Showing papers in "Nature Energy in 2017"

Silicon heterojunction solar cell with interdigitated back contacts for a photoconversion efficiency over 26

Abstract: The efficiency of silicon solar cells has a large influence on the cost of most photovoltaics panels. Here, researchers from Kaneka present a silicon heterojunction with interdigitated back contacts reaching an efficiency of 26.3% and provide a detailed loss analysis to guide further developments.

Defect passivation in hybrid perovskite solar cells using quaternary ammonium halide anions and cations

Abstract: The ionic defects at the surfaces and grain boundaries of organic–inorganic halide perovskite films are detrimental to both the efficiency and stability of perovskite solar cells. Here, we show that quaternary ammonium halides can effectively passivate ionic defects in several different types of hybrid perovskite with their negative- and positive-charged components. The efficient defect passivation reduces the charge trap density and elongates the carrier recombination lifetime, which is supported by density-function-theory calculation. The defect passivation reduces the open-circuit-voltage deficit of the p–i–n-structured device to 0.39 V, and boosts the efficiency to a certified value of 20.59 ± 0.45%. Moreover, the defect healing also significantly enhances the stability of films in ambient conditions. Our findings provide an avenue for defect passivation to further improve both the efficiency and stability of solar cells. Losses in solar cells can be caused by material defects in the bulk or at interfaces. Here, Zheng et al. use quaternary ammonium halides to passivate various perovskite absorbers and prepare solar cells with certified efficiency above 20%, suggesting that both anionic and cation defects are affected.

Enhanced electron extraction using SnO 2 for high-efficiency planar-structure HC(NH 2 ) 2 PbI 3 -based perovskite solar cells

Abstract: Planar structures for halide perovskite solar cells have recently garnered attention, due to their simple and low-temperature device fabrication processing. Unfortunately, planar structures typically show I–V hysteresis and lower stable device efficiency compared with mesoporous structures, especially for TiO2-based n-i-p devices. SnO2, which has a deeper conduction band and higher electron mobility compared with traditional TiO2, could enhance charge transfer from perovskite to electron transport layers, and reduce charge accumulation at the interface. Here we report low-temperature solution-processed SnO2 nanoparticles as an efficient electron transport layer for perovskite solar cells. Our SnO2-based devices are almost free of hysteresis, which we propose is due to the enhancement of electron extraction. By introducing a PbI2 passivation phase in the perovskite layer, we obtain a 19.9 ± 0.6% certified efficiency. The devices can be easily processed under low temperature (150 ∘C), offering an efficient method for the large-scale production of perovskite solar cells. Planar structured perovskite solar cells often show hysteresis and lower efficiency than mesoporous ones. Jiang et al. show that using a SnO2 electron transport layer improves the performance of planar devices, reporting a certified efficiency of 19.9%, and enables a lower processing temperature.

Ultra-high-rate pseudocapacitive energy storage in two-dimensional transition metal carbides

Abstract: Pseudocapacitors based on redox-active materials have relatively high energy density but suffer from low power capability. Here the authors report that two-dimensional transition metal carbides exhibit high gravimetric, volumetric and areal capacitance values at high char…

23.6%-efficient monolithic perovskite/silicon tandem solar cells with improved stability

Abstract: As the record single-junction efficiencies of perovskite solar cells now rival those of copper indium gallium selenide, cadmium telluride and multicrystalline silicon, they are becoming increasingly attractive for use in tandem solar cells due to their wide, tunable bandgap and solution processability. Previously, perovskite/silicon tandems were limited by significant parasitic absorption and poor environmental stability. Here, we improve the efficiency of monolithic, two-terminal, 1-cm2 perovskite/silicon tandems to 23.6% by combining an infrared-tuned silicon heterojunction bottom cell with the recently developed caesium formamidinium lead halide perovskite. This more-stable perovskite tolerates deposition of a tin oxide buffer layer via atomic layer deposition that prevents shunts, has negligible parasitic absorption, and allows for the sputter deposition of a transparent top electrode. Furthermore, the window layer doubles as a diffusion barrier, increasing the thermal and environmental stability to enable perovskite devices that withstand a 1,000-hour damp heat test at 85 ∘C and 85% relative humidity. Perovskite solar cells can complement silicon photovoltaics in multijunction devices. Here, the authors optimize light harvesting in monolithic perovskite-on-silicon devices and fabricate a certified 23.6% efficient, 1 cm2 tandem solar cell with a perovskite device that withstands damp heat tests.

