Showing papers on "Fiber published in 2015"

A Review on Natural Fiber Reinforced Polymer Composite and Its Applications

Abstract: Natural fibers are getting attention from researchers and academician to utilize in polymer composites due to their ecofriendly nature and sustainability. The aim of this review article is to provide a comprehensive review of the foremost appropriate as well as widely used natural fiber reinforced polymer composites (NFPCs) and their applications. In addition, it presents summary of various surface treatments applied to natural fibers and their effect on NFPCs properties. The properties of NFPCs vary with fiber type and fiber source as well as fiber structure. The effects of various chemical treatments on the mechanical and thermal properties of natural fibers reinforcements thermosetting and thermoplastics composites were studied. A number of drawbacks of NFPCs like higher water absorption, inferior fire resistance, and lower mechanical properties limited its applications. Impacts of chemical treatment on the water absorption, tribology, viscoelastic behavior, relaxation behavior, energy absorption flames retardancy, and biodegradability properties of NFPCs were also highlighted. The applications of NFPCs in automobile and construction industry and other applications are demonstrated. It concluded that chemical treatment of the natural fiber improved adhesion between the fiber surface and the polymer matrix which ultimately enhanced physicomechanical and thermochemical properties of the NFPCs.

Conductive Fiber‐Based Ultrasensitive Textile Pressure Sensor for Wearable Electronics

Abstract: A flexible and sensitive textile-based pressure sensor is developed using highly conductive fibers coated with dielectric rubber materials. The pressure sensor exhibits superior sensitivity, very fast response time, and high stability, compared with previous textile-based pressure sensors. By using a weaving method, the pressure sensor can be applied to make smart gloves and clothes that can control machines wirelessly as human-machine interfaces.

Extremely Elastic Wearable Carbon Nanotube Fiber Strain Sensor for Monitoring of Human Motion.

Abstract: The increasing demand for wearable electronic devices has made the development of highly elastic strain sensors that can monitor various physical parameters an essential factor for realizing next generation electronics. Here, we report an ultrahigh stretchable and wearable device fabricated from dry-spun carbon nanotube (CNT) fibers. Stretching the highly oriented CNT fibers grown on a flexible substrate (Ecoflex) induces a constant decrease in the conductive pathways and contact areas between nanotubes depending on the stretching distance; this enables CNT fibers to behave as highly sensitive strain sensors. Owing to its unique structure and mechanism, this device can be stretched by over 900% while retaining high sensitivity, responsiveness, and durability. Furthermore, the device with biaxially oriented CNT fiber arrays shows independent cross-sensitivity, which facilitates simultaneous measurement of strains along multiple axes. We demonstrated potential applications of the proposed device, such as st...

Highly thermally conductive and mechanically strong graphene fibers

Abstract: Graphene, a single layer of carbon atoms bonded in a hexagonal lattice, is the thinnest, strongest, and stiffest known material and an excellent conductor of heat and electricity. However, these superior properties have yet to be realized for graphene-derived macroscopic structures such as graphene fibers. We report the fabrication of graphene fibers with high thermal and electrical conductivity and enhanced mechanical strength. The inner fiber structure consists of large-sized graphene sheets forming a highly ordered arrangement intercalated with small-sized graphene sheets filling the space and microvoids. The graphene fibers exhibit a submicrometer crystallite domain size through high-temperature treatment, achieving an enhanced thermal conductivity up to 1290 watts per meter per kelvin. The tensile strength of the graphene fiber reaches 1080 megapascals.

A Review of Natural Fibers Used in Biocomposites: Plant, Animal and Regenerated Cellulose Fibers

Abstract: Natural fibers today are a popular choice for applications in composite manufacturing. Based on the sustainability benefits, biofibers such as plant fibers are replacing synthetic fibers in composites. These fibers are used to manufacture several biocomposites. The chemical composition and properties of each of the fibers changes, which demands the detailed comparison of these fibers. The reinforcement potential of natural fibers and their properties have been described in numerous papers. Today, high performance biocomposites are produced from several years of research. Plant fibers, particularly bast and leaf, find applications in automotive industries. While most of the other fibers are explored in lab scales they have not yet found large-scale commercial applications. It is necessary to also consider other fibers such as ones made from seed (coir) and animals (chicken feather) as they are secondary or made from waste products. Few plant fibers such as bast fibers are often reviewed briefly but other p...

