Showing papers on "Supercapacitor published in 2017"
TL;DR: This work shows that Ni3(2,3,6,7,10,11-hexaiminotriphenylene)2 (Ni3(HITP)2), a MOF with high electrical conductivity, can serve as the sole electrode material in an EDLC, the first example of a supercapacitor made entirely from neat MOFs as active materials, without conductive additives or other binders.
Abstract: Using MOFs as active electrodes in electrochemical double layer capacitors has so far proved difficult. An electrically conductive MOF used as an electrode is now shown to exhibit electrochemical performance similar to most carbon-based materials. Owing to their high power density and superior cyclability relative to batteries, electrochemical double layer capacitors (EDLCs) have emerged as an important electrical energy storage technology that will play a critical role in the large-scale deployment of intermittent renewable energy sources, smart power grids, and electrical vehicles1,2,3. Because the capacitance and charge–discharge rates of EDLCs scale with surface area and electrical conductivity, respectively, porous carbons such as activated carbon, carbon nanotubes and crosslinked or holey graphenes are used exclusively as the active electrode materials in EDLCs4,5,6,7,8,9. One class of materials whose surface area far exceeds that of activated carbons, potentially allowing them to challenge the dominance of carbon electrodes in EDLCs, is metal–organic frameworks (MOFs)10. The high porosity of MOFs, however, is conventionally coupled to very poor electrical conductivity, which has thus far prevented the use of these materials as active electrodes in EDLCs. Here, we show that Ni3(2,3,6,7,10,11-hexaiminotriphenylene)2 (Ni3(HITP)2), a MOF with high electrical conductivity11, can serve as the sole electrode material in an EDLC. This is the first example of a supercapacitor made entirely from neat MOFs as active materials, without conductive additives or other binders. The MOF-based device shows an areal capacitance that exceeds those of most carbon-based materials and capacity retention greater than 90% over 10,000 cycles, in line with commercial devices. Given the established structural and compositional tunability of MOFs, these results herald the advent of a new generation of supercapacitors whose active electrode materials can be tuned rationally, at the molecular level.
1,597 citations
TL;DR: In this article, a strategy to prepare flexible and conductive MXene/graphene (reduced graphene oxide, rGO) supercapacitor electrodes by using electrostatic self-assembly between positively charged rGO modified with poly(diallyldimethylammonium chloride) and negatively charged titanium carbide MXene nanosheets is presented.
Abstract: A strategy to prepare flexible and conductive MXene/graphene (reduced graphene oxide, rGO) supercapacitor electrodes by using electrostatic self-assembly between positively charged rGO modified with poly(diallyldimethylammonium chloride) and negatively charged titanium carbide MXene nanosheets is presented. After electrostatic assembly, rGO nanosheets are inserted in-between MXene layers. As a result, the self-restacking of MXene nanosheets is effectively prevented, leading to a considerably increased interlayer spacing. Accelerated diffusion of electrolyte ions enables more electroactive sites to become accessible. The freestanding MXene/rGO-5 wt% electrode displays a volumetric capacitance of 1040 F cm−3 at a scan rate of 2 mV s−1 , an impressive rate capability with 61% capacitance retention at 1 V s−1 and long cycle life. Moreover, the fabricated binder-free symmetric supercapacitor shows an ultrahigh volumetric energy density of 32.6 Wh L−1, which is among the highest values reported for carbon and MXene based materials in aqueous electrolytes. This work provides fundamental insight into the effect of interlayer spacing on the electrochemical performance of 2D hybrid materials and sheds light on the design of next-generation flexible, portable and highly integrated supercapacitors with high volumetric and rate performances.
1,260 citations
TL;DR: Various application of ILs are reviewed by focusing on their use as electrolyte materials for Li/Na ion batteries, Li-sulfur batteries,Li-oxygen batteries, and nonhumidifiedfuel cells and as carbon precursors for electrode catalysts of fuel cells and electrode materials for batteries and supercapacitors.
