Showing papers in "Review of Scientific Instruments in 2004"

Analysis of heat flow in layered structures for time-domain thermoreflectance

Abstract: The iterative algorithm of Feldman for heat flow in layered structures is solved in cylindrical coordinates for surface heating and temperature measurement by Gaussian-shaped laser beams. This solution for the frequency-domain temperature response is then used to model the lock-in amplifier signals acquired in time-domain thermoreflectance measurements of thermal properties.

Cantilever transducers as a platform for chemical and biological sensors

Abstract: Since the late 1980s there have been spectacular developments in micromechanical or microelectro-mechanical (MEMS) systems which have enabled the exploration of transduction modes that involve mechanical energy and are based primarily on mechanical phenomena. As a result an innovative family of chemical and biological sensors has emerged. In this article, we discuss sensors with transducers in a form of cantilevers. While MEMS represents a diverse family of designs, devices with simple cantilever configurations are especially attractive as transducers for chemical and biological sensors. The review deals with four important aspects of cantilever transducers: (i) operation principles and models; (ii) microfabrication; (iii) figures of merit; and (iv) applications of cantilever sensors. We also provide a brief analysis of historical predecessors of the modern cantilever sensors.

Power spectrum analysis for optical tweezers

Abstract: The force exerted by an optical trap on a dielectric bead in a fluid is often found by fitting a Lorentzian to the power spectrum of Brownian motion of the bead in the trap. We present explicit functions of the experimental power spectrum that give the values of the parameters fitted, including error bars and correlations, for the best such χ2 fit in a given frequency range. We use these functions to determine the information content of various parts of the power spectrum, and find, at odds with lore, much information at relatively high frequencies. Applying the method to real data, we obtain perfect fits and calibrate tweezers with less than 1% error when the trapping force is not too strong. Relatively strong traps have power spectra that cannot be fitted properly with any Lorentzian, we find. This underscores the need for better understanding of the power spectrum than the Lorentzian provides. This is achieved using old and new theory for Brownian motion in an incompressible fluid, and new results for ...

Instrumentation for trace detection of high explosives

Abstract: There is at present an urgent need for trace detection of high explosives, with applications to screening of people, packages, luggage, and vehicles. A great concern, because of recent terrorist activities, is for the development of methods that might allow detection and identification of explosives at a stand off distance. Nearly every analytical chemical method has been or is being applied to this problem. This review outlines the properties of explosives that might be utilized in detection schemes, discusses sampling issues, presents recent method developments with particular attention to detection limits, speed of analysis, and portability, and looks towards future developments.

Two-dimensional charged particle image inversion using a polar basis function expansion

Abstract: We present an inversion method called pBasex aimed at reconstructing the original Newton sphere of expanding charged particles from its two-dimensional projection by fitting a set of basis functions with a known inverse Abel integral. The basis functions have been adapted to the polar symmetry of the photoionization process to optimize the energy and angular resolution while minimizing the CPU time and the response to the cartesian noise that could be given by the detection system. The method presented here only applies to systems with a unique axis of symmetry although it can be adapted to overcome this restriction. It has been tested on both simulated and experimental noisy images and compared to the Fourier-Hankel algorithm and the original Cartesian basis set used by [Dribinski et al.Rev. Sci. Instrum. 73, 2634 (2002)], and appears to give a better performance where odd Legendre polynomials are involved, while in the images where only even terms are present the method has been shown to be faster and simpler without compromising its accuracy.

Normal and torsional spring constants of atomic force microscope cantilevers

Abstract: Two methods commonly used to measure the normal spring constants of atomic force microscope cantilevers are the added mass method of Cleveland et al. [J. P. Cleveland et al., Rev. Sci. Instrum. 64, 403 (1993)], and the unloaded resonance technique of Sader et al. [J. E. Sader, J. W. M. Chon, and P. Mulvaney, Rev. Sci. Instrum. 70, 3967 (1999)]. The added mass method involves measuring the change in resonant frequency of the fundamental mode of vibration upon the addition of known masses to the free end of the cantilever. In contrast, the unloaded resonance technique requires measurement of the unloaded resonant frequency and quality factor of the fundamental mode of vibration, as well as knowledge of the plan view dimensions of the cantilever and properties of the fluid. In many applications, such as frictional force microscopy, the torsional spring constant is often required. Consequently, in this article, we extend both of these techniques to allow simultaneous calibration of both the normal and torsional spring constants. We also investigate the validity and applicability of the unloaded resonance method when a mass is attached to the free end of the cantilever due to its importance in practice.

