Showing papers on "Indium tin oxide published in 2012"
TL;DR: In this paper, a high-work-function, low-sheet-resistance graphene anode was used to improve the luminous efficiency of organic light-emitting diodes (OLEDs).
Abstract: Although graphene films have a strong potential to replace indium tin oxide anodes in organic light-emitting diodes (OLEDs), to date, the luminous efficiency of OLEDs with graphene anodes has been limited by a lack of efficient methods to improve the low work function and reduce the sheet resistance of graphene films to the levels required for electrodes1,2,3,4. Here, we fabricate flexible OLEDs by modifying the graphene anode to have a high work function and low sheet resistance, and thus achieve extremely high luminous efficiencies (37.2 lm W–1 in fluorescent OLEDs, 102.7 lm W–1 in phosphorescent OLEDs), which are significantly higher than those of optimized devices with an indium tin oxide anode (24.1 lm W–1 in fluorescent OLEDs, 85.6 lm W–1 in phosphorescent OLEDs). We also fabricate flexible white OLED lighting devices using the graphene anode. These results demonstrate the great potential of graphene anodes for use in a wide variety of high-performance flexible organic optoelectronics. By replacing conventional indium tin oxide (ITO) anodes with high-work-function, low-sheet-resistance graphene anodes, researchers demonstrate flexible fluorescent organic LEDs with extremely high luminous efficiencies of 37.2 lm W–1 for fluorescent devices and 102.7 lm W–1 for phosphorescent devices. These values are significantly higher than those of optimized organic LEDs based on ITO anodes.
1,273 citations
TL;DR: In this paper, a fluorosurfactant-treated poly(3,4-ethylenedioxythiophene):poly(styrenesulfonic acid) (PEDOT:PSS) films were used as anode for stretchable and transparent electrodes.
Abstract: Highly conductive and transparent poly-(3,4-ethylenedioxythiophene):poly(styrenesulfonic acid) (PEDOT:PSS) films, incorporating a fluorosurfactant as an additive, have been prepared for stretchable and transparent electrodes. The fluorosurfactant-treated PEDOT:PSS films show a 35% improvement in sheet resistance (Rs) compared to untreated films. In addition, the fluorosurfactant renders PEDOT:PSS solutions amenable for deposition on hydrophobic surfaces, including pre-deposited, annealed films of PEDOT:PSS (enabling the deposition of thick, highly conductive, multilayer films) and stretchable poly(dimethylsiloxane) (PDMS) substrates (enabling stretchable electronics). Four-layer PEDOT:PSS films have an Rs of 46 Ω per square with 82% transmittance (at 550 nm). These films, deposited on a pre-strained PDMS substrate and buckled, are shown to be reversibly stretchable, with no change to Rs, during the course of over 5000 cycles of 0 to 10% strain. Using the multilayer PEDOT:PSS films as anodes, indium tin oxide (ITO)-free organic photovoltaics are prepared and shown to have power conversion efficiencies comparable to that of devices with ITO as the anode. These results show that these highly conductive PEDOT:PSS films can not only be used as transparent electrodes in novel devices (where ITO cannot be used), such as stretchable OPVs, but also have the potential to replace ITO in conventional devices.
1,016 citations
TL;DR: It is found that very long metallic nanowire network conductors combined with a low temperature laser nano-welding process enabled superior transparent flexible conductors with high transmittance and high electrical conductivity.
Abstract: The future electronics will be soft, flexible and even stretchable to be more human friendly in the form of wearable computers. However, conventional electronic materials are usually brittle. Recently, carbon based materials are intensively investigated as a good candidate for flexible electronics but with limited mechanical and electrical performances. Metal is still the best material for electronics with great electrical properties but with poor transparency and mechanical performance. Here we present a simple approach to develop a synthesis method for very long metallic nanowires and apply them as new types of high performance flexible and transparent metal conductors as an alternative to carbon nanotubes, graphene and short nanowire based flexible transparent conductors and indium tin oxide based brittle transparent conductors. We found that very long metallic nanowire network conductors combined with a low temperature laser nano-welding process enabled superior transparent flexible conductors with high transmittance and high electrical conductivity. Further, we demonstrated highly flexible metal conductor LED circuits and transparent touch panels. The highly flexible and transparent metal conductors can be mounted on any non-planar surfaces and applied for various opto-electronics and ultimately for future wearable electronics.