Efficient ambient-air-stable solar cells with 2D–3D heterostructured butylammonium-caesium-formamidinium lead halide perovskites

Abstract: Perovskite solar cells are remarkably efficient; however, they are prone to degradation in water, oxygen and ultraviolet light. Cation engineering in 3D perovskite absorbers has led to reduced degradation. Alternatively, 2D Ruddlesden–Popper layered perovskites exhibit improved stability, but have not delivered efficient solar cells so far. Here, we introduce n-butylammonium cations into a mixed-cation lead mixed-halide FA0.83Cs0.17Pb(IyBr1−y)3 3D perovskite. We observe the formation of 2D perovskite platelets, interspersed between highly orientated 3D perovskite grains, which suppress non-radiative charge recombination. We investigate the relationship between thin-film composition, crystal alignment and device performance. Solar cells with an optimal butylammonium content exhibit average stabilized power conversion efficiency of 17.5 ± 1.3% with a 1.61-eV-bandgap perovskite and 15.8 ± 0.8% with a 1.72-eV-bandgap perovskite. The stability under simulated sunlight is also enhanced. Cells sustain 80% of their ‘post burn-in’ efficiency after 1,000 h in air, and close to 4,000 h when encapsulated. Various strategies are developed to combine high efficiency and stability in perovskite solar cells. Here, Wang et al. mix 2D and 3D mixed-cation and mixed-halide perovskite phases in solar cells with stabilized efficiencies up to 19.5% and improved stability under full illumination and ambient air.

Electrolyte additive enabled fast charging and stable cycling lithium metal batteries

Abstract: Batteries using lithium (Li) metal as anodes are considered promising energy storage systems because of their high energy densities. However, safety concerns associated with dendrite growth along with limited cycle life, especially at high charge current densities, hinder their practical uses. Here we report that an optimal amount (0.05 M) of LiPF6 as an additive in LiTFSI–LiBOB dual-salt/carbonate-solvent-based electrolytes significantly enhances the charging capability and cycling stability of Li metal batteries. In a Li metal battery using a 4-V Li-ion cathode at a moderately high loading of 1.75 mAh cm−2, a cyclability of 97.1% capacity retention after 500 cycles along with very limited increase in electrode overpotential is accomplished at a charge/discharge current density up to 1.75 mA cm−2. The fast charging and stable cycling performances are ascribed to the generation of a robust and conductive solid electrolyte interphase at the Li metal surface and stabilization of the Al cathode current collector. Deployment of rechargeable Li metal batteries requires fast charging capability and long-term cycling stability. Here the authors demonstrate the battery application potential of using a small amount of LiPF6 in a dual-salt electrolyte.

A facile surface chemistry route to a stabilized lithium metal anode

Abstract: Li dendrite formation is a major obstacle in the development of Li metal batteries. Nazar and colleagues present a protection method for the Li metal by an in situ synthesis of Li-based surface alloy composites, and demonstrate promising battery applications.

The future cost of electrical energy storage based on experience rates

Abstract: Electrical energy storage is expected to be important for decarbonizing personal transport and enabling highly renewable electricity systems. This study analyses data on 11 storage technologies, constructing experience curves to project future prices, and explores feasibl…

Enhancing ionic conductivity in composite polymer electrolytes with well-aligned ceramic nanowires