Preparation of gold tips suitable for tip-enhanced Raman spectroscopy and light emission by electrochemical etching

Abstract: We describe a method of preparing gold scanning tunneling microscopy (STM) tips by direct current electrochemical etching in concentrated HCl and ethanol solution. Gold tips with tip apex radius lower than 30 nm can be reproducibly prepared by this method. The influence of the solution composition, etching voltage on the surface structure, and sharpness has been investigated. These tips can be efficiently used for STM imaging, tip-enhanced Raman spectroscopy, and light emission investigations on the same sample.

Line-imaging velocimeter for shock diagnostics at the OMEGA laser facility

Abstract: A line-imaging velocity interferometer has been implemented at the OMEGA laser facility of the Laboratory for Laser Energetics, University of Rochester. This instrument is the primary diagnostic for a variety of experiments involving laser-driven shock-wave propagation, including high-pressure equation of state experiments, materials characterization experiments, shock characterization for Rayleigh–Taylor experiments, and shock timing experiments for inertial confinement fusion research. Using a laser probe beam to illuminate a target, the instrument measures shock breakout times at temporal resolutions as low as 20 ps, and spatial resolution ∼4 μm. For velocity measurements the detection limit is <0.1 km/s, and velocities of interfaces, free surfaces, and shock fronts traveling through transparent media can be measured with accuracies ∼1% over the range from 4 km/s to greater than 50 km/s. Quantitative measurements of the optical reflectance of ionizing shock fronts can also be obtained simultaneously with the velocity measurements.

Femtosecond broadband stimulated Raman spectroscopy: Apparatus and methods.

Abstract: The laser, detection system, and methods that enable femtosecond broadband stimulated Raman spectroscopy (FSRS) are presented in detail. FSRS is a unique tool for obtaining high time resolution (<100 fs) vibrational spectra with an instrument response limited frequency resolution of <10 cm(-1). A titanium:Sapphire-based laser system produces the three different pulses needed for FSRS: (1) A femtosecond visible actinic pump that initiates the photochemistry, (2) a narrow bandwidth picosecond Raman pump that provides the energy reservoir for amplification of the probe, and (3) a femtosecond continuum probe that is amplified at Raman resonances shifted from the Raman pump. The dependence of the stimulated Raman signal on experimental parameters is explored, demonstrating the expected exponential increase in Raman intensity with concentration, pathlength, and Raman pump power. Raman spectra collected under different electronic resonance conditions using highly fluorescent samples highlight the fluorescence rejection capabilities of FSRS. Data are also presented illustrating our ability: (i) To obtain spectra when there is a large transient absorption change by using a shifted excitation difference technique and (ii) to obtain high time resolution vibrational spectra of transient electronic states.

The plasma mirror—A subpicosecond optical switch for ultrahigh power lasers

Abstract: Plasma mirrors are devices capable of switching very high laser powers on subpicosecond time scales with a dynamic range of 20–30 dB. A detailed study of their performance in the near-field of the laser beam is presented, a setup relevant to improving the pulse contrast of modern ultrahigh power lasers (TW–PW). The conditions under which high reflectivity can be achieved and focusability of the reflected beam retained are identified. At higher intensities a region of high specular reflectivity with rapidly decreasing focusability was observed, suggesting that specular reflectivity alone is not an adequate guide to the ideal range of plasma mirror operation. It was found that to achieve high reflectivity with negligible phasefront distortion of the reflected beam the inequality csΔt<λLaser must be met (cs: sound speed, Δt: time from plasma formation to the peak of the pulse). The achievable contrast enhancement is given by the ratio of plasma mirror reflectivity to cold reflectivity.

Dante soft x-ray power diagnostic for National Ignition Facility

Abstract: Soft x-ray power diagnostics are essential for measuring the total x-ray flux, radiation temperature, conversion efficiency, and albedo that define the energetics in indirect and direct drive, as well as other types of high temperature laser plasma experiments. A key diagnostic for absolute radiation flux and radiation temperature in hohlraum experiments is the Dante broadband soft x-ray spectrometer. For the extended range of x-ray fluxes predicted for National Ignition Facility (NIF) compared to Omega or Nova hohlraums, the Dante spectrometer for NIF will include more high energy (<2 keV) edge filter band-pass channels and access to an increased dynamic range using grids and signal division. This will allow measurements of radiation fluxes of between 0.01 to 100 TW/sr, for hohlraum radiation temperatures between 50 eV and 1 keV. The NIF Dante will include a central four-channel imaging line-of-sight to verify the source size, alignment as well as checking for any radiation contributions from unconverted...