666 citations
TL;DR: In this paper, the current losses due to parasitic absorption in the indium tin oxide (ITO) and amorphous silicon (a-Si:H) layers at the front of silicon heterojunction solar cells are isolated and quantified.
Abstract: The current losses due to parasitic absorption in the indium tin oxide (ITO) and amorphous silicon (a-Si:H) layers at the front of silicon heterojunction solar cells are isolated and quantified. Quantum efficiency spectra of cells in which select layers are omitted reveal that the collection efficiency of carriers generated in the ITO and doped a-Si:H layers is zero, and only 30% of light absorbed in the intrinsic a-Si:H layer contributes to the short-circuit current. Using the optical constants of each layer acquired from ellipsometry as inputs in a model, the quantum efficiency and short-wavelength current loss of a heterojunction cell with arbitrary a-Si:H layer thicknesses and arbitrary ITO doping can be correctly predicted. A 4 cm2 solar cell in which these parameters have been optimized exhibits a short-circuit current density of 38.1 mA/cm2 and an efficiency of 20.8%.
486 citations
TL;DR: Whether LEDs based on thick-shell nanocrystals, so-called "giant" NQDs, afford enhanced performance compared to their counterparts incorporating thin-shell systems is determined.
Abstract: We use a simple device architecture based on a poly(3,4-ethylendioxythiophene):poly(styrenesulfonate) (PEDOT:PSS)-coated indium tin oxide anode and a LiF/Al cathode to assess the effects of shell thickness on the properties of light-emitting diodes (LEDs) comprising CdSe/CdS core/shell nanocrystal quantum dots (NQDs) as the emitting layer. Specifically, we are interested in determining whether LEDs based on thick-shell nanocrystals, so-called "giant" NQDs, afford enhanced performance compared to their counterparts incorporating thin-shell systems. We observe significant improvements in device performance as a function of increasing shell thickness. While the turn-on voltage remains approximately constant for all shell thicknesses (from 4 to 16 CdS monolayers), external quantum efficiency and maximum luminance are found to be about one order of magnitude higher for thicker shell nanocrystals (≥13 CdS monolayers) compared to thinner shell structures (<9 CdS monolayers). The thickest-shell nanocrystals (16 monolayers of CdS) afforded an external quantum efficiency and luminance of 0.17% and 2000 Cd/m(2), respectively, with a remarkably low turn-on voltage of ~3.0 V.
375 citations
TL;DR: Several applications of graphene films as electrodes in electrical and optical devices are reviewed and the essential requirements are discussed, which include low sheet resistance, high optical transparency and excellent mechanical properties.
Abstract: Graphene is a promising next-generation conducting material with the potential to replace traditional electrode materials such as indium tin oxide in electrical and optical devices. It combines several advantageous characteristics including low sheet resistance, high optical transparency and excellent mechanical properties. Recent research has coincided with increased interest in the application of graphene as an electrode material in transistors, light-emitting diodes, solar cells and flexible devices. However, for more practical applications, the performance of devices should be further improved by the engineering of graphene films, such as through their synthesis, transfer and doping. This article reviews several applications of graphene films as electrodes in electrical and optical devices and discusses the essential requirements for applications of graphene films as electrodes.
366 citations
TL;DR: FeCl(3)-FLGs outperform the current limit of transparent conductors such as indium tin oxide, carbon-nanotube films, and doped graphene materials and are the best transparent conductor for optoelectronic devices.
Abstract: Transparent conductors based on few-layer graphene (FLG) intercalated with ferric chloride (FeCl(3)) have an outstandingly low sheet resistance and high optical transparency. FeCl(3)-FLGs outperform the current limit of transparent conductors such as indium tin oxide, carbon-nanotube films, and doped graphene materials. This makes FeCl(3)-FLG materials the best transparent conductor for optoelectronic devices.
316 citations
TL;DR: Coating copper nanowires to a ratio of 2:1 Cu:Ni gave them a neutral gray color, making them more suitable for use in displays and electrochromic windows, and make cupronickel nanoweires a promising alternative for the sustainable, efficient production of transparent conductors.