Abstract: In contrast to conventional organic liquid electrolytes that have leakage, flammability and chemical stability issues, solid electrolytes are widely considered as a promising candidate for the development of next-generation safe lithium-ion batteries. In solid polymer electrolytes that contain polymers and lithium salts, inorganic nanoparticles are often used as fillers to improve electrochemical performance, structure stability, and mechanical strength. However, such composite polymer electrolytes generally have low ionic conductivity. Here we report that a composite polymer electrolyte with well-aligned inorganic Li+-conductive nanowires exhibits an ionic conductivity of 6.05 × 10−5 S cm-1 at 30 ∘C, which is one order of magnitude higher than previous polymer electrolytes with randomly aligned nanowires. The large conductivity enhancement is ascribed to a fast ion-conducting pathway without crossing junctions on the surfaces of the aligned nanowires. Moreover, the long-term structural stability of the polymer electrolyte is also improved by the use of nanowires. Fast ionic conductivity of solid electrolytes is a must in the development of next-generation solid-electrolyte-based lithium-ion batteries. Here the authors report that composite polymer electrolytes with well-aligned inorganic nanowires can achieve much larger conductivities than those without.

Interfacial water reorganization as a pH-dependent descriptor of the hydrogen evolution rate on platinum electrodes

Abstract: Hydrogen evolution on platinum is a key reaction for electrocatalysis and sustainable energy storage, yet its pH-dependent kinetics are not fully understood. Here we present a detailed kinetic study of hydrogen adsorption and evolution on Pt(111) in a wide pH range. Electrochemical measurements show that hydrogen adsorption and hydrogen evolution are both slow in alkaline media, consistent with the observation of a shift in the rate-determining step for hydrogen evolution. Adding nickel to the Pt(111) surface lowers the barrier for hydrogen adsorption in alkaline solutions and thereby enhances the hydrogen evolution rate. We explain these observations with a model that highlights the role of the reorganization of interfacial water to accommodate charge transfer through the electric double layer, the energetics of which are controlled by how strongly water interacts with the interfacial field. The model is supported by laser-induced temperature-jump measurements. Our model sheds light on the origin of the slow kinetics for the hydrogen evolution reaction in alkaline media. Despite its role in electrocatalysis and hydrogen generation, a complete understanding of the hydrogen evolution reaction on platinum remains elusive. Here, a detailed kinetic study of hydrogen adsorption and evolution on Pt(111) highlights the role of interfacial water reorganization in the hydrogen adsorption step.

Two-dimensional heterostructures for energy storage

Abstract: Two-dimensional (2D) materials provide slit-shaped ion diffusion channels that enable fast movement of lithium and other ions. However, electronic conductivity, the number of intercalation sites, and stability during extended cycling are also crucial for building high-performance energy storage devices. While individual 2D materials, such as graphene, show some of the required properties, none of them can offer all properties needed to maximize energy density, power density, and cycle life. Here we argue that stacking different 2D materials into heterostructured architectures opens an opportunity to construct electrodes that would combine the advantages of the individual building blocks while eliminating the associated shortcomings. We discuss characteristics of common 2D materials and provide examples of 2D heterostructured electrodes that showed new phenomena leading to superior electrochemical performance. We also consider electrode fabrication approaches and finally outline future steps to create 2D heterostructured electrodes that could greatly expand current energy storage technologies. Heterostructures with alternating layers of different 2D materials are finding increasing attention in energy applications. Pomerantseva and Gogotsi survey the opportunities and challenges of both developing the heterostructures and their implementation in energy storage devices.

Energy storage deployment and innovation for the clean energy transition

Abstract: The clean energy transition requires a co-evolution of innovation, investment, and deployment strategies for emerging energy storage technologies. A deeply decarbonized energy system research platform needs materials science advances in battery technology to overcome the intermittency challenges of wind and solar electricity. Simultaneously, policies designed to build market growth and innovation in battery storage may complement cost reductions across a suite of clean energy technologies. Further integration of R&D and deployment of new storage technologies paves a clear route toward cost-effective low-carbon electricity. Here we analyse deployment and innovation using a two-factor model that integrates the value of investment in materials innovation and technology deployment over time from an empirical dataset covering battery storage technology. Complementary advances in battery storage are of utmost importance to decarbonization alongside improvements in renewable electricity sources. We find and chart a viable path to dispatchable US$1 W−1 solar with US$100 kWh−1 battery storage that enables combinations of solar, wind, and storage to compete directly with fossil-based electricity options. Electricity storage will benefit from both R&D and deployment policy. This study shows that a dedicated programme of R&D spending in emerging technologies should be developed in parallel to improve safety and reduce overall costs, and in order to maximize the general benefit for the system.