Hierarchically buckled sheath-core fibers for superelastic electronics, sensors, and muscles

Abstract: Superelastic conducting fibers with improved properties and functionalities are needed for diverse applications. Here we report the fabrication of highly stretchable (up to 1320%) sheath-core conducting fibers created by wrapping carbon nanotube sheets oriented in the fiber direction on stretched rubber fiber cores. The resulting structure exhibited distinct short- and long-period sheath buckling that occurred reversibly out of phase in the axial and belt directions, enabling a resistance change of less than 5% for a 1000% stretch. By including other rubber and carbon nanotube sheath layers, we demonstrated strain sensors generating an 860% capacitance change and electrically powered torsional muscles operating reversibly by a coupled tension-to-torsion actuation mechanism. Using theory, we quantitatively explain the complementary effects of an increase in muscle length and a large positive Poisson’s ratio on torsional actuation and electronic properties.

Hybrid fibers made of molybdenum disulfide, reduced graphene oxide, and multi-walled carbon nanotubes for solid-state, flexible, asymmetric supercapacitors.

Abstract: One of challenges existing in fiber-based supercapacitors is how to achieve high energy density without compromising their rate stability. Owing to their unique physical, electronic, and electrochemical properties, two-dimensional (2D) nanomaterials, e.g., molybdenum disulfide (MoS2) and graphene, have attracted increasing research interest and been utilized as electrode materials in energy-related applications. Herein, by incorporating MoS2 and reduced graphene oxide (rGO) nanosheets into a well-aligned multi-walled carbon nanotube (MWCNT) sheet followed by twisting, MoS2-rGO/MWCNT and rGO/MWCNT fibers are fabricated, which can be used as the anode and cathode, respectively, for solid-state, flexible, asymmetric supercapacitors. This fiber-based asymmetric supercapacitor can operate in a wide potential window of 1.4 V with high Coulombic efficiency, good rate and cycling stability, and improved energy density.

Effects of fiber orientation and anisotropy on tensile strength and elastic modulus of short fiber reinforced polymer composites

Abstract: An experimental study was conducted to investigate anisotropy effects on tensile properties of two short glass fiber reinforced thermoplastics. Tensile tests were performed in various mold flow directions and with two thicknesses. A shell–core morphology resulting from orientation distribution of fibers influenced the degree of anisotropy. Tensile strength and elastic modulus nonlinearly decreased with specimen angle and Tsai–Hill criterion was found to correlate variation of these properties with the fiber orientation. Variation of tensile toughness with fiber orientation and strain rate was evaluated and mechanisms of failure were identified based on fracture surface microscopic analysis and crack propagation paths. Fiber length, diameter, and orientation distribution mathematical models were also used along with analytical approaches to predict tensile strength and elastic modulus form tensile properties of constituent materials. Laminate analogy and modified Tsai–Hill criteria provided satisfactory predictions of elastic modulus and tensile strength, respectively.

Synthesis of β-Cyclodextrin-Based Electrospun Nanofiber Membranes for Highly Efficient Adsorption and Separation of Methylene Blue

Abstract: Water-insoluble β-cyclodextrin-based fibers were synthesized by electrospinining followed by thermal cross-linking. The fibers were characterized by field-emission scanning electron microscopic (FE-SEM) and Fourier transformed infrared spectrometer (FT-IR). The highly insoluble fraction obtained from different pH values (3-11) indicates successful cross-linking reactions and their usability in aqueous solution. After the cross-linking reaction, the fibers' tensile strength increases significantly and the BET surface area is 19.49 m(2)/g. The cross-linked fibers exhibited high adsorption capacity for cationic dye methylene blue (MB) with good recyclability. The adsorption performance can be fitted well with pseudo-second-order model and Langmuir isotherm model. The maximum adsorption capacity is 826.45 mg/g according to Langmuir fitting. Due to electrostatic repulsion, the fibers show weak adsorption toward negatively charged anionic dye methyl orange (MO). On the basis of the selective adsorption, the fiber membrane can separate the MB/MO mixture solution by dynamic filtration at a high flow rate of 150 mL/min. The fibers can maintain good fibrous morphology and high separation efficiency even after five filtration-regeneration cycles. The obtained results suggested potential applications of β-cyclodextrin-based electrospun fibers in the dye wastewater treatment field.