Abstract: Ionic liquids (ILs) are liquids consisting entirely of ions and can be further defined as molten salts having melting points lower than 100 °C. One of the most important research areas for IL utilization is undoubtedly their energy application, especially for energy storage and conversion materials and devices, because there is a continuously increasing demand for clean and sustainable energy. In this article, various application of ILs are reviewed by focusing on their use as electrolyte materials for Li/Na ion batteries, Li-sulfur batteries, Li-oxygen batteries, and nonhumidified fuel cells and as carbon precursors for electrode catalysts of fuel cells and electrode materials for batteries and supercapacitors. Due to their characteristic properties such as nonvolatility, high thermal stability, and high ionic conductivity, ILs appear to meet the rigorous demands/criteria of these various applications. However, for further development, specific applications for which these characteristic properties becom...
1,096 citations
TL;DR: In this article, the authors present the recent advances in the field of composite materials that include at least one carbon-based component for supercapacitor electrodes, focusing on cases in which a single material by itself suffers from a drawback that can be overcome by combining it with other components, enabling the fabrication of a composite material with enhanced performance.
Abstract: Electrochemical capacitors, so-called supercapacitors, play an important role in energy storage and conversion systems. In the last decade, with the increasing volume of scientific activity and publications in this field, researchers have developed better tools to improve electrode materials. Although carbonaceous materials seem the most suitable for supercapacitor applications, a large diversity of materials has been proposed and studied. Yet, in order to accomplish performance beyond the limitations of each material, mainly in terms of energy density and durability, composite materials have been implemented, most of them being the combinations of carbon-based materials and other components. In this review, we present the recent advances in the field of composite materials that include at least one carbon-based component for supercapacitor electrodes. We focus on cases in which a single material by itself suffers from a drawback that can be overcome by combining it with other components, enabling the fabrication of a composite material with enhanced performance. We present several important compositions as well as the major routes of synthesis, characterization and performance of composite materials in this field.
1,042 citations
TL;DR: In this article, a one-step strategy to synthesize three-dimensional porous graphitic biomass carbon (PGBC) from bamboo char (BC), and studied its electrochemical performance as electrode materials for supercapacitors.
775 citations
Book•
10 Nov 2017TL;DR: The limitations and challenges of nanostructured materials while being used for solar cells, lithium ion batteries, supercapacitors, and hydrogen storage systems have also been addressed in this review.
Abstract: Nanostructured materials are advantageous in offering huge surface to volume ratios, favorable transport properties, altered physical properties, and confinement effects resulting from the nanoscale dimensions, and have been extensively studied for energy-related applications such as solar cells, catalysts, thermoelectrics, lithium ion batteries, supercapacitors, and hydrogen storage systems. This review focuses on a few select aspects regarding these topics, demonstrating that nanostructured materials benefit these applications by (1) providing a large surface area to boost the electrochemical reaction or molecular adsorption occurring at the solid–liquid or solid–gas interface, (2) generating optical effects to improve optical absorption in solar cells, and (3) giving rise to high crystallinity and/or porous structure to facilitate the electron or ion transport and electrolyte diffusion, so as to ensure the electrochemical process occurs with high efficiency. It is emphasized that, to further enhance the capability of nanostructured materials for energy conversion and storage, new mechanisms and structures are anticipated. In addition to highlighting the obvious advantages of nanostructured materials, the limitations and challenges of nanostructured materials while being used for solar cells, lithium ion batteries, supercapacitors, and hydrogen storage systems have also been addressed in this review.
767 citations
TL;DR: Collectively, the Ti3 C2 Tx films are among the state-of-the-art for future transparent, conductive, capacitive electrodes, and translate into technologically viable devices for next-generation wearable, portable electronics.