Low-bandgap mixed tin-lead iodide perovskite absorbers with long carrier lifetimes for all-perovskite tandem solar cells

Abstract: Tandem solar cells using only metal-halide perovskite sub-cells are an attractive choice for next-generation solar cells. However, the progress in developing efficient all-perovskite tandem solar cells has been hindered by the lack of high-performance low-bandgap perovskite solar cells. Here, we report efficient mixed tin–lead iodide low-bandgap (∼1.25 eV) perovskite solar cells with open-circuit voltages up to 0.85 V and over 70% external quantum efficiencies in the infrared wavelength range of 700–900 nm, delivering a short-circuit current density of over 29 mA cm−2 and demonstrating suitability for bottom-cell applications in all-perovskite tandem solar cells. Our low-bandgap perovskite solar cells achieve a maximum power conversion efficiency of 17.6% and a certified efficiency of 17.01% with a negligible current–voltage hysteresis. When mechanically stacked with a ∼1.58 eV bandgap perovskite top cell, our best all-perovskite 4-terminal tandem solar cell shows a steady-state efficiency of 21.0%. All-perovskite tandem solar cells hold the promise of high efficiencies whilst safeguarding the ease of fabrication intrinsic to perovskites. Here, Zhao et al. present a certified 17% efficient tin and lead perovskite solar cell, which is integrated as the low-bandgap component of a tandem device with 21% efficiency.

The underestimated potential of solar energy to mitigate climate change

Abstract: Despite being currently under-represented in IPCC reports, PV generation represents a growing share of power generation. This Perspective argues that underestimating PV potential led to suboptimal integration measures and that specific deployment strategies for emerging economies should be developed.

Strongly emissive perovskite nanocrystal inks for high-voltage solar cells

Abstract: Lead halide perovskite semiconductors have recently gained wide interest following their successful embodiment in solid-state photovoltaic devices with impressive power-conversion efficiencies, while offering a relatively simple and low-cost processability. Although the primary optoelectronic properties of these materials have already met the requirement for high-efficiency optoelectronic technologies, industrial scale-up requires more robust processing methods, as well as solvents that are less toxic than the ones that have been commonly used so successfully on the lab-scale. Here we report a fast, room-temperature synthesis of inks based on CsPbBr3 perovskite nanocrystals using short, low-boiling-point ligands and environmentally friendly solvents. Requiring no lengthy post-synthesis treatments, the inks are directly used to fabricate films of high optoelectronic quality, exhibiting photoluminescence quantum yields higher than 30% and an amplified spontaneous emission threshold as low as 1.5 μJ cm−2. Finally, we demonstrate the fabrication of perovskite nanocrystal-based solar cells, with open-circuit voltages as high as 1.5 V. Despite their impressive performance, more efforts are required to develop industrially scalable perovskite solar cells from less toxic solvents. Towards that aim, this study presents the use of colloidal nanoparticle inks for room-temperature fabrication of CsPbBr3 solar cells.

A flexible metal–organic framework with a high density of sulfonic acid sites for proton conduction

Abstract: The design of stable electrolyte materials with high proton conductivity for use in proton exchange membrane fuel cells remains a challenge. Most of the materials explored have good conductivity at high relative humidity (RH), but significantly decreased conductivity at reduced RH. Here we report a chemically stable and structurally flexible metal–organic framework (MOF), BUT-8(Cr)A, possessing a three-dimensional framework structure with one-dimensional channels, in which high-density sulfonic acid (–SO3H) sites arrange on channel surfaces for proton conduction. We propose that its flexible nature, together with its –SO3H sites, could allow BUT-8(Cr)A to self-adapt its framework under different humid environments to ensure smooth proton conduction pathways mediated by water molecules. Relative to other MOFs, BUT-8(Cr)A not only has a high proton conductivity of 1.27 × 10−1 S cm−1 at 100% RH and 80 °C but also maintains moderately high proton conductivity at a wide range of RH and temperature. Proton-conducting metal-organic frameworks (MOFs) could be used as the electrolytes in proton exchange membrane fuel cells but chemically stable materials that perform well at low humidity are still sought. Here the authors prepare a stable, structurally flexible MOF that maintains high proton conductivity under a wide range of humidity.

