Showing papers on "Absorption (electromagnetic radiation) published in 2009"

Atomic layer graphene as saturable absorber for ultrafast pulsed lasers

Abstract: The optical conductance of monolayer graphene is defined solely by the fine structure constant. The absorbance has been predicted to be independent of frequency. In principle, the interband optical absorption in zero-gap graphene could be saturated readily under strong excitation due to Pauli blocking. Here, we demonstrate the use of atomic layer graphene as saturable absorber in a mode-locked fiber laser for the generation of ultrashort soliton pulses (756 fs) at the telecommunication band. The modulation depth can be tuned in a wide range from 66.5% to 6.2% by varying the thickness of graphene. Our results suggest that ultrathin graphene films are potentially useful as optical elements in fiber lasers. Graphene as a laser mode locker can have many merits such as lower saturation intensity, ultrafast recovery time, tunable modulation depth and wideband tuneability.

Two-photon absorption and the design of two-photon dyes.

Abstract: Two-photon absorption has important advantages over conventional one-photon absorption, which has led to applications in microscopy, microfabrication, three-dimensional data storage, optical power limiting, up-converted lasing, photodynamic therapy, and for the localized release of bio-active species. These applications have generated a demand for new dyes with high two-photon absorption cross-sections. This Review introduces the theory of two-photon absorption, surveys the wide range of potential applications, and highlights emerging structure-property correlations that can serve as guidelines for the development of efficient two-photon dyes.

Molecular Understanding of Organic Solar Cells: The Challenges

Abstract: Our objective in this Account is 3-fold. First, we provide an overview of the optical and electronic processes that take place in a solid-state organic solar cell, which we define as a cell in which the semiconducting materials between the electrodes are organic, be them polymers, oligomers, or small molecules; this discussion is also meant to set the conceptual framework in which many of the contributions to this Special Issue on Photovoltaics can be viewed. We successively turn our attention to (i) optical absorption and exciton formation, (ii) exciton migration to the donor−acceptor interface, (iii) exciton dissociation into charge carriers, resulting in the appearance of holes in the donor and electrons in the acceptor, (iv) charge-carrier mobility, and (v) charge collection at the electrodes. For each of these processes, we also describe the theoretical challenges that need to be overcome to gain a comprehensive understanding at the molecular level. Finally, we highlight recent theoretical advances, ...

Optical absorption enhancement in amorphous silicon nanowire and nanocone arrays.

Abstract: Hydrogenated amorphous Si (a-Si:H) is an important solar cell material. Here we demonstrate the fabrication of a-Si:H nanowires (NWs) and nanocones (NCs), using an easily scalable and IC-compatible process. We also investigate the optical properties of these nanostructures. These a-Si:H nanostructures display greatly enhanced absorption over a large range of wavelengths and angles of incidence, due to suppressed reflection. The enhancement effect is particularly strong for a-Si:H NC arrays, which provide nearly perfect impedance matching between a-Si:H and air through a gradual reduction of the effective refractive index. More than 90% of light is absorbed at angles of incidence up to 60° for a-Si:H NC arrays, which is significantly better than NW arrays (70%) and thin films (45%). In addition, the absorption of NC arrays is 88% at the band gap edge of a-Si:H, which is much higher than NW arrays (70%) and thin films (53%). Our experimental data agree very well with simulation. The a-Si:H nanocones functio...

Cavity ring-down spectroscopy: Experimental schemes and applications

Abstract: Cavity ring-down (CRD) spectroscopy is a direct absorption technique, which can be performed with pulsed or continuous light sources and has a significantly higher sensitivity than obtainable in conventional absorption spectroscopy. The CRD technique is based upon the measurement of the rate of absorption rather than the magnitude of absorption of a light pulse confined in a closed optical cavity with a high Q factor. The advantage over normal absorption spectroscopy results from, firstly, the intrinsic insensitivity to light source intensity fluctuations and, secondly, the extremely long effective path lengths (many kilometres) that can be realized in stable optical cavities. In the last decade, it has been shown that the CRD technique is especially powerful in gas-phase spectroscopy for measurements of either strong absorptions of species present in trace amounts or weak absorptions of abundant species. In this review, we emphasize the various experimental schemes of CRD spectroscopy, and we show how th...