Performance of uncooled microcantilever thermal detectors

Abstract: It has recently been shown that bimaterial microcantilevers can be used as uncooled infrared detectors. Bimaterial microcantilevers deform as their temperature changes due to the absorption of infrared photons. Infrared imaging using uncooled cantilever arrays has already been achieved by a number of groups. In this paper, we examined the performance of microcantilevers as uncooled infrared detectors with optical readout. As in the case of other kinds of uncooled thermal infrared detectors, temperature fluctuation noise and background fluctuation noise are fundamental limits to the performance of microcantilever thermal detectors. Since microcantilevers are mechanical devices, thermo-mechanical noise will also influence their performance. We fabricated a SiNx microcantilever thermal detector with an Al layer in the bimaterial region. For the microcantilever geometry and materials used, the background fluctuation noise equivalent temperature difference, NETDBF, calculated for f/1 optics and a 30 Hz frame rate was found to be 1.26 mK. The NETDTF, limited by temperature fluctuation noise, was calculated to be 7.4 mK while the thermo-mechanical NETDTM was calculated to be 5.3 mK. The sum of all fundamental noise sources, including the intrinsic noise of the “optical lever” readout, results in a total NETD of 9.2 mK. Absence of the readout noise would improve this parameter by only 2%.

Miniature spectroscopic instrumentation: Applications to biology and chemistry

Abstract: Spectroscopy is a fundamental analytical tool utilized throughout all of the sciences. For chemistry and biology alone, there are thousands of applications. In the past two decades there have been monumental advances in the miniaturization of components used in spectrophotometric systems. The key components include detector arrays, laser diodes, and fiber optics. Currently, there are numerous commercially available miniature spectrometer systems as well as discrete components that are used by researchers in designing their own systems. A comprehensive summary of current instrumentation available for the design and development of miniaturized spectroscopy applications is described, including detectors, wavelength discriminating components, light sources, and sampling assemblies. Recommendations are made for designing spectrometer systems for specific applications. Current literature is reviewed for chemical and biological applications specifically using miniaturized spectrometer systems with the focus being on ultraviolet-visible-near-infrared spectrometers. The applications include laboratory applications, environmental sensing, on-site industrial analyses, botany and ecology applications, and finally clinical and biochemical studies. Additionally, microspectrometers, two-dimensional arrays, and photonics crystals are discussed in regards to their future role in chemistry and biology applications.

Viscoelastic measurement techniques

Abstract: Methods for measuring viscoelastic properties of solids are reviewed The nature of viscoelastic response is first presented This is followed by a survey of time and frequency-domain considerations as they apply to mechanical measurements Subresonant, resonant, and wave methods are discussed, with applications

Ultrahigh vacuum glancing angle deposition system for thin films with controlled three-dimensional nanoscale structure

Abstract: An ultrahigh vacuum apparatus for the deposition of thin films with controlled three-dimensional nanometer-scale structure is described. Our system allows an alternate, faster, cheaper way of obtaining nanoscale structured thin films when compared to traditional procedures of patterning and etching. It also allows creation of porous structures that are unattainable with known techniques. The unique feature of this system is the dynamic modification of the substrate tilt and azimuthal orientation with respect to the vapor source during deposition of a thin film. Atomic-scale geometrical shadowing creates a strong directional dependence in the aggregation of the film, conferring control over the resulting morphological structure on a scale of less than 10 nm. Motion can create pillars, helixes, zig–zags, etc. Significant features of the apparatus include variable substrate temperature, insertion and removal of specimens from atmospheric conditions without venting the deposition system, computer controlled p...

High resolution Thomson scattering for Joint European Torus (JET)

Abstract: A Thomson scattering system is being developed for Joint European Torus with 15 mm spatial resolution and a foreseen accuracy for temperature better than 15% at a density of 1019 m−3. This resolution is required at the internal transport barrier and edge pedestal and it can not be fully achieved with the present light detection and ranging systems. The laser for this system is Nd:YAG, 5 Joule, 20 Hz. Scattering volumes from R=2.9 m to R=3.9 m are imaged onto 1 mm diameter fibers, with F/25 collection aperture. Two fibers are used per scattering volume. Using optical delay lines, three scattering volumes are combined in each of the 21 filter polychromators. The signals are recorded with transient digitizers, which allow the combined time delayed signals to be resolved. Knowledge of the time delay between signals allows the use of correlation techniques in determining signal levels. The ac output of the amplifier is used, which tolerates a higher level of background signal without affecting dynamic range. T...

