Institution
Universiti Teknologi Malaysia
Education•Johor Bahru, Malaysia•
About: Universiti Teknologi Malaysia is a education organization based out in Johor Bahru, Malaysia. It is known for research contribution in the topics: Membrane & Adsorption. The organization has 21644 authors who have published 39500 publications receiving 520635 citations.
Topics: Membrane, Adsorption, Control theory, Catalysis, Antenna (radio)
Papers published on a yearly basis
Papers
More filters
••
15 Nov 2012TL;DR: The results indicate the potential for a new use of mesostructured materials as an effective adsorbent for MB, and fit well to the Freundlich isotherm model.
Abstract: In this work, mesostructured silica nanoparticles (MSN(AP)) with high adsorptivity were prepared by a modification with 3-aminopropyl triethoxysilane (APTES) as a pore expander. The performance of the MSN(AP) was tested by the adsorption of MB in a batch system under varying pH (2-11), adsorbent dosage (0.1-0.5 g L(-1)), and initial MB concentration (5-60 mg L(-1)). The best conditions were achieved at pH 7 when using 0.1 g L(-1) MSN(AP) and 60 mg L(-1)MB to give a maximum monolayer adsorption capacity of 500.1 mg g(-1) at 303 K. The equilibrium data were evaluated using the Langmuir, Freundlich, Temkin, and Harkins-Jura isotherms and fit well to the Freundlich isotherm model. The adsorption kinetics was best described by the pseudo-second order model. The results indicate the potential for a new use of mesostructured materials as an effective adsorbent for MB.
139 citations
••
TL;DR: In this paper, a two-sided lid driven cavity with several pairs of heaters and coolers inside is investigated numerically using two-phase mixture model and the governing equations have been discretized using the finite volume method while the SIMPLE algorithm has been introduced to couple the velocity-pressure.
138 citations
••
TL;DR: In this paper, the authors investigated experimentally and numerically the crush response and energy absorption performances of auxetic foam-filled square tubes under quasi-static axial loading, and found that the auxetic foamed square tube is superior to empty and conventional foam filled square tubes in terms of all crashworthiness indicators.
138 citations
••
TL;DR: In this paper, the efficiency of CO2 reduction to CO was greatly enhanced under lower energy visible light irradiations by the deposition of gold-nanoparticles (Au-NPs).
138 citations
••
TL;DR: In this article, the major and minor reactions of EC process with operational parameters, design of EC cell, mass transfer studies and modeling, and industrial wastewater applications are reviewed and compared with conventional coagulation and combinations with other techniques.
Abstract: The conventional coagulation technique of textile wastewater treatments is plagued with the issue of low removal rate of pollutants and generation of a large quantity of sludge. Recently, electrocoagulation (EC) technique gained immense attention due to its efficiency. The technique involves dissolution of the sacrificial anodes to provide an active metal hydroxide as a strong coagulant that destabilizes and amasses particles and then removes them by precipitation or adsorption. EC process is influenced by operating parameters such as applied current density, electrodes material and configuration, type of electrical connection, pH and conductivity of the solution, and mixing state. Consequently, this work reviewed the major and minor reactions of EC process with operational parameters, design of EC cell, mass transfer studies and modeling, and industrial wastewater applications. The work also includes comparison of EC technique with conventional coagulation and combinations with other techniques. Special emphasis is on removal of pollutants from textile wastewater. Further, the electrical energy supplies and cost analysis are also discussed. Even though several publications have covered EC process recently, no review work has treated the systematic process design and how to minimize the effect of passivation layer deposited on the surface of the electrodes. EC process with rotating electrodes has been recommended to reduce this phenomenon. The effect of electrodes geometry is considered to enhance the conductivity of the cell and reduce energy consumption. The studies of ionic mass transfer were not implemented before special by limiting current method during the EC process. Moreover, no aforementioned studies used computational fluid dynamics modeling to present the mass transfer inside the EC reactor.
138 citations
Authors
Showing all 21852 results
Name | H-index | Papers | Citations |
---|---|---|---|
Xin Li | 114 | 2778 | 71389 |
Muhammad Imran | 94 | 3053 | 51728 |
Ahmad Fauzi Ismail | 93 | 1357 | 40853 |
Bin Tean Teh | 92 | 471 | 33359 |
Muhammad Farooq | 92 | 1341 | 37533 |
M. A. Shah | 92 | 583 | 37099 |
Takeshi Matsuura | 85 | 540 | 26188 |
Peter Willett | 76 | 479 | 29037 |
Peter C. Searson | 74 | 374 | 21806 |
Ozgur Kisi | 73 | 478 | 19433 |
Imran Ali | 72 | 300 | 19878 |
S.M. Sapuan | 70 | 713 | 19175 |
Peter J. Fleming | 66 | 529 | 24395 |
Mohammad Jawaid | 65 | 503 | 19471 |
Muhammad Tahir | 65 | 1636 | 23892 |