Design of Plasmonic Thin‐Film Solar Cells with Broadband Absorption Enhancements

Abstract: Basic design rules are developed for the use of metallic nanostructures to realize broadband absorption enhancements in thin-film solar cells. They are applied to a relevant and physically intuitive model system consisting of a two-dimensional, periodic array of Ag strips on a silica-coated Si film supported by a silica substrate. We illustrate how one can simultaneously take advantage of 1) the high near-fields surrounding the nanostructures close to their surface plasmon resonance frequency and 2) the effective coupling to waveguide modes supported by the thin Si film through an optimization of the array properties. Following this approach, we can attain a 43% enhancement in the short circuit current as compared to a cell without metallic structures. It is suggested that 3-dimensional nanoparticle arrays with even larger boosts in short circuit current can also be generated using the presented framework. Photovoltaic (PV) cells can provide virtually unlimited amounts of energy by effectively converting sunlight into clean electrical power. Silicon has been the material of choice for PV cells due to low cost, earth abundance, non-toxicity, and the availability of a very mature processing technology. The cost of current PV modules still needs to be significantly reduced and efficiency substantially increased to enable large scale implementation. Thin-film, second-generation Si solar cells may provide a viable pathway towards this goal because of their low materials and processing costs. Unfortunately the materials quality and resulting energy conversion efficiencies of such cells are still substantially lower than crystalline, wafer-based cells. This is a direct result of the large mismatch between electronic and photonic length scales in these devices; the absorption depth of light in Si is significantly longer than the electronic (minority carrier) diffusion length in deposited thin-film materials for photon energies close to the band-gap. As a result, charge extraction from optically thick cells is challenging due to carrier recombination in the bulk of the semiconductor. If light absorption could be improved in ultra-thin layers of active material it would lead directly to lower recombination currents, higher open circuit voltages, and higher conversion efficiencies. Conventional, planar anti-reflection (AR) coatings do not provide high transmission efficiencies over the entire solar spectrum and do not enable effective light trapping to increase absorption. Light trapping schemes using diffusely scattering surface textures were first suggested in the 1980s and are by now fairly-well understood. Texturing surfaces of thin film cells is not ideal as it leads to enhanced surface recombination. For this reason, some interesting alternative trapping configurations have been proposed that utilize structuring at length-scales orders of magnitude larger than the cell thickness. More than a decade ago, it was first proposed to use the unique optical properties of metallic (i.e., plasmonic) structures to boost the efficiency of PV cells; those metallic nanostructures exhibit easily accessible collective electron oscillations known as surface plasmons. Surface plasmon excitations enable unparalleled light concentration and trapping. Since these pioneering efforts, plasmonics has also been used to enable new photodetector designs that exploit lateral and in-depth light concentration to increase their signal-to-noise ratio and speed in the visible, near-IR, and mid-IR wavelength ranges. Recently, the use of metallic nanostructures for PV has received renewed attention with the availability of new nanofabrication tools and the growing understanding of their optical properties provided by the burgeoning field of plasmonics. In different cell designs both near-field light concentration close to the individual particle resonance and effective light trapping by nanometallics have been explored. Experimentally, high peak enhancements in the tens of percent range at specific wavelengths and overall efficiency enhancements of 40%, 8.3%, and 8% have been achieved with the use of plasmonic structures for cells employing organics, a-Si, and GaAs, respectively. Separate efforts have focused on increasing the more omni-directional absorption characteristics for solar tracking and operation in diffuse sunlight. These results are very promising, although no detailed comparisons have yet been made to cells employing alternative light trapping technologies. Moreover, there is a clear need for effective optimization strategies that lead to broadband absorption enhancements over the entire solar spectrum. This type of optimization for nanostructured solar cells is now within the realm of possibilities; the recent advances in full-field electromagnetic simulations and computer hardware have resulted in the development of extremely accurate and robust optimization tools that are now commonly used by the PV community. In this paper, we illustrate a straightforward and physically intuitive procedure to optimize the net overall absorption of a thin-film Si solar cell over the entire solar spectrum; this simultaneously takes advantage of 1) the high near-fields surrounding the nanostructures close to their surface plasmon C O M M U N IC A TI O N www.advmat.de