Proton radiography as an electromagnetic field and density perturbation diagnostic (invited)

Abstract: Laser driven proton beams have been used to diagnose transient fields and density perturbations in laser produced plasmas. Grid deflectometry techniques have been applied to proton radiography to obtain precise measurements of proton beam angles caused by electromagnetic fields in laser produced plasmas. Application of proton radiography to laser driven implosions has demonstrated that density conditions in compressed media can be diagnosed with million electron volt protons. This data has shown that proton radiography can provide unique insight into transient electromagnetic fields in super critical density plasmas and provide a density perturbation diagnostics in compressed matter.

Metrological large range scanning probe microscope

Abstract: We describe a metrological large range scanning probe microscope (LR-SPM) with an Abbe error free design and direct interferometric position measurement capability, aimed at versatile traceable topographic measurements that require nanometer accuracy. A dual-stage positioning system was designed to achieve both a large measurement range and a high measurement speed. This dual-stage system consists of a commercially available stage, referred to as nanomeasuring machine (NMM), with a motion range of 25 mm×25 mm×5 mm along x, y, and z axes, and a compact z-axis piezoelectric positioning stage (compact z stage) with an extension range of 2 μm. The metrological LR-SPM described here senses the surface using a stationary fixed scanning force microscope (SFM) head working in contact mode. During operation, lateral scanning of the sample is performed solely by the NMM. Whereas the z motion, controlled by the SFM signal, is carried out by a combination of the NMM and the compact z stage. In this case the compact z...

Europium beta-diketonate temperature sensors: Effects of ligands, matrix, and concentration

Abstract: Europium beta diketonates are easily synthesized highly luminescent complexes with high temperature sensitivity. We report on the temperature dependence of the luminescence of recently synthesized europium complexes originally prepared for use as light emitting diodes. It has been discovered that when incorporated in a polymer matrix, their decay lifetime can provide accurate measurement of temperature. Their lifetime as a function of temperature depends on three factors: (i) the type and number of ligands in the complex, (ii) the particular polymer used for the matrix, and (iii) the europium chelate to polymer matrix concentration ratio. Various tris and tetrakis europium chelates are used to study ligand effects, while the polymers FIB, polycarbonate, and Teflon© are used to analyze matrix effects. In all cases studied, higher concentrations give rise to shorter lifetimes and higher temperature sensitivities, with sensitivity defined as ΔI/(IrefΔT). We propose to explain this phenomenon by using the following equation: 1/τobs≡Ktotal=kr+knr(T)+kc([Eu]). Here Ktotal is the observed decay rate, which is the inverse of the observed lifetime, while kr and knr(T) are the radiative and nonradiative decay rates, respectively. As well as being dependent on temperature, knr(T) for these complexes is very dependent on the environment, i.e., solvent or polymer, and can be considered as ken(T). The rate kc([Eu]) is the quenching term dependent on the concentration of the europium complex.

Frequency-stabilized single-mode cavity ring-down apparatus for high-resolution absorption spectroscopy

Abstract: We present a cavity ring-down spectroscopy apparatus suitable for high-resolution absorption spectroscopy. The central feature of the spectrometer is a ring-down cavity whose comb of eigenfrequencies is actively stabilized with respect to a tuneable, frequency-stabilized reference laser. By using dichroic ring-down cavity mirrors that are designed to have relatively high losses and low losses at the respective wavelengths of the reference laser and probe laser, the cavity stabilization dynamics are decoupled from frequency jitter of the probe laser. We use the cavity eigenfrequencies as markers in spectral scans and achieve a frequency resolution of ≈1 MHz. Five rovibrational transitions in the (2,0,1) vibrational band of water vapor near 0.935 μm are probed with a continuous-wave external-cavity diode laser, and their line strengths are determined and compared to literature values. Collisional narrowing effects and pressure shifting are observed, illustrating the applicability of the method for quantitative line shape studies of weakly absorbing systems.