Abstract: 2D transition-metal carbides and nitrides, known as MXenes, have displayed promising properties in numerous applications, such as energy storage, electromagnetic interference shielding, and catalysis. Titanium carbide MXene (Ti3 C2 Tx ), in particular, has shown significant energy-storage capability. However, previously, only micrometer-thick, nontransparent films were studied. Here, highly transparent and conductive Ti3 C2 Tx films and their application as transparent, solid-state supercapacitors are reported. Transparent films are fabricated via spin-casting of Ti3 C2 Tx nanosheet colloidal solutions, followed by vacuum annealing at 200 °C. Films with transmittance of 93% (≈4 nm) and 29% (≈88 nm) demonstrate DC conductivity of ≈5736 and ≈9880 S cm-1 , respectively. Such highly transparent, conductive Ti3 C2 Tx films display impressive volumetric capacitance (676 F cm-3 ) combined with fast response. Transparent solid-state, asymmetric supercapacitors (72% transmittance) based on Ti3 C2 Tx and single-walled carbon nanotube (SWCNT) films are also fabricated. These electrodes exhibit high capacitance (1.6 mF cm-2 ) and energy density (0.05 µW h cm-2 ), and long lifetime (no capacitance decay over 20 000 cycles), exceeding that of graphene or SWCNT-based transparent supercapacitor devices. Collectively, the Ti3 C2 Tx films are among the state-of-the-art for future transparent, conductive, capacitive electrodes, and translate into technologically viable devices for next-generation wearable, portable electronics.
751 citations
TL;DR: In this paper, a hollow particle-based nitrogen-doped carbon nanofibers (HPCNFs-N) is proposed for supercapacitors, which is composed of interconnected carbon hollow nanoparticles.
Abstract: Carbon-based materials, as one of the most important electrode materials for supercapacitors, have attracted tremendous attention. At present, it is highly desirable but remains challenging to prepare one-dimensional carbon complex hollow nanomaterials for further improving the performance of supercapacitors. Herein, we report an effective strategy for the synthesis of hollow particle-based nitrogen-doped carbon nanofibers (HPCNFs-N). By embedding ultrafine zeolitic imidazolate framework (ZIF-8) nanoparticles into electrospun polyacrylonitrile (PAN), the as-prepared composite nanofibers are carbonized into hierarchical porous nanofibers composed of interconnected nitrogen-doped carbon hollow nanoparticles. Owing to its unique structural feature and the desirable chemical composition, the derived HPCNFs-N material exhibits much enhanced electrochemical properties as an electrode material for supercapacitors with remarkable specific capacitance at various current densities, high energy/power density and long cycling stability over 10 000 cycles.
745 citations
TL;DR: The material design strategies in Li-ion and Na-ion capacitors are summarized, with a focus on pseudocapacitive oxide anodes (Nb2 O5 , MoO3 , etc.), which provide a new opportunity to obtain a higher power density of the hybrid devices.
Abstract: Hybrid metal-ion capacitors (MICs) (M stands for Li or Na) are designed to deliver high energy density, rapid energy delivery, and long lifespan. The devices are composed of a battery anode and a supercapacitor cathode, and thus become a tradeoff between batteries and supercapacitors. In the past two decades, tremendous efforts have been put into the search for suitable electrode materials to overcome the kinetic imbalance between the battery-type anode and the capacitor-type cathode. Recently, some transition-metal compounds have been found to show pseudocapacitive characteristics in a nonaqueous electrolyte, which makes them interesting high-rate candidates for hybrid MIC anodes. Here, the material design strategies in Li-ion and Na-ion capacitors are summarized, with a focus on pseudocapacitive oxide anodes (Nb2 O5 , MoO3 , etc.), which provide a new opportunity to obtain a higher power density of the hybrid devices. The application of Mxene as an anode material of MICs is also discussed. A perspective to the future research of MICs toward practical applications is proposed to close.
664 citations
TL;DR: This review presents an overview of porous 1D nanostructure research, from the synthesis by bottom-up and top-down approaches with rational and controllable structures, to several important electrochemical energy storage applications including lithium-ion batteries, sodium-ion lithium-sulfur batteries, lithium-oxygen batteries and supercapacitors.
Abstract: Electrochemical energy storage technology is of critical importance for portable electronics, transportation and large-scale energy storage systems. There is a growing demand for energy storage devices with high energy and high power densities, long-term stability, safety and low cost. To achieve these requirements, novel design structures and high performance electrode materials are needed. Porous 1D nanomaterials which combine the advantages of 1D nanoarchitectures and porous structures have had a significant impact in the field of electrochemical energy storage. This review presents an overview of porous 1D nanostructure research, from the synthesis by bottom-up and top-down approaches with rational and controllable structures, to several important electrochemical energy storage applications including lithium-ion batteries, sodium-ion batteries, lithium-sulfur batteries, lithium-oxygen batteries and supercapacitors. Highlights of porous 1D nanostructures are described throughout the review and directions for future research in the field are discussed at the end.