A materials perspective on Li-ion batteries at extreme temperatures

Abstract: Thermal effects on batteries, both due to external variations and internal fluctuations, significantly impact their performance. Ajayan and colleagues survey recent advances in understanding the thermal effects on individual battery components.

Perovskite ink with wide processing window for scalable high-efficiency solar cells

Abstract: Perovskite solar cells have made tremendous progress using laboratory-scale spin-coating methods in the past few years owing to advances in controls of perovskite film deposition. However, devices made via scalable methods are still lagging behind state-of-the-art spin-coated devices because of the complicated nature of perovskite crystallization from a precursor state. Here we demonstrate a chlorine-containing methylammonium lead iodide precursor formulation along with solvent tuning to enable a wide precursor-processing window (up to ∼8 min) and a rapid grain growth rate (as short as ∼1 min). Coupled with antisolvent extraction, this precursor ink delivers high-quality perovskite films with large-scale uniformity. The ink can be used by both spin-coating and blade-coating methods with indistinguishable film morphology and device performance. Using a blade-coated absorber, devices with 0.12-cm2 and 1.2-cm2 areas yield average efficiencies of 18.55% and 17.33%, respectively. We further demonstrate a 12.6-cm2 four-cell module (88% geometric fill factor) with 13.3% stabilized active-area efficiency output. Perovskite-based solar cells are often fabricated by methods that are not industrially scalable. Here, Yang et al. develop an ink formulation which gives similar devices by spin coating, the lab-scale standard, and blade coating, which is a more scalable, industry-relevant deposition method.

Intrinsic non-radiative voltage losses in fullerene-based organic solar cells

Abstract: The conversion efficiency of organic solar cells suffers from their low open-circuit voltages. Here, the authors expose a link between electron-vibrations coupling and non-radiative recombinations, derive a new limit for the efficiency of organic solar cells, and redefine their optimal optical gap.

Emergence of highly transparent photovoltaics for distributed applications

Abstract: Solar energy offers a viable solution to our growing energy need. While adoption of conventional photovoltaics on rooftops and in solar farms has grown rapidly in the last decade, there is still plenty of opportunity for expansion. See-through solar technologies with partial light transmission developed over the past 30 years have initiated methods of integration not possible with conventional modules. The large-scale deployment necessary to offset global energy consumption could be further accelerated by developing fully invisible solar cells that selectively absorb ultraviolet and near-infrared light, allowing many of the surfaces of our built environment to be turned into solar harvesting arrays without impacting the function or aesthetics. Here, we review recent advances in photovoltaics with varying degrees of visible light transparency. We discuss the figures of merit necessary to characterize transparent photovoltaics, and outline the requirements to enable their widespread adoption in buildings, windows, electronic device displays, and automobiles. Transparency offers integration routes unavailable to opaque photovoltaics. Here, Lunt and co-workers review recent progress in transparent solar technologies, highlight technical challenges and measurement considerations, and review performance requirements for various applications.

Accelerated degradation of methylammonium lead iodide perovskites induced by exposure to iodine vapour

Abstract: Efficiencies of organic–inorganic lead halide perovskite solar cells (PSCs) have significantly increased in recent years, but instability issues impede their further development and application. Previous studies reported that volatile species (for example, iodine, I2) were generated when perovskites were subjected to moisture, oxygen, light illumination, applied electric field, and thermal stress (all of which are relevant to the operation of PSCs in practical applications). Here we show that I2 vapour causes severe degradation of MAPbI3 (MA: CH3NH3+) perovskite, due to chemical chain reactions. Furthermore, I2 vapour could also induce degradation of other iodide-based perovskites, such as FAPbI3 (FA: HC(NH2)2+) and FA0.8Cs0.2PbI3. The results reveal a universal degradation factor for iodide-based perovskite by I2. As the release of I2 is nearly inevitable during practical applications, this work suggests that MAPbI3 may not be suitable for long-term stable solar cells and it is imperative to develop other types of perovskite material to achieve stable PSCs. Extensive efforts are under way to tackle the degradation issue—one of the biggest challenges for the practical application of perovskite-based solar cells. Here the authors show that CH3NH3PbI3 and several other iodine-containing perovskites are inherently unstable due to decomposition caused by self-generated I2.

