TLDR
In this article, an ultrasonic-assisted dipping of ZrO2 ceramics into molten Sn solder was performed to realize the low-temperature joining of ZRO2 poramics in this study, and the results showed that after ultrasonically dipping in molten Sn for 1200 seconds, a pure Sn solder layer with a thickness of approximately 8-9 µm was coated on the Zr O2 surface.About:
This article is published in Ceramics International.The article was published on 2017-07-01. It has received 15 citations till now. The article focuses on the topics: Ceramic & Microstructure.read more
Citations
More filters
Journal ArticleDOI
Ultrasonic soldering of Cu alloy using Ni-foam/Sn composite interlayer.
TL;DR: Results showed that exceptional metallurgic bonding could be acquired with the assistance of ultrasonic vibration using a self-developed Ni-foam/Sn composite solder.
Journal ArticleDOI
Low-temperature ultrasound-activated joining of ZrO2 ceramics using Sn–Al–Cu solder
Dong Hongjie,Z.L. Li,Xiaoguo Song,Guo Xiajun,Luo Yanxu,Tiansheng Bai,Shoujing Wei,Hongyun Zhao,Jiuchun Yan,Jicai Feng +9 more
Journal ArticleDOI
Fabrication and abrasive wear behavior of ZrO2-SiC-Al2O3 ceramic
Shanmu Xu,Youguo Xu,Yangai Liu,Minghao Fang,Xiaowen Wu,Xin Min,Xiaoguang Zhang,Zhaohui Huang +7 more
TL;DR: In this paper, ZrO 2 -SiC-Al 2 O 3 ceramic was fabricated by as-prepared zircon as raw material and carbon black as reductant.
Journal ArticleDOI
Ultrasound-assisted soldering of alumina using Ni-foam reinforced Sn-based composite solders
TL;DR: In this article, the effects of ultrasonic soldering time on the microstructure and mechanical properties of joints were investigated, and a pure Sn metallization layer which exhibited excellent metallurgic bonding with Al 2 O 3 ceramic was fabricated by ultrasonic dipping for more than 40 hours.
Journal ArticleDOI
Ultrasonic aqueous synthesis of corrosion resistant hydroxyapatite coating on magnesium alloys for the application of long-term implant.
TL;DR: In the immersion test of 90 days, HA coatings could provide a long-term protection for magnesium alloy substrate, indicating that ultrasonic aqueous synthesized HA coating could be acted as a promising modified biomaterial on magnesium alloys for the orthopedic application.
References
More filters
Journal ArticleDOI
Ultrasonic Cavitation at Solid Surfaces
TL;DR: This review is intended to summarize recent progress and to point out most promising directions of ultrasound application for the development of new materials with functional surfaces.
Journal ArticleDOI
Low-temperature degradation of different zirconia ceramics for dental applications.
Philipp Kohorst,Lothar Borchers,J. Strempel,Meike Stiesch,Thomas Hassel,Friedrich-Wilhelm Bach,Christoph Hübsch +6 more
TL;DR: Results indicate that both alumina and ceria, as stabilizing oxides, reduce the susceptibility of zirconia to hydrothermal degradation; the alternative use of these oxides may enhance the clinical long-term stability of dental zIRconia restorations.
Journal ArticleDOI
Joining of engineering ceramics
TL;DR: In this article, the basic difference in atomic bonding between the ionic or covalent bonding of the ceramic, compared to the metallic bond is considered, as well as the mismatch in the coefficient of thermal expansion.
Journal ArticleDOI
Controlled Hydrothermal Synthesis of Zirconium Oxide Nanostructures and Their Optical Properties
TL;DR: In this paper, X-ray diffraction examination demonstrates that the as-synthesized zirconia is of pure monoclinic phase (m-ZrO2).
Journal ArticleDOI
Microstructural evolution and characterisation of interfacial phases in Al2O3/Ag-Cu-Ti/Al2O3 braze joints
TL;DR: In this article, active braze alloy (ABA) Ag-35.3Cu-1.8Ti-wt.% and brazing cycles that peak at temperatures between 815°C and 875°C for 2 to 300 min.