Trapping and tracking a local probe with a photonic force microscope

Abstract: An improved type of scanning probe microscope system able to measure soft interactions between an optically trapped probe and local environment is presented. Such a system that traps and tracks thermally fluctuating probes to measure local interactions is called a photonic force microscope (PFM). The instrument can be used to study two-dimensional and three-dimensional surface forces, molecular binding forces, entropic and viscoelastic forces of single molecules, and small variations in particle flow, local diffusion, and viscosities. We introduce and characterize a PFM, and demonstrate its outstanding stability and very low noise. The probe’s position can be measured within a precision of 0.2–0.5 nm in three dimensions at a 1 MHz sampling rate. The trapping system facilitates stable trapping of latex spheres with diameter D=λ0/2 at laser powers as low as 0.6 mW in the focal plane. The ratio between the trapping stiffness and laser power was able to be optimized for various trapping conditions. The measur...

Optical communication components

Abstract: We review and contrast key technologies developed to address the optical components market for communication applications. We first review the component requirements from a network perspective. We then look at different material systems, compare their properties, and describe the functions achieved to date in each of them. The material systems reviewed include silica fiber, silica on silicon, silicon on insulator, silicon oxynitride, sol-gels, polymers, thin-film dielectrics, lithium niobate, indium phosphide, gallium arsenide, magneto-optic materials, and birefringent crystals. We then describe the most commonly used classes of optical device technology and present their pros and cons as well as the functions achieved to date in each of them. The technologies reviewed include passive, actuation, and active technologies. The passive technologies described include fused fibers, dispersion-compensating fiber, beam steering, Bragg gratings, diffraction gratings, holographic elements, thin-film filters, photo...

Time-domain laser-induced fluorescence spectroscopy apparatus for clinical diagnostics

Abstract: We report the design and development of a compact optical fiber-based apparatus for in situ time-resolved laser-induced fluorescence spectroscopy (tr-LIFS) of biological systems. The apparatus is modular, optically robust, and compatible with the clinical environment. It incorporates a dual output imaging spectrograph, a gated multichannel plate photomultiplier (MCP-PMT), an intensified charge-coupled-device (ICCD) camera, and a fast digitizer. It can accommodate various types of light sources and optical fiber probes for selective excitation and remote light delivery/collection as required by different applications. The apparatus allows direct recording of the entire fluorescence decay with high sensitivity (nM range fluorescein dye concentration with signal-to-noise ratio of 46) and with four decades dynamic range. It is capable of resolving a broad range of fluorescence lifetimes from hundreds of picoseconds (as low as 300 ps) using the MCP-PMT coupled to the digitizer to milliseconds using the ICCD. T...

Optical tweezers and confocal microscopy for simultaneous three-dimensional manipulation and imaging in concentrated colloidal dispersions

Abstract: A setup is described for simultaneous three-dimensional manipulation and imaging inside a concentrated colloidal dispersion using (time-shared) optical tweezers and confocal microscopy. The use of two microscope objectives, one above and one below the sample, enables imaging to be completely decoupled from trapping. The instrument can be used in different trapping (inverted, upright, and counterpropagating) and imaging modes. Optical tweezers arrays, dynamically changeable and capable of trapping several hundreds of micrometer-sized particles, were created using acousto-optic deflectors. Several schemes are demonstrated to trap three-dimensional colloidal structures with optical tweezers. One combined a Pockels cell and polarizing beam splitters to create two trapping planes at different depths in the sample, in which the optical traps could be manipulated independently. Optical tweezers were used to manipulate collections of particles inside concentrated colloidal dispersions, allowing control over collo...

The LEAF picosecond pulse radiolysis facility at Brookhaven National Laboratory

Abstract: The BNL Laser-Electron Accelerator Facility (LEAF) uses a laser-pulsed photocathode, radio-frequency electron gun to generate ⩾7 ps pulses of 8.7 MeV electrons for pulse radiolysis experiments. The compact and operationally simple accelerator system includes synchronized laser pulses that can be used to probe or excite the electron-pulsed samples to examine the dynamics and reactivity of chemical species on the picosecond time scale.

Measuring methods of cell performance of dye-sensitized solar cells

Abstract: Cell performance measuring methods for dye-sensitized solar cells (DSCs) were investigated in comparison with those of crystalline silicon solar cells. It was found that cell performances of DSCs varied according to voltage sweep direction and sampling delay time. On the other hand, this dependence was not observed in silicon solar cells. Measurement of the transient photocurrent revealed that the dependence on sweep direction and sampling delay time may be explained by the longer time constant of DSCs. To improve accuracy, measurement should be carried out with a sampling delay time exceeding several seconds. However, it is also found that the average value of the efficiency measured by two sweeping directions is constant when the sampling delay time is longer than 40 ms. These measurement conditions will be useful to measuring cell performance more accurately and rapidly. Additionally, determining cell area using a shading mask with an area smaller than that of TiO2 electrodes will improve accuracy when...