Raising the one-sun conversion efficiency of III-V/Si solar cells to 32.8% for two junctions and 35.9% for three junctions

Abstract: To improve the efficiency of photovoltaic devices while keeping the same spatial footprint, solar cells can be stacked on top of each other. Here, Essig et al. fabricate very efficient dual-junction and triple-junction solar cells by placing one or two III–V solar cells on top of a silicon solar cell.

Stable 6%-efficient Sb 2 Se 3 solar cells with a ZnO buffer layer

Abstract: Sb2Se3, a binary compound containing non-toxic and Earth-abundant constituents, is a promising absorber material for low-cost, high-efficiency photovoltaics. Current Sb2Se3 thin-film solar cells use toxic CdS as the buffer layer and suffer from unsatisfactory stability. Here we selected ZnO as the buffer layer and constructed superstrate Sb2Se3 solar cells with a certified power conversion efficiency of 5.93%. Randomly oriented ZnO produced by spray pyrolysis induced the growth of Sb2Se3 with preferred [221] orientation, and hence resulted in devices with fewer interfacial defects and better efficiency. Moreover, our unencapsulated device survived the stringent damp-heat (85 ∘C, 85% humidity, 1,100 h), light-soaking (50 ∘C, 1.3 sun, 1,100 h), thermal cycling, and ultraviolet preconditioning tests. The combined features of stability, Earth-abundant constituent and potentially low-cost manufacturing highlight the great potential of Sb2Se3 solar cell as a possible non-toxic alternative to CdTe photovoltaics. Thin-film photovoltaic devices are often based on toxic or rare materials. Here, Wang et al. grow oriented Sb2Se3 thin film on a ZnO buffer layer, and fabricate solar cells with a certified 5.9% conversion efficiency and which pass harsh stability tests under humidity, heat and illumination.

Large guanidinium cation mixed with methylammonium in lead iodide perovskites for 19% efficient solar cells

Abstract: Organic–inorganic lead halide perovskites have shown photovoltaic performances above 20% in a range of solar cell architectures while offering simple and low-cost processability. Despite the multiple ionic compositions that have been reported so far, the presence of organic constituents is an essential element in all of the high-efficiency formulations, with the methylammonium and formamidinium cations being the sole efficient options available to date. In this study, we demonstrate improved material stability after the incorporation of a large organic cation, guanidinium, into the MAPbI3 crystal structure, which delivers average power conversion efficiencies over 19%, and stabilized performance for 1,000 h under continuous light illumination, a fundamental step within the perovskite field.

Reversible multi-electron redox chemistry of π-conjugated N-containing heteroaromatic molecule-based organic cathodes

Abstract: Even though organic molecules with well-designed functional groups can be programmed to have high electron density per unit mass, their poor electrical conductivity and low cycle stability limit their applications in batteries. Here we report a facile synthesis of π-conjugated quinoxaline-based heteroaromatic molecules (3Q) by condensation of cyclic carbonyl molecules with o-phenylenediamine. 3Q features a number of electron-deficient pyrazine sites, where multiple redox reactions take place. When hybridized with graphene and coupled with an ether-based electrolyte, an organic cathode based on 3Q molecules displays a discharge capacity of 395 mAh g−1 at 400 mA g−1 (1C) in the voltage range of 1.2–3.9 V and a nearly 70% capacity retention after 10,000 cycles at 8 A g−1. It also exhibits a capacity of 222 mAh g−1 at 20C, which corresponds to 60% of the initial specific capacity. Our results offer evidence that heteroaromatic molecules with multiple redox sites are promising in developing high-energy-density, long-cycle-life organic rechargeable batteries. Organic compounds can be used as electrode materials for Li-ion batteries, but problems such as facile dissolution and low electrical conductivity hinder their application. Here the authors report π-conjugated quinoxaline-based heteroaromatic molecules with multiple redox sites to tackle the problems.