Abstract: Nanowires of copper can be coated from liquids to create flexible, transparent conducting films that can potentially replace the dominant transparent conductor, indium tin oxide, in displays, solar cells, organic light-emitting diodes, and electrochromic windows. One issue with these nanowire films is that copper is prone to oxidation. It was hypothesized that the resistance to oxidation could be improved by coating copper nanowires with nickel. This work demonstrates a method for synthesizing copper nanowires with nickel shells as well as the properties of cupronickel nanowires in transparent conducting films. Time- and temperature-dependent sheet resistance measurements indicate that the sheet resistance of copper and silver nanowire films will double after 3 and 36 months at room temperature, respectively. In contrast, the sheet resistance of cupronickel nanowires containing 20 mol % nickel will double in about 400 years. Coating copper nanowires to a ratio of 2:1 Cu:Ni gave them a neutral gray color, making them more suitable for use in displays and electrochromic windows. These properties, and the fact that copper and nickel are 1000 times more abundant than indium or silver, make cupronickel nanowires a promising alternative for the sustainable, efficient production of transparent conductors.
306 citations
TL;DR: Graphene/NW films with a sheet resistance comparable to that of the intrinsic resistance of graphene have been obtained and tested as a transparent electrode replacing indium tin oxide films in electrochromic (EC) devices.
Abstract: Polycrystalline graphene grown by chemical vapor deposition (CVD) on metals and transferred onto arbitrary substrates has line defects and disruptions such as wrinkles, ripples, and folding that adversely affect graphene transport properties through the scattering of the charge carriers. It is found that graphene assembled with metal nanowires (NWs) dramatically decreases the resistance of graphene films. Graphene/NW films with a sheet resistance comparable to that of the intrinsic resistance of graphene have been obtained and tested as a transparent electrode replacing indium tin oxide films in electrochromic (EC) devices. The successful integration of such graphene/NW films into EC devices demonstrates their potential for a wide range of optoelectronic device applications.
306 citations
TL;DR: PA modification of ITO has resulted in materials that are more stable and more compatible with subsequently deposited organic materials, an effective work function that can be tuned by over 1 eV, and energy barriers to hole injection (OLED) or hole-harvesting (OPV) that can been well matched to the frontier orbital energies of the organic active layers, leading to better overall device properties.
Abstract: Transparent metal oxides, in particular, indium tin oxide (ITO), are critical transparent contact materials for applications in next-generation organic electronics, including organic light emitting diodes (OLEDs) and organic photovoltaics (OPVs). Understanding and controlling the surface properties of ITO allows for the molecular engineering of the ITO–organic interface, resulting in fine control of the interfacial chemistries and electronics. In particular, both surface energy matching and work function compatibility at material interfaces can result in marked improvement in OLED and OPV performance. Although there are numerous ways to change the surface properties of ITO, one of the more successful surface modifications is the use of monolayers based on organic molecules with widely variable end functional groups. Phosphonic acids (PAs) are known to bind strongly to metal oxides and form robust monolayers on many different metal oxide materials. They also demonstrate several advantages over other functi...
291 citations
TL;DR: A single-layer graphene film with high conductance and transparency was realized by effective chemical doping and all of the devices showed higher efficiency from the graphene than ITO side, which was attributed to the better transmittance of the graphene electrodes.
Abstract: A single-layer graphene film with high conductance and transparency was realized by effective chemical doping. The conductance of single-layer graphene was increased for more than 400% when it was doped with Au nanoparticles and poly(3,4-ethylenedioxythiophene): poly(styrene sulfonic acid). Then semitransparent organic solar cells based on poly(3-hexylthiophene) (P3HT) and phenyl-C61-butyric acid methyl ester (PCBM) were fabricated with single-layer graphene and indium tin oxide (ITO) as the top and bottom electrodes, respectively. The performance of the devices was optimized by tuning the active layer thickness and doping the single-layer graphene electrodes. The maximum efficiency of 2.7% was observed in the devices with the area of 20 mm2 illuminated from graphene electrode under the AM1.5 solar simulator. It is notable that all of the devices showed higher efficiency from the graphene than ITO side, which was attributed to the better transmittance of the graphene electrodes. In addition, the influence...
