Avram Bar-Cohen

Bio: Avram Bar-Cohen is an academic researcher from University of Maryland, College Park. The author has contributed to research in topic(s): Heat transfer & Heat sink. The author has an hindex of 50, co-authored 329 publication(s) receiving 8329 citation(s). Previous affiliations of Avram Bar-Cohen include Auburn University & DARPA.

Thermally optimum spacing of vertical, natural convection cooled, parallel plates

Abstract: While component dissipation patterns and system operating modes vary widely, many electronic packaging configurations can be modeled by symmetrically or asymmetrically isothermal or isoflux plates. The idealized configurations are amenable to analytic optimization based on maximizing total heat transfer per unit volume or unit primary area. To achieve this anlaytic optimization, however, it is necessary to develop composite relations for the variation of the heat transfer coefficient along the plate surfaces. The mathematical development and verification of such composite relations as well as the formulation and solution of the optimizing equations for the various boundary conditions of interest constitute the core of this presentation.

Thermally Optimum Spacing of Vertical, Natural Convection Cooled, Parallel Plates

Abstract: While component dissipation patterns and system operating modes vary widely, many electronic packaging configurations can be modeled by symmetrically or asymmetrically isothermal or isoflux plates. The idealized configurations are amenable to analytic optimization based on maximizing total heat transfer per unit volume or unit primary area. To achieve this anlaytic optimization, however, it is necessary to develop composite relations for the variation of the heat transfer coefficient along the plate surfaces. The mathematical development and verification of such composite relations as well as the formulation and solution of the optimizing equations for the various boundary conditions of interest constitute the core of this presentation.

Thermal Analysis and Control of Electronic Equipment

Abstract: Thermal analysis and control of electronic equipment , Thermal analysis and control of electronic equipment , مرکز فناوری اطلاعات و اطلاع رسانی کشاورزی

Direct Liquid Cooling of High Flux Micro and Nano Electronic Components

Abstract: The inexorable rise in chip power dissipation and emergence of on-chip hot spots with heat fluxes approaching 1 =kW/cm2 has turned renewed attention to direct cooling with dielectric liquids. Use of dielectric liquids in intimate contact with the heat dissipating surfaces eliminates the deleterious effects of solid-solid interface resistances and harnesses the highly efficient phase-change processes to the critical thermal management of advanced IC chips. In the interest of defining the state-of-the-art in direct liquid cooling, this paper begins with a discussion of the thermophysics of phase-change processes and a description of the available dielectric liquid cooling techniques and their history. It then describes the phenomenology of pool boiling, spray/jet impingement, gas-assisted evaporation, and synthetic jet impingement with dielectric liquids. Available correlations for predicting the heat transfer coefficients and limiting heat transfer rates, as well as documented empirical results for these promising techniques for on-chip hot spot cooling, are also provided and compared

Advances in Thermal Modeling of Electronic Components and Systems. Volume 1

Abstract: This volume opens with a sweeping overview of the physical design of electronic systems-methodology, technology, and future challenges-thermally induced failures in electronic systems. Subsequent chapters examine the causes for thermally induced failures of electronic components and the techniques used to analyze and prevent such failures. It gives a comprehensive bibliograhy of project managers and lead engineers, packaging engineers and mechanical analysts, consultants, and academic, industrial, and government laboratory researchers.

Review on thermal energy storage with phase change: materials, heat transfer analysis and applications

Abstract: Thermal energy storage in general, and phase change materials (PCMs) in particular, have been a main topic in research for the last 20 years, but although the information is quantitatively enormous, it is also spread widely in the literature, and difficult to find. In this work, a review has been carried out of the history of thermal energy storage with solid–liquid phase change. Three aspects have been the focus of this review: materials, heat transfer and applications. The paper contains listed over 150 materials used in research as PCMs, and about 45 commercially available PCMs. The paper lists over 230 references.

Light-emitting diodes

Abstract: Light-Emitting Diodes. (Monographs in Electrical and Electronic Engineering.) By A. A. Bergh and P. J. Dean. Pp. viii+591. (Clarendon: Oxford; Oxford University: London, 1976.) £22.