Activation of surface oxygen sites on an iridium-based model catalyst for the oxygen evolution reaction

Abstract: The oxygen evolution reaction (OER) is of prime importance in multiple energy storage devices; however, deeper mechanistic understanding is required to design enhanced electrocatalysts for the reaction. Current understanding of the OER mechanism based on oxygen adsorption on a metallic surface site fails to fully explain the activity of iridium and ruthenium oxide surfaces, and the drastic surface reconstruction observed for the most active OER catalysts. Here we demonstrate, using La2LiIrO6 as a model catalyst, that the exceptionally high activity found for Ir-based catalysts arises from the formation of active surface oxygen atoms that act as electrophilic centres for water to react. Moreover, with the help of transmission electron microscopy, we observe drastic surface reconstruction and iridium migration from the bulk to the surface. Therefore, we establish a correlation between surface activity and surface stability for OER catalysts that is rooted in the formation of surface reactive oxygen.

Solar conversion of CO2 to CO using Earth-abundant electrocatalysts prepared by atomic layer modification of CuO

Abstract: The solar-driven electrochemical reduction of CO2 to fuels and chemicals provides a promising way for closing the anthropogenic carbon cycle. However, the lack of selective and Earth-abundant catalysts able to achieve the desired transformation reactions in an aqueous matrix presents a substantial impediment as of today. Here we introduce atomic layer deposition of SnO2 on CuO nanowires as a means for changing the wide product distribution of CuO-derived CO2 reduction electrocatalysts to yield predominantly CO. The activity of this catalyst towards oxygen evolution enables us to use it both as the cathode and anode for complete CO2 electrolysis. In the resulting device, the electrodes are separated by a bipolar membrane, allowing each half-reaction to run in its optimal electrolyte environment. Using a GaInP/GaInAs/Ge photovoltaic we achieve the solar-driven splitting of CO2 into CO and oxygen with a bifunctional, sustainable and all Earth-abundant system at an efficiency of 13.4%. Electrochemical reduction of CO2 to CO is a route to synthesize fuels, but cheaper and more selective catalysts are required. Using a cell equipped with a bipolar membrane and the same Earth-abundant electrocatalyst at each electrode, Schreier et al. selectively produce CO, powered by a triple-junction photovoltaic.

Solar-driven reforming of lignocellulose to H 2 with a CdS/CdO x photocatalyst

Abstract: This work was supported by the Christian Doppler Research Association (Austrian Federal Ministry of Science, Research and Economy and the National Foundation for Research, Technology and Development), the OMV Group (to E.R.), the EPSRC (DTA studentships for D.W.W. and T.E.R), the Isaac Newton Trust, the German Research Foundation (to M.F.K.), the World Premier Institute Research Center Initiative (WPI), MEXT, Japan (to K.L.O.) and a Marie Curie Research fellowship (to K.H.L., GAN 701192 - VSHER).

Enhanced selectivity in mixed matrix membranes for CO2 capture through efficient dispersion of amine-functionalized MOF nanoparticles

Abstract: Mixed matrix membranes (MMMs) for gas separation applications have enhanced selectivity when compared with the pure polymer matrix, but are commonly reported with low intrinsic permeability, which has major cost implications for implementation of membrane technologies in large-scale carbon capture projects. High-permeability polymers rarely generate sufficient selectivity for energy-efficient CO2 capture. Here we report substantial selectivity enhancements within high-permeability polymers as a result of the efficient dispersion of amine-functionalized, nanosized metal–organic framework (MOF) additives. The enhancement effects under optimal mixing conditions occur with minimal loss in overall permeability. Nanosizing of the MOF enhances its dispersion within the polymer matrix to minimize non-selective microvoid formation around the particles. Amination of such MOFs increases their interaction with thepolymer matrix, resulting in a measured rigidification and enhanced selectivity of the overall composite. The optimal MOF MMM performance was verified in three different polymer systems, and also over pressure and temperature ranges suitable for carbon capture. Mixed matrix membranes can separate CO2 from flue gas mixtures but increasing selectivity without sacrificing permeability remains challenging. Selectivity can be increased with little loss in permeability by using nanoparticulate, amine-functionalized metal–organic framework fillers.