Fabrication and characterization of 3D printed BaTiO3/PVDF nanocomposites:
Reads0
Chats0
TLDR
In this paper, a fabrication process to enhance homogeneous dispersion of BaTiO3 nanoparticles in polyvinylidene fluoride matrix nanocomposites using fused deposition modeling (FDM) 3D printin...Abstract:
This paper presents a fabrication process to enhance homogeneous dispersion of BaTiO3 nanoparticles in polyvinylidene fluoride matrix nanocomposites using fused deposition modeling (FDM) 3D printin...read more
Citations
More filters
Journal ArticleDOI
Additive Manufacturing of Piezoelectric Materials
Cheng Chen,Wang Xi,Yan Wang,Dandan Yang,Fangyi Yao,Wenxiong Zhang,Bo Wang,Galhenage A. Sewvandi,Desuo Yang,Dengwei Hu +9 more
Journal ArticleDOI
New developments in composites, copolymer technologies and processing techniques for flexible fluoropolymer piezoelectric generators for efficient energy harvesting
Nick A. Shepelin,Alexey M. Glushenkov,Vanessa C. Lussini,Phillip John South Melbourne Fox,Greg W. Dicinoski,Joseph G. Shapter,Amanda V. Ellis +6 more
TL;DR: In this article, a critical review of the processing of fluoropolymers towards the maximization of piezoelectric conversion parameters is presented, focusing on the correlation between synthetic routes, inclusion of further co-monomers, addition of additives and nanomaterials, as well as processing techniques and the optimized electricity generation in the resultant PEGs.
Journal ArticleDOI
Integrated 3D printing and corona poling process of PVDF piezoelectric films for pressure sensor application
TL;DR: Li et al. as discussed by the authors proposed an integrated 3D printing process with corona poling to fabricate piezoelectric polyvinylidene fluoride (PVDF) sensors without post poling process.
Journal ArticleDOI
3D-printed multifunctional materials enabled by artificial-intelligence-assisted fabrication technologies
TL;DR: In this article, the authors present a review of ex- situ and in situ artificial intelligence-assisted 3D printing of multifunctional materials and its combination with surgical robots to enable autonomous medical care and smart biomanufacturing.
Journal ArticleDOI
The trends and challenges of fiber reinforced additive manufacturing
Ismail Fidan,Astrit Imeri,Ankit Gupta,Seymur Hasanov,Aslan Nasirov,Amy M. Elliott,Frank Alifui-Segbaya,Norimichi Nanami +7 more
TL;DR: The current trends and challenges that FRAM is bringing to AM ecosystem are reported, including the impact of fiber orientations and fraction on the performance of parts, improving the printing parameters, and other subjects.
References
More filters
Journal ArticleDOI
Additive manufacturing of carbon fiber reinforced thermoplastic composites using fused deposition modeling
TL;DR: In this article, a carbon fiber reinforced plastic (CFRP) composite is used for Fused Deposition Modeling (FDM) of thermoplastic matrix CFRP composites.
MonographDOI
An introduction to numerical analysis
Endre Süli,David F. Mayers +1 more
TL;DR: In this article, a wide range of computational problems ranging from the approximation of functions and integrals to the approximate solution of algebraic, transcendental, differential and integral equations are discussed.
Journal ArticleDOI
Ftir studies of -phase crystal formation in stretched pvdf films
A Salimi,A A Yousefi +1 more
TL;DR: In this article, the appearance of β-phase in compression molded films of two different grades of poly vinylidene fluoride (PVDF) resin was analyzed using FTIR spectra.
Journal ArticleDOI
A critical analysis of the α, β and γ phases in poly(vinylidene fluoride) using FTIR
TL;DR: In this article, a universal phase identification procedure using only the Fourier transform infrared spectroscopy (FTIR) results is proposed and validated, which can differentiate the three phases by checking the bands around 763 and/or 614, 1275, and 1234 cm−1 for the α, β and γ phases, respectively.
Journal ArticleDOI
Effect of crystalline phase, orientation and temperature on the dielectric properties of poly (vinylidene fluoride) (PVDF)
Rinaldo Gregorio,E. M. Ueno +1 more
TL;DR: In this article, the effect of crystalline phase, uniaxial drawing and temperature on the real (e′) and imaginary (e″) parts of the relative complex permittivity of poly (vinylidene fluoride) (PVDF) was studied in the frequency range between 102 and 106 Hz.