582 citations
TL;DR: An aqueous hybrid supercapacitor based on the iron oxide hydroxide anode shows stability during float voltage test for 450 h and an energy density of 104 Wh kg−1 at a power density of 1.27 kW kg−1.
Abstract: Carbon materials are generally preferred as anodes in supercapacitors; however, their low capacitance limits the attained energy density of supercapacitor devices with aqueous electrolytes. Here, we report a low-crystalline iron oxide hydroxide nanoparticle anode with comprehensive electrochemical performance at a wide potential window. The iron oxide hydroxide nanoparticles present capacitances of 1,066 and 716 F g−1 at mass loadings of 1.6 and 9.1 mg cm−2, respectively, a rate capability with 74.6% of capacitance retention at 30 A g−1, and cycling stability retaining 91% of capacitance after 10,000 cycles. The performance is attributed to a dominant capacitive charge-storage mechanism. An aqueous hybrid supercapacitor based on the iron oxide hydroxide anode shows stability during float voltage test for 450 h and an energy density of 104 Wh kg−1 at a power density of 1.27 kW kg−1. A packaged device delivers gravimetric and volumetric energy densities of 33.14 Wh kg−1 and 17.24 Wh l−1, respectively. Carbons dominate anode materials for supercapacitors, however the attained energy density remains low. Here the authors fabricate low-crystalline iron oxide-hydroxide nanoparticle anodes with good electrochemical characteristics, exhibiting high stability and energy/power densities in a hybrid supercapacitor.
TL;DR: In this article, an all-wood-structured asymmetric supercapacitor (ASC) based on an activated wood carbon (AWC) anode, a wood membrane separator and a MnO2/wood carbon (MnO2@WC) cathode is presented.
Abstract: In energy storage devices, the critical demands for high energy/power density, low cost, long cycle lives and environmental friendliness have highlighted an urgent need for developing storage electrodes with low cost, large thickness, high mass loading, low tortuosity and high energy/power density. Here we demonstrate the design and construction of an all-wood-structured asymmetric supercapacitor (ASC) based on an activated wood carbon (AWC) anode, a wood membrane separator and a MnO2/wood carbon (MnO2@WC) cathode. The structural virtues of the all-wood-structured ASC device – desirable thickness (up to ∼1 mm), direct channels with low tortuosity, high electronic and ionic conductivity – enable ASC high areal mass loadings (up to 30 mg cm−2 for the anode and 75 mg cm−2 for the wood carbon/MnO2 composite cathode), a high energy density of 1.6 mW h cm−2 and a maximum power density of 24 W cm−2, representing the highest mass loading and areal energy/power densities among all reported MnO2-based supercapacitors. Moreover, all components in the all-wood-structured ASC are low-cost, environmentally friendly and biocompatible. With these unique features, the all-wood-structured ASC represents a promising energy storage device to realize high mass loading, high energy/power density, and biocompatibility for green and renewable energy storage.
TL;DR: In this paper, a green hybrothermal method was used to functionalize CFF with coral-like MnO2 nanostructures to improve the pseudocapacitance properties of the hybrid composites.
TL;DR: In this article, a method to significantly improve the gravimetric capacitance of Ti3C2Tx MXenes by cation intercalation and surface modification is reported, and the as-prepared electrodes show above 99% retention over 10 000 cycles.