The MEMS Handbook

Abstract: Part I: Background and Fundamentals Introduction, Mohamed Gad-el-Hak, University of Notre Dame Scaling of Micromechanical Devices, William Trimmer, Standard MEMS, Inc., and Robert H. Stroud, Aerospace Corporation Mechanical Properties of MEMS Materials, William N. Sharpe, Jr., Johns Hopkins University Flow Physics, Mohamed Gad-el-Hak, University of Notre Dame Integrated Simulation for MEMS: Coupling Flow-Structure-Thermal-Electrical Domains, Robert M. Kirby and George Em Karniadakis, Brown University, and Oleg Mikulchenko and Kartikeya Mayaram, Oregon State University Liquid Flows in Microchannels, Kendra V. Sharp and Ronald J. Adrian, University of Illinois at Urbana-Champaign, Juan G. Santiago and Joshua I. Molho, Stanford University Burnett Simulations of Flows in Microdevices, Ramesh K. Agarwal and Keon-Young Yun, Wichita State University Molecular-Based Microfluidic Simulation Models, Ali Beskok, Texas A&M University Lubrication in MEMS, Kenneth S. Breuer, Brown University Physics of Thin Liquid Films, Alexander Oron, Technion, Israel Bubble/Drop Transport in Microchannels, Hsueh-Chia Chang, University of Notre Dame Fundamentals of Control Theory, Bill Goodwine, University of Notre Dame Model-Based Flow Control for Distributed Architectures, Thomas R. Bewley, University of California, San Diego Soft Computing in Control, Mihir Sen and Bill Goodwine, University of Notre Dame Part II: Design and Fabrication Materials for Microelectromechanical Systems Christian A. Zorman and Mehran Mehregany, Case Western Reserve University MEMS Fabrication, Marc J. Madou, Nanogen, Inc. LIGA and Other Replication Techniques, Marc J. Madou, Nanogen, Inc. X-Ray-Based Fabrication, Todd Christenson, Sandia National Laboratories Electrochemical Fabrication (EFAB), Adam L. Cohen, MEMGen Corporation Fabrication and Characterization of Single-Crystal Silicon Carbide MEMS, Robert S. Okojie, NASA Glenn Research Center Deep Reactive Ion Etching for Bulk Micromachining of Silicon Carbide, Glenn M. Beheim, NASA Glenn Research Center Microfabricated Chemical Sensors for Aerospace Applications, Gary W. Hunter, NASA Glenn Research Center, Chung-Chiun Liu, Case Western Reserve University, and Darby B. Makel, Makel Engineering, Inc. Packaging of Harsh-Environment MEMS Devices, Liang-Yu Chen and Jih-Fen Lei, NASA Glenn Research Center Part III: Applications of MEMS Inertial Sensors, Paul L. Bergstrom, Michigan Technological University, and Gary G. Li, OMM, Inc. Micromachined Pressure Sensors, Jae-Sung Park, Chester Wilson, and Yogesh B. Gianchandani, University of Wisconsin-Madison Sensors and Actuators for Turbulent Flows. Lennart Loefdahl, Chalmers University of Technology, and Mohamed Gad-el-Hak, University of Notre Dame Surface-Micromachined Mechanisms, Andrew D. Oliver and David W. Plummer, Sandia National Laboratories Microrobotics Thorbjoern Ebefors and Goeran Stemme, Royal Institute of Technology, Sweden Microscale Vacuum Pumps, E. Phillip Muntz, University of Southern California, and Stephen E. Vargo, SiWave, Inc. Microdroplet Generators. Fan-Gang Tseng, National Tsing Hua University, Taiwan Micro Heat Pipes and Micro Heat Spreaders, G. P. "Bud" Peterson, Rensselaer Polytechnic Institute Microchannel Heat Sinks, Yitshak Zohar, Hong Kong University of Science and Technology Flow Control, Mohamed Gad-el-Hak, University of Notre Dame) Part IV: The Future Reactive Control for Skin-Friction Reduction, Haecheon Choi, Seoul National University Towards MEMS Autonomous Control of Free-Shear Flows, Ahmed Naguib, Michigan State University Fabrication Technologies for Nanoelectromechanical Systems, Gary H. Bernstein, Holly V. Goodson, and Gregory L. Snider, University of Notre Dame Index

A review of Ga2O3 materials, processing, and devices

Abstract: Gallium oxide (Ga2O3) is emerging as a viable candidate for certain classes of power electronics, solar blind UV photodetectors, solar cells, and sensors with capabilities beyond existing technologies due to its large bandgap. It is usually reported that there are five different polymorphs of Ga2O3, namely, the monoclinic (β-Ga2O3), rhombohedral (α), defective spinel (γ), cubic (δ), or orthorhombic (e) structures. Of these, the β-polymorph is the stable form under normal conditions and has been the most widely studied and utilized. Since melt growth techniques can be used to grow bulk crystals of β-GaO3, the cost of producing larger area, uniform substrates is potentially lower compared to the vapor growth techniques used to manufacture bulk crystals of GaN and SiC. The performance of technologically important high voltage rectifiers and enhancement-mode Metal-Oxide Field Effect Transistors benefit from the larger critical electric field of β-Ga2O3 relative to either SiC or GaN. However, the absence of clear demonstrations of p-type doping in Ga2O3, which may be a fundamental issue resulting from the band structure, makes it very difficult to simultaneously achieve low turn-on voltages and ultra-high breakdown. The purpose of this review is to summarize recent advances in the growth, processing, and device performance of the most widely studied polymorph, β-Ga2O3. The role of defects and impurities on the transport and optical properties of bulk, epitaxial, and nanostructures material, the difficulty in p-type doping, and the development of processing techniques like etching, contact formation, dielectrics for gate formation, and passivation are discussed. Areas where continued development is needed to fully exploit the properties of Ga2O3 are identified.