TL;DR: A systematic study has been performed in which transparent superhydrophobic surfaces were created on glass, polycarbonate, and poly(methyl methacrylate) (PMMA) substrates using surface-functionalized SiO(2), ZnO, and indium tin oxide (ITO) nanoparticles.
Abstract: It is of significant interest to create surfaces that simultaneously exhibit high water contact angle, low contact angle hysteresis, and high transmission of visible light, as well as mechanical wear resistance for industrial applications. The fabrication of such surfaces has often involved complex or expensive processes, required techniques that were not suitable for a variety of substrates and particles, required surface post-treatment, or lacked wear resistance. A systematic study has been performed in which transparent superhydrophobic surfaces were created on glass, polycarbonate, and poly(methyl methacrylate) (PMMA) substrates using surface-functionalized SiO(2), ZnO, and indium tin oxide (ITO) nanoparticles. The contact angle, contact angle hysteresis, and optical transmittance were measured for samples using all particle-substrate combinations. To examine wear resistance, multiscale wear experiments were performed using an atomic force microscope (AFM) and a water jet apparatus.
TL;DR: In this article, a novel method to significantly enhance the conductivity of poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) films through treatment with a fluoro compound, hexafluoroacetone (HFA).
Abstract: Flexible transparent electrode materials are strongly needed for optoelectronic devices. We report a novel method to significantly enhance the conductivity of poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) films through treatment with a fluoro compound, hexafluoroacetone (HFA). HFA hydrolyzes with water into a geminal diol, 1,1,1,3,3,3-hexafluoropropane-2,2-diol (HFP2OH) that has two –OH groups connected to the middle carbon atom. The conductivity increased from 0.3 to 1164 and 1325 S cm−1 after the treatment with HFA once and four times, respectively. The highly conductive HFA-treated PEDOT:PSS films can have a sheet resistances of 46 Ω □−1 and a transparency of around 83% at 550 nm. These values are comparable to those of indium tin oxide (ITO) on polyethylene terephthalate (PET). The conductivity enhancement is attributed to the HFP2OH-induced phase segregation of some hydrophilic PSSH chains from PEDOT:PSS and the conformational change of the conductive PEDOT chains, driven by the interactions between amphiphilic HFP2OH and PEDOT:PSS. The hydrophobic –CF3groups of HFP2OH preferentially interact with the hydrophobic PEDOT chains of PEDOT:PSS, while the hydrophilic –OH groups preferentially interact with hydrophilic PSS chains. The highly conductive PEDOT:PSS films were used to replace ITO as the transparent anode of polymer solar cells. Polymer solar cells based on poly(3-hexylthiophene) (P3HT) and [6,6]-phenyl-C61-butyric acid methyl ester (PCBM) exhibited a photovoltaic efficiency of 3.57% under simulated AM1.5G illumination, comparable to the control devices with ITO as the anode.
TL;DR: The reduced pressure synthesis of poly(3,4-ethylenedioxythiophene) (PEDOT) with sheet-like morphology has been achieved with the introduction of an amphiphilic triblock copolymer into the oxidant thin film as discussed by the authors.
Abstract: The reduced pressure synthesis of poly(3,4-ethylenedioxythiophene) (PEDOT) with sheet-like morphology has been achieved with the introduction of an amphiphilic triblock copolymer into the oxidant thin film. Addition of the copolymer not only results in an oxidant thin film which remains liquid-like under reduced pressure but also induces structured growth during film formation. PEDOT films were polymerized using the vacuum vapor phase polymerization (VPP) technique, in which we show that maintaining a liquid-like state for the oxidant is essential. The resulting conductivity is equivalent to commercially available indium tin oxide (ITO) with concomitant optical transmission values. PEDOT films can be produced with a variety of thicknesses across a range of substrate materials from plastics to metals to ceramics, with sheet resistances down to 45 Ω/□ (ca. 3400 S·cm–1), and transparency in the visible spectrum of >80% at 65 nm thickness. This compares favorably to ITO and its currently touted replacements.