Abstract: Supercapacitors attract great interest because of the increasing and urgent demand for environment-friendly high-power energy sources. Ti3C2, a member of MXene family, is a promising electrode material for supercapacitors owing to its excellent chemical and physical properties. However, the highest gravimetric capacitance of the MXene-based electrodes is still relatively low (245 F g−1) and the key challenge to improve this is to exploit more pseudocapacitance by increasing the active site concentration. Here, a method to significantly improve the gravimetric capacitance of Ti3C2Tx MXenes by cation intercalation and surface modification is reported. After K+ intercalation and terminal groups (OH−/F−) removing , the intercalation pseudocapacitance is three times higher than the pristine MXene, and MXene sheets exhibit a significant enhancement (about 211% of the origin) in the gravimetric capacitance (517 F g−1 at a discharge rate of 1 A g−1). Moreover, the as-prepared electrodes show above 99% retention over 10 000 cycles. This improved electrochemical performance is attributed to the large interlayer voids of Ti3C2 and lowest terminated surface group concentration. This study demonstrates a new strategy applicable to other MXenes (Ti2CTx, Nb2CTx, etc.) in maximizing their potential applications in energy storage.
TL;DR: In this paper, a 3D-networked, ultrathin, and porous Ni3S2/CoNi2S4 on Ni foam (NF) was successfully designed and synthesized by a simple sulfidation process from 3D Ni-Co precursors.
Abstract: 3D-networked, ultrathin, and porous Ni3S2/CoNi2S4 on Ni foam (NF) is successfully designed and synthesized by a simple sulfidation process from 3D Ni–Co precursors. Interestingly, the edge site-enriched Ni3S2/CoNi2S4/NF 3D-network is realized by the etching-like effect of S2− ions, which made the surfaces of Ni3S2/CoNi2S4/NF with a ridge-like feature. The intriguing structural/compositional/componental advantages endow 3D-networked-free-standing Ni3S2/CoNi2S4/NF electrodes better electrochemical performance with specific capacitance of 2435 F g−1 at a current density of 2 A g−1 and an excellent rate capability of 80% at 20 A g−1. The corresponding asymmetric supercapacitor achieves a high energy density of 40.0 W h kg−1 at an superhigh power density of 17.3 kW kg−1, excellent specific capacitance (175 F g−1 at 1A g−1), and electrochemical cycling stability (92.8% retention after 6000 cycles) with Ni3S2/CoNi2S4/NF as the positive electrode and activated carbon/NF as the negative electrode. Moreover, the temperature dependences of cyclic voltammetry curve polarization and specific capacitances are carefully investigated, and become more obvious and higher, respectively, with the increase of test temperature. These can be attributed to the components' synergetic effect assuring rich redox reactions, high conductivity as well as highly porous but robust architectures. This work provides a general, low-cost route to produce high performance electrode materials for portable supercapacitor applications on a large scale.
TL;DR: A review of recent literature on electrochemical energy storage (EES) technologies, focusing on supercapacitor and also supercapattery which is a generic term for various hybrid devices combining the merits of rechargeable battery and supercapACitor is presented in this paper.
Abstract: This article reviews critically selected recent literature on electrochemical energy storage (EES) technologies, focusing on supercapacitor and also supercapattery which is a generic term for various hybrid devices combining the merits of rechargeable battery and supercapacitor. Fundamentals of EES are explained, aiming at clarification of some literature confusions such as the differences between capacitive and non-capacitive Faradaic charge storage mechanisms, and between cathode and positive electrode (positrode), and between anode and negative electrode (negatrode). In particular, the concept and origin of pseudocapacitance are qualitatively correlated with the band model for semiconductors. Strategies for design and construction of supercapattery are discussed in terms of both the materials structures and device engineering. Selection of materials, including electrolytes, is another topic reviewed selectively. Graphenes and carbon nanotubes are the favourable choice to composite with both cap...
TL;DR: In this paper, high-defect porous carbons with high specific surface area and high defect density have been prepared through direct carbonization of cattle bones without any additional activators and templates.
TL;DR: A comprehensive review on recent progress of the synthesis and modification ofTiO2 nanotubes to be used for photo/photoelectro‐catalytic water splitting and the future development of TiO2 Nanotubes is discussed.
Abstract: Hydrogen production from water splitting by photo/photoelectron-catalytic process is a promising route to solve both fossil fuel depletion and environmental pollution at the same time. Titanium dioxide (TiO2) nanotubes have attracted much interest due to their large specific surface area and highly ordered structure, which has led to promising potential applications in photocatalytic degradation, photoreduction of CO2, water splitting, supercapacitors, dye-sensitized solar cells, lithium-ion batteries and biomedical devices. Nanotubes can be fabricated via facile hydrothermal method, solvothermal method, template technique and electrochemical anodic oxidation. In this report, we provide a comprehensive review on recent progress of the synthesis and modification of TiO2 nanotubes to be used for photo/photoelectro-catalytic water splitting. The future development of TiO2 nanotubes is also discussed.