Aerosol light absorption and its measurement: A review

Abstract: Light absorption by aerosols contributes to solar radiative forcing through absorption of solar radiation and heating of the absorbing aerosol layer. Besides the direct radiative effect, the heating can evaporate clouds and change the atmospheric dynamics. Aerosol light absorption in the atmosphere is dominated by black carbon (BC) with additional, significant contributions from the still poorly understood brown carbon and from mineral dust. Sources of these absorbing aerosols include biomass burning and other combustion processes and dust entrainment. For particles much smaller than the wavelength of incident light, absorption is proportional to the particle volume and mass. Absorption can be calculated with Mie theory for spherical particles and with more complicated numerical methods for other particle shapes. The quantitative measurement of aerosol light absorption is still a challenge. Simple, commonly used filter measurements are prone to measurement artifacts due to particle concentration and modification of particle and filter morphology upon particle deposition, optical interaction of deposited particles and filter medium, and poor angular integration of light scattered by deposited particles. In situ methods measure particle absorption with the particles in their natural suspended state and therefore are not prone to effects related to particle deposition and concentration on filters. Photoacoustic and refractive index-based measurements rely on the heating of particles during light absorption, which, for power-modulated light sources, causes an acoustic signal and modulation of the refractive index in the air surrounding the particles that can be quantified with a microphone and an interferometer, respectively. These methods may suffer from some interference due to light-induced particle evaporation. Laser-induced incandescence also monitors particle heating upon absorption, but heats absorbing particles to much higher temperatures to quantify BC mass from the thermal radiation emitted by the heated particles. Extinction-minus-scattering techniques have limited sensitivity for measuring aerosol light absorption unless the very long absorption paths of cavity ring-down techniques are used. Systematic errors can be dominated by truncation errors in the scattering measurement for large particles or by subtraction errors for high single scattering albedo particles. Remote sensing techniques are essential for global monitoring of aerosol light absorption. While local column-integrated measurements of aerosol light absorption with sun and sky radiometers are routinely done, global satellite measurements are so far largely limited to determining a semi-quantitative UV absorption index.

Predicted Efficiency of a Low-Temperature Nanofluid-Based Direct Absorption Solar Collector

Abstract: Due to its renewable and nonpolluting nature, solar energy is often used in applications such as electricity generation, thermal heating, and chemical processing. The most cost-effective solar heaters are of the "flat-plate" type, but these suffer from relatively low efficiency and outlet temperatures. The present study theoretically investigates the feasibility of using a nonconcentrating direct absorption solar collector (DAC) and compares its performance with that of a typical flat-plate collector. Here a nanofluid-a mixture of water and aluminum nanoparticles—is used as the absorbing medium. A two-dimensional heat transfer analysis was developed in which direct sunlight was incident on a thin flowing film of nanofluid. The effects of absorption and scattering within the nanofluid were accounted for. In order to evaluate the temperature profile and intensity distribution within the nanofluid, the energy balance equation and heat transport equation were solved numerically. It was observed that the presence of nanoparticles increases the absorption of incident radiation by more than nine times over that of pure water. According to the results obtained from this study, under similar operating conditions, the efficiency of a DA C using nanofluid as the working fluid is found to be up to 10% higher (on an absolute basis) than that of a flat-plate collector. Generally a DAC using nanofluids as the working fluid performs better than a flat-plate collector, however, much better designed flat-plate collectors might be able to match or outperform a nanofluids based DAC under certain conditions.

Tunable light trapping for solar cells using localized surface plasmons

Abstract: Effective light management is imperative in maintaining high efficiencies as photovoltaic devices become thinner. We demonstrate a simple and effective method of enhancing light trapping in solar cells with thin absorber layers by tuning localized surface plasmons in arrays of Ag nanoparticles. By redshifting the surface plasmon resonances by up to 200 nm, through the modification of the local dielectric environment of the particles, we can increase the optical absorption in an underlying Si wafer fivefold at a wavelength of 1100 nm and enhance the external quantum efficiency of thin Si solar cells by a factor of 2.3 at this wavelength where transmission losses are prevalent. Additionally, by locating the nanoparticles on the rear of the solar cells, we can avoid absorption losses below the resonance wavelength due to interference effects, while still allowing long wavelength light to be coupled into the cell. Results from numerical simulations support the experimental findings and show that the fraction ...

