Journal ArticleDOI
Progress in research on hybrid metal matrix composites
Miao Zhou,Miao Zhou,Miao Zhou,Lingbao Ren,Leqing Fan,Leqing Fan,Zhang Yaran,Zhang Yaran,T.H. Lu,T.H. Lu,Gaofeng Quan,Gaofeng Quan,Manoj Gupta +12 more
TLDR
In this paper, a review of the recent developments in the fabrication techniques and properties characterization of Al, Mg, Ti, Cu, Fe/steel and Ni matrix composites containing hybrid reinforcements is presented.About:
This article is published in Journal of Alloys and Compounds.The article was published on 2020-10-15. It has received 94 citations till now.read more
Citations
More filters
Journal ArticleDOI
Enhanced mechanical properties of 6082 aluminum alloy via SiC addition combined with squeeze casting
TL;DR: In this article, the SiCp/Al 6082 composites were prepared by the addition of the micron-sized SiC particles combined with the squeeze casting, which had a significant impact on the microstructure and mechanical properties of the 6082 aluminum alloy.
Journal ArticleDOI
A review on wear-resistant coating with high hardness and high toughness on the surface of titanium alloy
TL;DR: Wang et al. as mentioned in this paper reviewed the typical wear-resistant coatings with high hardness and high toughness on the surface of titanium alloy from the aspects of preparation process, microstructure, mechanical properties, and strengthening-toughening mechanisms, such as gradient structure coating, multi-scale structure coating and layered structure coating.
Journal ArticleDOI
Influence of B4C and industrial waste fly ash reinforcement particles on the micro structural characteristics and mechanical behavior of aluminium (Al–Mg–Si-T6) hybrid metal matrix composite
M. Saravana Kumar,M. Vasumathi,S. Rashia Begum,Scutaru Maria Luminita,Sorin Vlase,Catalin I. Pruncu +5 more
TL;DR: In this article, a hybrid composite of high strength and low density for automotive application to suit the above needs is presented, and the results show that the composite with 10% fly ash shows enhanced at maximum the properties when compared to others.
Journal ArticleDOI
Investigation of the Effects of Cooling and Lubricating Strategies on Tribological Characteristics in Machining of Hybrid Composites
TL;DR: In this paper , the machinability of B-Ti-SiCP reinforced hybrid composites is investigated under different milling conditions, such as dry, minimum quantity lubrication (MQL)-assisted and cryogenic LN2-assisted.
Journal ArticleDOI
Bioinspired multiscale Al2O3-rGO/Al laminated composites with superior mechanical properties
TL;DR: In this article, a multiscale Al2O3-rGO/Al laminated composite via flake powder metallurgy is presented, which has the synergistic strengthening effect of 1 + ǫ+ǫ 1>2.
References
More filters
Journal ArticleDOI
Additive manufacturing of metallic components – Process, structure and properties
Tarasankar Debroy,Huiliang Wei,J.S. Zuback,T. Mukherjee,John W. Elmer,John O. Milewski,Allison M. Beese,Alexander E. Wilson-Heid,Amitava De,Wei Zhang +9 more
TL;DR: A review of the emerging research on additive manufacturing of metallic materials is provided in this article, which provides a comprehensive overview of the physical processes and the underlying science of metallurgical structure and properties of the deposited parts.
Journal ArticleDOI
Bioinspired structural materials
TL;DR: The common design motifs of a range of natural structural materials are reviewed, and the difficulties associated with the design and fabrication of synthetic structures that mimic the structural and mechanical characteristics of their natural counterparts are discussed.
Journal ArticleDOI
Approaching ballistic transport in suspended graphene.
TL;DR: This work shows that the fluctuations are significantly reduced in suspended graphene samples and reports low-temperature mobility approaching 200,000 cm2 V-1 s-1 for carrier densities below 5 x 109 cm-2, which cannot be attained in semiconductors or non-suspended graphene.
Journal ArticleDOI
Additive manufacturing of metals
TL;DR: In this paper, the authors describe the complex relationship between additive manufacturing processes, microstructure and resulting properties for metals, and typical microstructures for additively manufactured steel, aluminium and titanium are presented.
Journal ArticleDOI
Biological materials: Structure and mechanical properties
TL;DR: In this article, the basic building blocks are described, starting with the 20 amino acids and proceeding to polypeptides, polysaccharides, and polyprotein-saccharide.