TL;DR: An effective new approach is demonstrated, which can extend the understanding of structure-performance relationships for many electrochemical energy-storage systems and form a significant complement to classical electrochemical impedance spectroscopy.
Abstract: 3D few-layer graphene-like carbon with hierarchical open porous architecture is obtained by a new in situ Cu template method, leading to top-level supercapacitive performance, especially state-of-the-art power density. An effective new approach is demonstrated, which can extend the understanding of structure-performance relationships for many electrochemical energy-storage systems and form a significant complement to classical electrochemical impedance spectroscopy.
TL;DR: In this paper, the authors present state of the art of renewable carbon materials derived from natural biomasses with an emphasis on their applications in supercapacitors and lithium-sulfur batteries.
Abstract: Electrochemical energy storage devices, such as supercapacitors and batteries, have been proven to be the most effective energy conversion and storage technologies for practical application. However, further development of these energy storage devices is hindered by their poor electrode performance. Carbon materials used in supercapacitors and batteries are often derived from nonrenewable resources under harsh environments. Naturally abundant biomass is a green, alternative carbon source with many desired properties. This review article presents state of the art of renewable carbon materials derived from natural biomasses with an emphasis on their applications in supercapacitors and lithium–sulfur batteries.
TL;DR: In this article, the authors focused on the recent progress in the preparation and electrochemical properties of the next-generation supercapacitors and showed that transition metal oxides (TMOs) could play a significant role in environmentally friendly, low-cost, and high-powered energy storage.
Abstract: With the increasing energy demand and the overconsumption of fossil fuels, renewable energy-storage devices with higher efficiency are of great interest. In particular, supercapacitors have recently gained significant attention due to their excellent charge–discharge performance, long-term cycle lifetimes, and high specific power. In addition, supercapacitors could also make up the difference in energy and power between batteries and traditional capacitors. In the future, the promising family of transition metal oxides (TMOs) will play a significant role in environmentally friendly, low-cost, and high-powered energy storage. Furthermore, one-dimensional (1D) and one-dimensional-analogue nanostructures could remarkably enhance the characteristic properties of TMOs. In this review, we focused on the recent progress in the preparation and electrochemical properties of the next-generation supercapacitors.
TL;DR: In this article, an effective strategy was developed to improve the conductivity of mixed-metal organic frameworks (M-MOFs) by partially substituting Ni2+ in the Ni-MOF with Co2+ or Zn2+.
Abstract: Metal–organic frameworks (MOFs) have obtained increasing attention as a kind of novel electrode material for energy storage devices. Yet low capacity in most MOFs largely thwarts their application. In this study, an effective strategy was developed to improve the conductivity of MOFs by partially substituting Ni2+ in the Ni-MOF with Co2+ or Zn2+. The mixed-metal organic frameworks (M-MOFs) showed excellent electrochemical performance, which is attributed not only to the favorable paths for charge transport due to the presence of free pores, but also to the raised electrochemical double-layer capacitance (EDLC) at the enlarged specific surface area of the material. Meanwhile, the cycling stability of the assembled hybrid supercapacitors (M-MOFs//CNTs–COOH) is enhanced due to the alleviation of phase transformation during electrochemical cycling tests. More interestingly, the Co/Ni-MOF//CNTs–COOH also exhibited an excellent energy density (49.5 W h kg−1) and power density (1450 W kg−1) simultaneously. These values demonstrated the better performance of all the MOF materials in supercapacitors at present. In addition to broadening the application of MOFs, our study may open a new avenue for bridging the performance gap between batteries and supercapacitors.
TL;DR: A general overview of synthetic MoS2 based nanocomposites via different preparation approaches and their applications in energy storage devices (Li‐ion battery, Na‐ion batteries, and supercapacitor) is presented.