Re-examination of the Size-Dependent Absorption Properties of CdSe Quantum Dots

Abstract: We investigate the size-dependent optical absorption coefficients of CdSe nanocrystals at both the band-edge and high within the absorption profile. The absorption properties in both of these regions must be self-consistent to ensure accuracy of the measured coefficients. By combining transmission electron microscopy and inductively coupled plasma−optical emission spectroscopy, we map out the optical absorption properties and establish reliable size-dependent band-edge calibration curves. The measured absorption properties are compared to a simple 0D confinement model, to classical theory based on light absorption by small particles in a dielectric medium and to state-of-the-art atomistic semiempirical pseudopotential modeling. The applicability of these newly established calibration curves is demonstrated by analyzing the nucleation and growth kinetics of CdSe nanocrystals in solution.

Attribution of aerosol light absorption to black carbon, brown carbon, and dust in China – interpretations of atmospheric measurements during EAST-AIRE

Abstract: . Black carbon, brown carbon, and mineral dust are three of the most important light absorbing aerosols. Their optical properties differ greatly and are distinctive functions of the wavelength of light. Most optical instruments that quantify light absorption, however, are unable to distinguish one type of absorbing aerosol from another. It is thus instructive to separate total absorption from these different light absorbers to gain a better understanding of the optical characteristics of each aerosol type. During the EAST-AIRE (East Asian Study of Tropospheric Aerosols: an International Regional Experiment) campaign near Beijing, we measured light scattering using a nephelometer, and light absorption using an aethalometer and a particulate soot absorption photometer. We also measured the total mass concentrations of carbonaceous (elemental and organic carbon) and inorganic particulates, as well as aerosol number and mass distributions. We were able to identify periods during the campaign that were dominated by dust, biomass burning, fresh (industrial) chimney plumes, other coal burning pollution, and relatively clean (background) air for Northern China. Each of these air masses possessed distinct intensive optical properties, including the single scatter albedo and Angstrom exponents. Based on the wavelength-dependence and particle size distribution, we apportioned total light absorption to black carbon, brown carbon, and dust; their mass absorption efficiencies at 550 nm were estimated to be 9.5, 0.5 (a lower limit value), and 0.03 m2/g, respectively. While agreeing with the common consensus that black carbon is the most important light absorber in the mid-visible, we demonstrated that brown carbon and dust could also cause significant absorption, especially at shorter wavelengths.

Dual band terahertz metamaterial absorber: Design, fabrication, and characterization

Abstract: We report the design, simulation, and measurement of a dual-band metamaterial absorber in the terahertz region. Theoretical and experimental results show that the absorber has two distinct and strong absorption points near 0.45 and 0.92 THz, both which are related to the LC resonance of the metamaterial. The distributions of the power flow and the power loss indicate that the absorber is an excellent electromagnetic wave collector: the wave is first trapped and reinforced in certain specific locations and then completely consumed. This dual-band absorber has applications in many scientific and technological areas.

Carbon dioxide postcombustion capture: a novel screening study of the carbon dioxide absorption performance of 76 amines

Abstract: The significant and rapid reduction of greenhouse gas emissions is recognized as necessary to mitigate the potential climate effects from global warming. The postcombustion capture (PCC) and storage of carbon dioxide (CO2) produced from the use of fossil fuels for electricity generation is a key technology needed to achieve these reductions. The most mature technology for CO2 capture is reversible chemical absorption into an aqueous amine solution. In this study the results from measurements of the CO2 absorption capacity of aqueous amine solutions for 76 different amines are presented. Measurements were made using both a novel isothermal gravimetric analysis (IGA) method and a traditional absorption apparatus. Seven amines, consisting of one primary, three secondary, and three tertiary amines, were identified as exhibiting outstanding absorption capacities. Most have a number of structural features in common including steric hindrance and hydroxyl functionality 2 or 3 carbons from the nitrogen. Initial CO2 absorption rate data from the IGA measurements was also used to indicate relative absorption rates. Most of the outstanding performers in terms of capacity also showed initial absorption rates comparable to the industry standard monoethanolamine (MEA). This indicates, in terms of both absorption capacity and kinetics, that they are promising candidates for further investigation.