3D Si/C Fiber Paper Electrodes Fabricated Using a Combined Electrospray/Electrospinning Technique for Li-Ion Batteries

Abstract: Although the theoretical capacity of silicon is ten times higher than that of graphite, the overall electrode capacity of Si anodes is still low due to the low Si loading and heavy metal current collector. Here, a novel flexible 3D Si/C fiber paper electrode synthesized by simultaneously electrospraying nano-Si-PAN (polyacrylonitrile) clusters and electrospinning PAN fibers followed by carbonization is reported. The combined technology allows uniform incorporation of Si nanoparticles into a carbon textile matrix to form a nano-Si/carbon composite fiber paper. The flexible 3D Si/C fiber paper electrode demonstrate a very high overall capacity of ≈1600 mAh g-1 with capacity loss less than 0.079% per cycle for 600 cycles and excellent rate capability. The exceptional performance is attributed to the unique architecture of the flexible 3D Si/C fiber paper, i.e., the resilient and conductive carbon fiber network matrix, carbon-coated Si nanoparticle clusters, strong adhesion between carbon fibers and Si nanoparticle clusters, and uniform distribution of Si/C clusters in the carbon fiber frame. The scalable and facile synthesis method, good mechanical properties, and excellent electrochemical performance at a high Si loading make the flexible 3D Si/C fiber paper batteries extremely attractive for plug-in electric vehicles, flexible electronics, space exploration, and military applications.

Hierarchically structured MnO2/graphene/carbon fiber and porous graphene hydrogel wrapped copper wire for fiber-based flexible all-solid-state asymmetric supercapacitors

Abstract: Recent progress in fiber-based supercapacitors has attracted tremendous attention due to the tiny volume, high flexibility and weavability of the fibers, which are required for the development of high-performance fiber electrodes. In this work, we report for the first time, the design and fabrication of two types of core–shell fiber-based electrodes, i.e. hierarchically structured manganese dioxide (MnO2)/graphene/carbon fiber (CF) and three-dimensional (3D) porous graphene hydrogel (GH) wrapped copper wire (CW), and their practical application in a fiber-architectured flexible all-solid-state supercapacitor. Taking advantage of the synergistic effects of the different components in the hierarchically structured nanohybrid fiber electrodes and the merits of the proposed synthesis strategies, the assembled asymmetric supercapacitor device using MnO2/graphene/CF as the positive electrode and GH/CW as the negative electrode could be cycled reversibly in a high-voltage region of 0–1.6 V, delivering a high areal energy density of 18.1 μW h cm−2 and volumetric energy density of 0.9 mW h cm−3. Furthermore, our fiber-based flexible supercapacitor also shows a good rate capability, excellent flexibility and high long term cyclability, which makes it a promising power source for flexible energy-related devices.

Stretchable, weavable coiled carbon nanotube/MnO2/polymer fiber solid-state supercapacitors.

Abstract: Stretchable, Weavable Coiled Carbon Nanotube/MnO 2 /Polymer Fiber Solid-State Supercapacitors

Effect of Experimental Parameters on Morphological, Mechanical and Hydrophobic Properties of Electrospun Polystyrene Fibers

Abstract: Polystyrene (PS) dissolved in a mixture of N, N-dimethylformamide (DMF) and/or tetrahydrofuran (THF) was electrospun to prepare fibers with sub-micron diameters. The effects of electrospinning parameters, including solvent combinations, polymer concentrations, applied voltage on fiber morphology, as well as tensile and hydrophobic properties of the fiber mats were investigated. Scanning electron microscope (SEM) images of electrospun fibers (23% w/v PS solution with applied voltage of 15 kV) showed that a new type of fiber with double-strand morphology was formed when the mass ratio of DMF and THF was 50/50 and 25/75. The tensile strength of the PS fiber film was 1.5 MPa, indicating strong reinforcement from double-strand fibers. Bead-free fibers were obtained by electrospinning 40% (w/v) PS/DMF solution at an applied voltage of 15 kV. Notably, when the ratio of DMF and THF was 100/0, the maximum contact angle (CA) value of the electrospun PS films produced at 15 kV was 148°.