Abstract: Typical layered transition-metal chalcogenide materials, in particular layered molybdenum disulfide (MoS2) nanocomposites, have attracted increasing attention in recent years due to their excellent chemical and physical properties in various research fieldsHere, a general overview of synthetic MoS2 based nanocomposites via different preparation approaches and their applications in energy storage devices (Li-ion battery, Na-ion battery, and supercapacitor) is presented. The relationship between morphologies and the electrochemical performances of MoS2-based nanocomposites in the three typical and promising rechargeable systems is also discussed. Finally, perspectives on major challenges and opportunities faced by MoS2-based materials to address the practical problems of MoS2-based materials are presented.
TL;DR: In this paper, the authors review and comment on recent progress in metal-organic framework-based lithium-ion batteries, sodium-ion battery, lithium-air battery, and supercapacitors.
TL;DR: It is shown that amorphous CP can be used as general synthesis precursors of highly complex mixed metal oxide shells and can be applied to produce ternary and quaternary metal oxide onions with tunable size and composition.
Abstract: Metal-organic frameworks (MOFs) or coordination polymers (CPs) have been used as precursors for synthesis of materials. Unlike crystalline MOF, amorphous CP is nonspecific to metal cation species, therefore its composition can be tuned easily. Here, it is shown that amorphous CP can be used as general synthesis precursors of highly complex mixed metal oxide shells. As a proof of concept, NiCo coordination polymer spheres are first synthesized and subsequently transformed into seven-layered NiCo oxide onions by rapid thermal oxidation. This approach is very versatile and can be applied to produce ternary and quaternary metal oxide onions with tunable size and composition. The NiCo oxide onions exhibit exceptional charge storage capability in aqueous electrolyte with high specific capacitance (≈1900 F g-1 at 2 A g-1 ), good rate capability, and ultrahigh cycling stability (93.6% retention over 20 000 cycles). A hybrid supercapacitor against graphene/multishelled mesoporous carbon sphere shows a high energy density of 52.6 Wh kg-1 at a power density of 1604 W kg-1 (based on active materials weight), as well as remarkable cycling stability.
TL;DR: The key factors influencing the performance of NPC electrodes to disclose related charge storage mechanisms are discussed and the trade‐off among N‐content, porous structure and electrical conductivity is involved as well as electrochemical behaviors in different electrolytes.
Abstract: Featured with unique mechanical, electronic and chemical properties, nitrogen-doped carbon materials have become the research hotspot of energy storage. As electrode materials in supercapacitors (SCs), N-doped carbons have demonstrated intriguing flexibility and superb performances in a wide electrochemical window, equipped with versatile properties as both cathodes and anodes for constructing high voltage devices. Compared with limited doping level, N-rich and porous carbon materials (NPCs) are of great desire to release the restricted properties of N species and obtain high specific capacitances (>600 F g−1), pushing the energy density towards the battery level without scarifying the capacitor-level power ability. In this Research News we firstly discuss the key factors influencing the performance of NPC electrodes to disclose related charge storage mechanisms. In addition, the trade-off among N-content, porous structure and electrical conductivity is involved as well as electrochemical behaviors in different electrolytes. Also, various progressive developments are highlighted systematically ranging from asymmetric to symmetric and hybrid configurations, covering both aqueous and non-aqueous systems. Finally, some stubborn and unsolved problems are summarized, with prospective research guidelines on NPC-based SCs.
TL;DR: In this paper, a hierarchical nanotube array (NTA) with a massive layered top and discretely separated nanotubes in a core-shell structure was grown on carbon fiber cloth (CFC) by template-assisted electrodeposition for high-performance supercapacitor application.