Investigation of volatile liquid surfaces by synchrotron x-ray spectroscopy of liquid microjets

Abstract: Soft x-ray absorption spectroscopy is a powerful probe of surface electronic and geometric structure in metals, semiconductors, and thin films. Because these techniques generally require ultrahigh vacuum, corresponding studies of volatile liquid surfaces have hitherto been precluded. We describe the design and implementation of an x-ray experiment based on the use of liquid microjets, permitting the study of volatile liquid surfaces under quasi-equilibrium conditions by synchrotron-based spectroscopy. The liquid microjet temperatures are also characterized by Raman spectroscopy, which connects our structural studies with those conducted on liquid samples under equilibrium conditions. In recent experiments, we have observed and quantified the intermolecular surface relaxation of liquid water and methanol and have identified a large population of “acceptor-only” molecules at the liquid water interface.

Magnetic resonance-guided near-infrared tomography of the breast

Abstract: The design and implementation of a multispectral, frequency-domain near infrared tomography system is outlined, which operates in a MRI magnet for utilization of MR-guided image reconstruction of tissue optical properties. Using long silica optical fiber bundles, measurements of light transmission through up to 12 cm of female breast tissue can be acquired simultaneously with MRI scans. The NIR system utilizes six optical wavelengths from 660 to 850 nm using intensity modulated diode lasers nominally working at 100 MHz. Photomultiplier tube detector gain levels are electronically controlled on a time scale of 200 ms, thereby allowing rapid switching of the source to locations around the tissue. There are no moving parts in the detection channels and for each source position, 15 PMTs operating in parallel allow sensitivity down to 0.5 pW/cm2 at the tissue surface. Images of breast tissue optical absorption and reduced scattering coefficients are obtained using a Newton-type reconstruction algorithm to solv...

Impedance measurements and modeling of a transition-edge-sensor calorimeter

Abstract: We describe a method for measuring the complex impedance of transition-edge-sensor (TES) calorimeters. Using this technique, we measured the impedance of a Mo/Au superconducting transition-edge-sensor calorimeter. The impedance data are in good agreement with our linear calorimeter model. From these measurements, we obtained measurements of unprecedented accuracy of the heat capacity and the gradient of resistance with respect to temperature and current of a TES calorimeter throughout the phase transition. The measurements probe the internal state of the superconductor in the phase transition and are useful for characterizing the calorimeter.

Ultrasensitive, fast, thin-film differential scanning calorimeter

Abstract: The equipment for an ultrasensitive, fast, thin-film differential scanning calorimetry [(TDSC) or nanocalorimetry] technique is described. The calorimetric cell (∼0.30 cm2) operates by applying a short (∼10 ms) dc current pulse (∼10 mA) to a thin (∼50 nm) patterned metal strip, which is supported by a thin (∼50 nm) SiNx membrane. The calorimeter operates at high heating rates (15–200 K/ms) and is very sensitive (30 pJ/K). The design of the calorimeter, the timing/synchronization methods, as well as the choice of key components of the instrument are discussed. Comparisons are made between two dc pulsing circuits that generate the current, a battery powered system and a system based on discharge of an assembly of charged capacitors (recommended). Design concepts for the differential as well as a simplified nondifferential technique are discussed and evaluated via experiments on thin films of indium. The differential design shows an increase in sensitivity, making it suitable for small samples. The custom made electronic circuits are also described, including the design of a preamplifier with low (28×) and high (700×) gain options, which are also compared using experimental data. Noise considerations are critical for the method. Simple models which describe noise levels in the calorimetric data are given and methods for reducing noise are discussed in detail. The sources of noise in the instrument are discussed in terms of both fundamental factors such as Johnson noise of the metal strip, as well as the limiting attributes of the sensing and pulsing circuits and instrumentation. These limiting attributes include spurious signals generated by desorption of ambient gases from the sensor, ground loops, switching regulators, and missing codes in analog-to-digital converter instruments. Examples of the experimental data of heat capacity Cp(T) of various thin films of indium, tin, and polystyrene are presented. A complete data set of raw experimental values is included for a 20 nm sample of Sn which shows the values of current and voltage of both the sample and reference sensors, as well as the differential voltage and the final values of the heat capacity.