Achieving λ/20 Resolution by One-Color Initiation and Deactivation of Polymerization

Abstract: In conventional photolithography, diffraction limits the resolution to about one-quarter of the wavelength of the light used. We introduce an approach to photolithography in which multiphoton absorption of pulsed 800-nanometer (nm) light is used to initiate cross-linking in a polymer photoresist and one-photon absorption of continuous-wave 800-nm light is used simultaneously to deactivate the photopolymerization. By employing spatial phase-shaping of the deactivation beam, we demonstrate the fabrication of features with scalable resolution along the beam axis, down to a 40-nm minimum feature size. We anticipate application of this technique for the fabrication of diverse two- and three-dimensional structures with a feature size that is a small fraction of the wavelength of the light employed.

Optical absorption enhancement in silicon nanowire arrays with a large lattice constant for photovoltaic applications.

Abstract: In this paper, we use the transfer matrix method to calculate the optical absorptance of vertically-aligned silicon nanowire (SiNW) arrays. For fixed filling ratio, significant optical absorption enhancement occurs when the lattice constant is increased from 100 nm to 600 nm. The enhancement arises from an increase in field concentration within the nanowire as well as excitation of guided resonance modes. We quantify the absorption enhancement in terms of ultimate efficiency. Results show that an optimized SiNW array with lattice constant of 600 nm and wire diameter of 540 nm has a 72.4% higher ultimate efficiency than a Si thin film of equal thickness. The enhancement effect can be maintained over a large range of incidence angles.

X-ray absorption spectroscopy

Abstract: This review gives a brief description of the theory and application of X-ray absorption spectroscopy, both X-ray absorption near-edge structure (XANES) and extended X-ray absorption fine structure (EXAFS), especially, pertaining to photosynthesis. The advantages and limitations of the methods are discussed. Recent advances in extended EXAFS and polarized EXAFS using oriented membranes and single crystals are explained. Developments in theory in understanding the XANES spectra are described. The application of X-ray absorption spectroscopy to the study of the Mn4Ca cluster in Photosystem II is presented.

Plasmonic Enhancement or Energy Transfer? On the Luminescence of Gold-, Silver-, and Lanthanide-Doped Silicate Glasses and Its Potential for Light-Emitting Devices

Abstract: With the technique of synchrotron X-ray activation, molecule-like, non-plasmonic gold and silver particles in soda-lime silicate glasses can be generated. The luminescence energy transfer between these species and Ianthanide(III) ions is studied. As a result, a significant lanthanide luminescence enhancement by a factor of up to 250 under non-resonant UV excitation is observed. The absence of a distinct gold and silver plasmon resonance absorption, respectively, the missing nanoparticle signals in previous SAXS and TEM experiments, the unaltered luminescence lifetime of the lanthanide ions compared to the non-enhanced case, and an excitation maximum at 300―350 nm (equivalent to the absorption range of small noble metal particles) indicate unambiguously that the observed enhancement is due to a classical energy transfer between small noble metal particles and lanthanide ions, and not to a plasmonic field enhancement effect. It is proposed that very small, molecule-like noble metal particles (such as dimers, trimers, and tetramers) first absorb the excitation light, undergo a singlet-triplet intersystem crossing, and finally transfer the energy to an excited multiplet state of adjacent lanthanide(III) ions. X-ray lithographic microstructuring and excitation with a commercial UV LED show the potential of the activated glass samples as bright light-emitting devices with tunable emission colors.

