Review on thermal energy storage with phase change: materials, heat transfer analysis and applications

Light-Emitting Diodes. (Monographs in Electrical and Electronic Engineering.) By A. A. Bergh and P. J. Dean. Pp. viii+591. (Clarendon: Oxford; Oxford University: London, 1976.) £22.

/pdf/light-emitting-diodes-ubzde6g9qc.pdf

Light-emitting diodes

Gallium oxide (Ga2O3) is emerging as a viable candidate for certain classes of power electronics, solar blind UV photodetectors, solar cells, and sensors with capabilities beyond existing technologies due to its large bandgap. It is usually reported that there are five different polymorphs of Ga2O3, namely, the monoclinic (β-Ga2O3), rhombohedral (α), defective spinel (γ), cubic (δ), or orthorhombic (e) structures. Of these, the β-polymorph is the stable form under normal conditions and has been the most widely studied and utilized. Since melt growth techniques can be used to grow bulk crystals of β-GaO3, the cost of producing larger area, uniform substrates is potentially lower compared to the vapor growth techniques used to manufacture bulk crystals of GaN and SiC. The performance of technologically important high voltage rectifiers and enhancement-mode Metal-Oxide Field Effect Transistors benefit from the larger critical electric field of β-Ga2O3 relative to either SiC or GaN. However, the absence of clear demonstrations of p-type doping in Ga2O3, which may be a fundamental issue resulting from the band structure, makes it very difficult to simultaneously achieve low turn-on voltages and ultra-high breakdown. The purpose of this review is to summarize recent advances in the growth, processing, and device performance of the most widely studied polymorph, β-Ga2O3. The role of defects and impurities on the transport and optical properties of bulk, epitaxial, and nanostructures material, the difficulty in p-type doping, and the development of processing techniques like etching, contact formation, dielectrics for gate formation, and passivation are discussed. Areas where continued development is needed to fully exploit the properties of Ga2O3 are identified.

A review of Ga2O3 materials, processing, and devices

International Technology Roadmap for Semiconductors 2003の要求清浄度について － シリコンウエハ表面と雰囲気環境に要求される清浄度, 分析方法の現状について －

Small, light weight and multifunctional electronic components are attracting much attention because of the rapid growth of the wireless communication systems and microwave products in the consumer electronic market. The component manufacturers are thus forced to search for new advanced integration, packaging and interconnection technologies. One solution is the low temperature cofired ceramic (LTCC) technology enabling fabrication of three-dimensional ceramic modules with low dielectric loss and embedded silver electrodes. During the past 15 years, a large number of new dielectric LTCCs for high frequency applications have been developed. About 1000 papers were published and ∼500 patents were filed in the area of LTCC and related technologies. However, the data of these several very useful materials are scattered. The main purpose of this review is to bring the data and science of these materials together, which will be of immense help to researchers and technologists all over the world. The comme...

Low loss dielectric materials for LTCC applications: a review

Linear Transformations. Elements of the Linear Transformations. Singular Fins and Spines and Single Elements. Algorithms for Finned Array Assembly. Examples of Finned Array Analysis. Reciprocity and Node Analysis. A General Array Method. Convective Optimizations. Heat Transfer-Parallel Plate Heat Sinks. References. Appendices. Indexes.

Design and analysis of heat sinks

In present-day high-performance electronic components, the generated heat loads result in unacceptably high junction temperatures and reduced component lifetimes. Thermoelectric modules can, in principle, enhance heat removal and reduce the temperatures of such electronic devices. However, state-of-the-art bulk thermoelectric modules have a maximum cooling flux qmax of only about 10 W cm−2, while state-of-the art commercial thin-film modules have a qmax <100 W cm−2. Such flux values are insufficient for thermal management of modern high-power devices. Here we show that cooling fluxes of 258 W cm−2 can be achieved in thin-film Bi2Te3-based superlattice thermoelectric modules. These devices utilize a p-type Sb2Te3/Bi2Te3 superlattice and n-type δ-doped Bi2Te3−xSex, both of which are grown heteroepitaxially using metalorganic chemical vapour deposition. We anticipate that the demonstration of these high-cooling-flux modules will have far-reaching impacts in diverse applications, such as advanced computer processors, radio-frequency power devices, quantum cascade lasers and DNA micro-arrays. Current thermoelectric modules provide cooling fluxes that are insufficient for high-heat flux applications. Here, the authors demonstrate thin-film-based thermoelectric modules capable of providing cooling fluxes more than double that of the current state-of-the-art.

/pdf/superlattice-based-thin-film-thermoelectric-modules-with-f5vl9gdag2.pdf

Superlattice-based thin-film thermoelectric modules with high cooling fluxes

Thermal management of electronic components with dielectric liquids

Design of Optimum Plate-Fin Natural Convective Heat Sinks

The rapid emergence of nanoelectronics, with the consequent rise in transistor density and switching speed, has led to a steep increase in microprocessor chip heat flux and growing concern over the emergence of on-chip “hot spots”. The application of on-chip high heat flux cooling techniques is today a primary driver for innovation in the electronics industry. In this paper, the physical phenomena underpinning the most promising on-chip thermal management approaches for hot spot remediation, along with basic modeling equations and typical results are described. Attention is devoted to thermoelectric microcoolers — using mini-contcat enhancement and in-plane thermoelectric currents, orthotropic TIM’s/heat spreaders, and phase-change microgap coolers.Copyright © 2009 by ASME

Avram Bar-Cohen

Papers

Design and analysis of heat sinks

Superlattice-based thin-film thermoelectric modules with high cooling fluxes

Thermal management of electronic components with dielectric liquids

Design of Optimum Plate-Fin Natural Convective Heat Sinks

Thermal Management of On-Chip Hot Spot