University of Mons

About: University of Mons is a education organization based out in Mons, Belgium. It is known for research contribution in the topics: Large Hadron Collider & Standard Model. The organization has 3073 authors who have published 9465 publications receiving 294776 citations.

Designing polylactide/clay nanocomposites for textile applications: Effect of processing conditions, spinning, and characterization

Abstract: An experimental study was carried out to design polylactide (PLA)-clay nanocomposites for developing fibers. PLA and 1–10 wt % of a selected organomodified bentonite (Bentone® 104-B104) were melt mixed to examine the effect of processing conditions (temperature, shear, residence time) on the morphology of performed polymer nanocomposites (PNC). Because of a good compatibility with PLA matrix, the dispersion of B104 occurred under different conditions without difficulty, and a similar morphology was obtained. The results obtained showed that at low temperature of mixing, the shear stress exerted on polymer has a key role on the extent of intercalation and delamination. Upscale experiments were further performed using optimized conditions and 4 wt % B104 was added to PLA matrix by melt blending to produce PNC for spinning. Then, the recovered PNC were melt spun to produce multifilaments yarns, and it was demonstrated that surprisingly, it is not necessary to use a plasticizer to spin a blend with 4 wt % B104. The properties of the yarns have been studied in terms of clay dispersion as well as thermal, mechanical, and shrinkage properties. B104 could be added up to 4 wt % into PLA without detrimentally sacrificing the tensile strength of melt-spun filaments, especially at high draw ratio. Interestingly, the PNC-based multifilaments were knitted and the flammability studied using cone calorimeter at 35 kW/m2. A strong decrease, up to 46%, of the heat release rate was measured. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008

Searches for time-dependent neutrino sources with icecube data from 2008 to 2012

Abstract: In this paper searches for flaring astrophysical neutrino sources and sources with periodic emission with the IceCube neutrino telescope are presented. In contrast to time-integrated searches, where steady emission is assumed, the analyses presented here look for a time-dependent signal of neutrinos using the information from the neutrino arrival times to enhance the discovery potential. A search was performed for correlations between neutrino arrival times and directions, as well as neutrino emission following time-dependent light curves, sporadic emission, or periodicities of candidate sources. These include active galactic nuclei, soft gamma-ray repeaters, supernova remnants hosting pulsars, microquasars, and X-ray binaries. The work presented here updates and extends previously published results to a longer period that covers 4 years. of data from 2008 April 5 to 2012 May 16, including the first year of operation of the completed 86 string detector. The analyses did not find any significant time-dependent point sources of neutrinos, and the results were used to set upper limits on the neutrino flux from source candidates.

Measurement of the inclusive 3-jet production differential cross section in proton–proton collisions at 7 TeV and determination of the strong coupling constant in the TeV range

Abstract: This paper presents a measurement of the inclusive 3-jet production differential cross section at a proton-proton centre-of-mass energy of 7 TeV using data corresponding to an integrated luminosity of 5 inverse femtobarns collected with the CMS detector. The analysis is based on the three jets with the highest transverse momenta. The cross section is measured as a function of the invariant mass of the three jets in a range of 445-3270 GeV and in two bins of the maximum rapidity of the jets up to a value of 2. A comparison between the measurement and the prediction from perturbative QCD at next-to-leading order is performed. Within uncertainties, data and theory are in agreement. The sensitivity of the observable to the strong coupling constant alpha[S] is studied. A fit to all data points with 3-jet masses larger than 664 GeV gives a value of the strong coupling constant of alpha[S](MZ) = 0.1171 +/- 0.0013 (exp) +0.0073/-0.0047 (theo).

A strategy to improve the work-hardening behavior of Ti–6Al–4V parts produced by additive manufacturing

Abstract: To improve the mechanical properties of additively manufactured parts, specific heat treatments must be developed. Annealing of electron beam-melted Ti–6Al–4V was performed at sub-transus t...