Improved red-response in thin film a-Si:H solar cells with soft-imprinted plasmonic back reflectors

Abstract: The impact of controlled nanopatterning on the Ag back contact of an n-i-p a-Si:H solar cell was investigated experimentally and through electromagnetic simulation. Compared to a similar reference cell with a flat back contact, we demonstrate an efficiency increase from 4.5% to 6.2%, with a 26% increase in short circuit current density. Spectral response measurements show the majority of the improvement between 600 and 800 nm, with no reduction in photocurrent at wavelengths shorter than 600 nm. Optimization of the pattern aspect ratio using electromagnetic simulation predicts absorption enhancements over 50% at 660 nm.

Si nanopillar array optimization on Si thin films for solar energy harvesting

Abstract: In this letter, Si thin film (800 nm thick) with nanopillar array decorated surface is studied via simulation for its solar energy absorption characteristics. It is found that the light absorption is significantly enhanced due to the adding of the Si nanopillar (SiNP) array to the Si thin film. The absorption characteristics of the SiNP structure would be approximately optimum (especially at ∼2.5 eV, the high energy density region in the solar spectrum) when the periodicity of SiNP array is set as ∼500 nm, which can be explained when comparing the incident light wavelength with the periodicity of SiNP array.

Photochromic fluorescence switching from diarylethenes and its applications

Abstract: The review describes the photochromic and fluorescent characteristics of various diarylethene (DAET) derivatives, and presents recent research into their applications. This comprises a discussion of the optical characteristics of some DAET-based molecules exhibiting red, green, or blue (RGB) colors or fluorescence. Molecular calculations of the optical properties of DAET interpret intriguing experimental observations and predict photochemical or photophysical properties. In particular, stabilization of HOMO in the BTFO n ( n = 1, 2, 3, 4) increases the energy difference between the HOMO and the LUMO, which leads to the blue-shift of absorption and emission bands as the number of oxygen attached to sulfur ( n ) increases. Various devices and application studies have been designed as photon-mode systems based on photochemical control of the fluorescence energy. The photochromic DAET materials have shown promise as optical data storage, switching devices, and biological applications such as the development of biomaterial sensors, analysis of biological dynamics, and live cell imaging.

Determination of energy band gap of nanocrystalline SbSI using diffuse reflectance spectroscopy.

Abstract: Twelve methods of determining energy band gap (Eg) of semiconductors using diffuse reflectance spectroscopy have been applied in investigations of sonochemically produced antimony sulfoiodide (SbSI) consisting of nanowires. It has been proved that the best method of determining Eg is based on simultaneous fitting of many mechanisms of absorption to the spectral dependence of Kubelka–Munk function evaluated from the diffuse reflectance data. It allows determining the values of indirect forbidden Eg, the Urbach energy, and the constant absorption/scattering of the examined semiconductor.

Nanoparticles for photoacoustic imaging

Abstract: Nanoparticles have been designed and applied as contrast enhancers in various optical imaging techniques, such as optical coherence tomography, fluorescence imaging, and optical reflectance microscopy. As an emerging hybrid imaging modality, photoacoustic imaging (PAI) has also benefited from the application of these nanoparticle-based contrast agents. We review this rapidly growing field and describe the applications of nanoparticles in PAI. Particular focus is given to nanoparticles whose absorption mechanism is based on surface plasmon resonance, including gold nanoshells, nanorods, and nanocages. Dye-embedded nanoparticles are also reviewed. Specifically, the design and application of each nanoparticle-based contrast agent in relation to the field of PAI are detailed.

Selective positioning of organic dyes in a mesoporous inorganic oxide film

Abstract: Although sequential adsorption of dyes in a single TiO2 electrode is ideal to extend the range of light absorption in dye-sensitized solar cells, high-temperature processing has so far limited its application. We report a method for selective positioning of organic dye molecules with different absorption ranges in a mesoporous TiO2 film by mimicking the concept of the stationary phase and the mobile phase in column chromatography, where polystyrene-filled mesoporous TiO2 film is explored for use as a stationary phase and a Bronsted-base-containing polymer solution is developed for use as a mobile phase for selective desorption of the adsorbed dye. By controlling the desorption and adsorption depth, yellow, red and green dyes were vertically aligned within a TiO2 film, which is confirmed by an electron probe micro-analyser. The external quantum efficiency (EQE) spectrum from a solar cell with three selectively positioned dyes reveals the EQE characteristics of each single-dye cell. Although sequential adsorption of dyes in TiO2 electrodes is ideal for extending the range of light absorption in dye-sensitized solar cells, high-temperature processing has so far limited its application. A method for the selective positioning of organic dye molecules with different absorption ranges is now reported in a mesoporous inorganic oxide film.