Nanomaterials for Functional Textiles and Fibers

Abstract: Nanoparticles are very interesting because of their surface properties, different from bulk materials. Such properties make possible to endow ordinary products with new functionalities. Their relatively low cost with respect to other nano-additives make them a promising choice for industrial mass-production systems. Nanoparticles of different kind of materials such as silver, titania, and zinc oxide have been used in the functionalization of fibers and fabrics achieving significantly improved products with new macroscopic properties. This article reviews the most relevant approaches for incorporating such nanoparticles into synthetic fibers used traditionally in the textile industry allowing to give a solution to traditional problems for textiles such as the microorganism growth onto fibers, flammability, robustness against ultraviolet radiation, and many others. In addition, the incorporation of such nanoparticles into special ultrathin fibers is also analyzed. In this field, electrospinning is a very promising technique that allows the fabrication of ultrathin fiber mats with an extraordinary control of their structure and properties, being an ideal alternative for applications such as wound healing or even functional membranes.

Smart Fiber Membrane for pH-Induced Oil/Water Separation.

Abstract: Wastewater contaminated with oil or organic compounds poses threats to the environment and humans. Efficient separation of oil and water are highly desired yet still challenging. This paper reports the fabrication of a smart fiber membrane by depositing pH-responsive copolymer fibers on a stainless steel mesh through electrospinning. The cost-effective precursor material poly(methyl methacrylate)-block-poly(4-vinylpyridine) (PMMA-b-P4VP) was synthesized using copper(0)-mediated reversible-deactivation radical polymerization. The pH-responsive P4VP and the underwater oleophilic/hydrophilic PMMA confer the as-prepared membrane with switchable surface wettability toward water and oil. The three-dimensional network structure of the fibers considerably strengthens the oil/water wetting property of the membrane, which is highly desirable in the separation of oil and water mixtures. The as-prepared fiber membrane accomplishes gravity-driven pH-controllable oil/water separations. Oil selectively passes through the membrane, whereas water remains at the initial state; after the membrane is wetted with acidic water (pH 3), a reverse separation is realized. Both separations are highly efficient, and the membrane also exhibits switchable wettability after numerous cycles of the separation process. This cost-effective and easily mass-produced smart fiber membrane with excellent oil-fouling repellency has significant potential in practical applications, such as water purification and oil recovery.

Transforming Pristine Carbon Fiber Tows into High Performance Solid-State Fiber Supercapacitors.

Abstract: A facile activation strategy can transform pristine carbon fiber tows into high-performance fiber electrodes with a specific capacitance of 14.2 F cm(-3) . The knottable fiber supercapacitor shows an energy density of 0.35 mW h cm(-3) , an ultrahigh power density of 3000 mW cm(-3) , and a remarkable capacitance retention of 68%, when the scan rate increases from 10 to 1000 mV s(-1) .

Demonstration of a memory for tightly guided light in an optical nanofiber.

Abstract: Light signals propagating down an ultrathin fiber can be temporarily stored in a cloud of cold atoms surrounding the fiber.

Graphene-based single fiber supercapacitor with a coaxial structure

Abstract: A novel all graphene coaxial fiber supercapacitor (GCS) was fabricated, consisting of a continuously wet-spun core graphene fiber and facilely dip-coated graphene sheath. GCS is flexible, lightweight and strong, and is also accompanied by a high specific capacitance of 205 mF cm−2 (182 F g−1) and high energy density of 17.5 μW h cm−2 (15.5 W h kg−1). The energy density was further improved to 104 μW h cm−2, when an organic ion liquid electrolyte was used.