Abstract: A novel hierarchical nanotube array (NTA) with a massive layered top and discretely separated nanotubes in a core–shell structure, that is, nickel–cobalt metallic core and nickel–cobalt layered double hydroxide shell (NiCo@NiCo LDH), is grown on carbon fiber cloth (CFC) by template-assisted electrodeposition for high-performance supercapacitor application. The synthesized NiCo@NiCo LDH NTAs/CFC shows high capacitance of 2200 F g−1 at a current density of 5 A g−1, while 98.8% of its initial capacitance is retained after 5000 cycles. When the current density is increased from 1 to 20 A g−1, the capacitance loss is less than 20%, demonstrating excellent rate capability. A highly flexible all-solid-state battery-type supercapacitor is successfully fabricated with NiCo LDH NTAs/CFC as the positive electrode and electrospun carbon fibers/CFC as the negative electrode, showing a maximum specific capacitance of 319 F g−1, a high energy density of 100 W h kg−1 at 1.5 kW kg−1, and good cycling stability (98.6% after 3000 cycles). These fascinating electrochemical properties are resulted from the novel structure of electrode materials and synergistic contributions from the two electrodes, showing great potential for energy storage applications.
TL;DR: Low-cost materials are used including multiwall carbon nanotube, reduced graphene oxide, and metallic textiles to fabricate composite fabric electrodes, in which MWCNT and RGO are alternatively vacuum-filtrated directly onto Ni-coated cotton fabrics to achieve ultrahigh areal capacitance.
Abstract: High-performance supercapacitors (SCs) are promising energy storage devices to meet the pressing demand for future wearable applications. Because the surface area of a human body is limited to 2 m2 , the key challenge in this field is how to realize a high areal capacitance for SCs, while achieving rapid charging, good capacitive retention, flexibility, and waterproofing. To address this challenge, low-cost materials are used including multiwall carbon nanotube (MWCNT), reduced graphene oxide (RGO), and metallic textiles to fabricate composite fabric electrodes, in which MWCNT and RGO are alternatively vacuum-filtrated directly onto Ni-coated cotton fabrics. The composite fabric electrodes display typical electrical double layer capacitor behavior, and reach an ultrahigh areal capacitance up to 6.2 F cm-2 at a high areal current density of 20 mA cm-2 . All-solid-state fabric-type SC devices made with the composite fabric electrodes and water-repellent treatment can reach record-breaking performance of 2.7 F cm-2 at 20 mA cm-2 at the first charge-discharge cycle, 3.2 F cm-2 after 10 000 charge-discharge cycles, zero capacitive decay after 10 000 bending tests, and 10 h continuous underwater operation. The SC devices are easy to assemble into tandem structures and integrate into garments by simple sewing.
TL;DR: The evolved structure served as a robust Pt-free electrocatalyst with excellent activity for the oxygen reduction reaction (ORR) in an alkaline electrolyte solution and displayed exceptional capacitance and rate capability in a supercapacitor.
Abstract: Metal oxides and carbon-based materials are the most promising electrode materials for a wide range of low-cost and highly efficient energy storage and conversion devices. Creating unique nanostructures of metal oxides and carbon materials is imperative to the development of a new generation of electrodes with high energy and power density. Here we report our findings in the development of a novel graphene aerogel assisted method for preparation of metal oxide nanoparticles (NPs) derived from bulk MOFs (Co-based MOF, Co(mIM)2 (mIM = 2-methylimidazole). The presence of cobalt oxide (CoOx) hollow NPs with a uniform size of 35 nm monodispersed in N-doped graphene aerogels (NG-A) was confirmed by microscopic analyses. The evolved structure (denoted as CoOx/NG-A) served as a robust Pt-free electrocatalyst with excellent activity for the oxygen reduction reaction (ORR) in an alkaline electrolyte solution. In addition, when Co was removed, the resulting nitrogen-rich porous carbon–graphene composite electrode (d...
TL;DR: Recent advances in the synthesis of paper‐based electrodes, including paper‐supported electrodes and paper‐like electrodes are summarized and their structural features, electrochemical performances and implementation as electrodes for flexible energy storage devices including supercapacitors and batteries are highlighted and compared.
Abstract: Paper-based materials are emerging as a new category of advanced electrodes for flexible energy storage devices, including supercapacitors, Li-ion batteries, Li-S batteries, Li-oxygen batteries. This review summarizes recent advances in the synthesis of paper-based electrodes, including paper-supported electrodes and paper-like electrodes. Their structural features, electrochemical performances and implementation as electrodes for flexible energy storage devices including supercapacitors and batteries are highlighted and compared. Finally, we also discuss the challenges and opportunity of paper-based electrodes and energy storage devices.