Spectrally based remote sensing of river bathymetry

Abstract: This paper evaluates the potential for remote mapping of river bathymetry by (1) examining the theoretical basis of a simple, ratio-based technique for retrieving depth information from passive optical image data; (2) performing radiative transfer simulations to quantify the effects of suspended sediment concentration, bottom reflectance, and water surface state; (3) assessing the accuracy of spectrally based depth retrieval under field conditions via ground-based reflectance measurements; and (4) producing bathymetric maps for a pair of gravel-bed rivers from hyperspectral image data. Consideration of the relative magnitudes of various radiance components allowed us to define the range of conditions under which spectrally based depth retrieval is appropriate: the remotely sensed signal must be dominated by bottom-reflected radiance. We developed a simple algorithm, called optimal band ratio analysis (OBRA), for identifying pairs of wavelengths for which this critical assumption is valid and which yield strong, linear relationships between an image-derived quantity X and flow depth d. OBRA of simulated spectra indicated that water column optical properties were accounted for by a shorter-wavelength numerator band sensitive to scattering by suspended sediment while depth information was provided by a longer-wavelength denominator band subject to strong absorption by pure water. Field spectra suggested that bottom reflectance was fairly homogeneous, isolating the effect of depth, and that radiance measured above the water surface was primarily reflected from the bottom, not the water column. OBRA of these data, 28% of which were collected during a period of high turbidity, yielded strong X versus d relations (R2 from 0·792 to 0·976), demonstrating that accurate depth retrieval is feasible under field conditions. Moreover, application of OBRA to hyperspectral image data resulted in spatially coherent, hydraulically reasonable bathymetric maps, though negative depth estimates occurred along channel margins where pixels were mixed. This study indicates that passive optical remote sensing could become a viable tool for measuring river bathymetry. Copyright © 2009 John Wiley & Sons, Ltd.

Plasmonic absorption enhancement in organic solar cells with thin active layers

Abstract: The influence of silver nanoparticles on light absorption in organic solar cells based on poly(3-exylthiophene):(6,6)-phenyl-C61-butyric-acid-methyl ester is studied by means of finite element method simulations. The metallic nanoparticles are embedded directly inside the active layer. We investigate the enhancement mechanism and the influence of factors such as the spacing between neighboring nanoparticles, the particle diameter, and the coating thickness. The plasmonic resonance of the particles has a wideband influence on the absorption, and we observe a rich interaction between plasmonic enhancement and the absorption characteristics of the active layer material. An enhancement with a factor of around 1.56 is observed for nanoparticles with a diameter of 24 nm and a spacing of 40 nm, bringing the structure to the absorption level of much thicker active layers without nanoparticles. In addition, a significant effect of the particle coating thickness is observed.

Enhanced Light Absorption and Scattering by Carbon Soot Aerosol Internally Mixed with Sulfuric Acid

Abstract: Light absorption by carbon soot increases when the particles are internally mixed with nonabsorbing materials, leading to increased radiative forcing, but the magnitude of this enhancement is a subject of great uncertainty. We have performed laboratory experiments of the optical properties of fresh and internally mixed carbon soot aerosols with a known particle size, morphology, and the mixing state. Flame-generated soot aerosol is size-selected with a double-differential mobility analyzer (DMA) setup to eliminate multiply charged particle modes and then exposed to gaseous sulfuric acid (109−1010 molecule cm−3) and water vapor (5−80% relative humidity, RH). Light extinction and scattering by fresh and internally mixed soot aerosol are measured at 532 nm wavelength using a cavity ring-down spectrometer and an integrating nephelometer, respectively, and the absorption is derived as the difference between extinction and scattering. The optical properties of fresh soot are independent of RH, whereas soot inte...