TL;DR: Schottky-barrier solar cells employing a stack of layer-structured semiconductor molybdenum disulfide (MoS(2)) nanomembranes, synthesized by the chemical-vapor-deposition method, as the critical photoactive layer are demonstrated.
Abstract: We demonstrate Schottky-barrier solar cells employing a stack of layer-structured semiconductor molybdenum disulfide (MoS2) nanomembranes, synthesized by the chemical-vapor-deposition method, as the critical photoactive layer An MoS2 nanomembrane forms a Schottky-barrier with a metal contact by the layer-transfer process onto an indium tin oxide (ITO) coated glass substrate Two vibrational modes in MoS2 nanomembranes, E12g (in-plane) and A1g (perpendicular-to-plane), were verified by Raman spectroscopy With a simple stacked structure of ITO–MoS2–Au, the fabricated solar cell demonstrates a photo-conversion efficiency of 07% for ∼110 nm MoS2 and 18% for ∼220 nm MoS2 The improvement is attributed to a substantial increase in photonic absorption The MoS2 nanomembrane exhibits efficient photo-absorption in the spectral region of 350–950 nm, as confirmed by the external quantum efficiency A sizable increase in MoS2 thickness results in only minor change in Mott–Schottky behavior, indicating that defect density is insensitive to nanomembrane thickness attributed to the dangling-bond-free layered structure
TL;DR: In this paper, the conductivity of poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) films are obtained using ionic liquids as additives.
Abstract: Highly conductive poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) films are obtained using ionic liquids as additives. Upon adding 1-ethyl-3-methylimidazolium tetracyanoborate (EMIM TCB) to the conducting polymer, the conductivity increases to 2084 S cm−1; this is attributed to the phase separation of PSS leading to a structural change in the film. A comparative study with 1-butyl-3-methyl imidazolium tetrafluoroborate (BMIM BF4) shows that EMIM TCB gives higher conductivity and transmittance and can be regarded as one of the most promising additives for the preparation of indium tin oxide (ITO)-free organic devices using PEDOT:PSS/EMIM TCB as electrodes.
TL;DR: In this article, a PANI/tungsten oxide (WO3) nanocomposite was fabricated by electropolymerization of aniline monomers onto indium tin oxide (ITO) glass slides, which were prepared by spin coating technique and followed by annealing at 500 °C for 2 h.
Abstract: Polyaniline (PANI)/tungsten oxide (WO3) nanocomposite films were fabricated by electropolymerization of aniline monomers onto WO3 coated indium tin oxide (ITO) glass slides, which were prepared by spin coating technique and followed by annealing at 500 °C for 2 h. The morphology and crystalline structure of the composite films were studied using Fourier transform infrared (FT-IR) spectroscopy, atomic force microscopy (AFM), X-ray diffraction (XRD), and transmission electron microscopy (TEM). The results confirm chemical interactions between the polymer matrix and the WO3 particles and reveal a well crystallized PANI/WO3 nanocomposite structure. The optical properties and electrochemical capacitive behaviors of the composite films for electrochromic (EC) and energy storage devices applications were investigated using spectroelectrochemistry (SEC), cyclic voltammetry (CV) and galvanostatic charge–discharge measurements. The composite films show dual electrochromism at both positive and negative potentials a...
TL;DR: A layer-by-layer molecular doping process on graphene is reported for forming sandwiched graphene/tetracyanoquinodimethane (TCNQ)/graphene stacked films for polymer solar cell anodes, where the TCNQ molecules were securely embedded between two graphene layers.
Abstract: Large-area graphene grown by chemical vapor deposition (CVD) is a promising candidate for transparent conducting electrode applications in flexible optoelectronic devices such as light-emitting diodes or organic solar cells. However, the power conversion efficiency (PCE) of the polymer photovoltaic devices using a pristine CVD graphene anode is still not appealing due to its much lower conductivity than that of conventional indium tin oxide. We report a layer-by-layer molecular doping process on graphene for forming sandwiched graphene/tetracyanoquinodimethane (TCNQ)/graphene stacked films for polymer solar cell anodes, where the TCNQ molecules (as p-dopants) were securely embedded between two graphene layers. Poly(3-hexylthiophene)/phenyl-C61-butyric acid methyl ester (P3HT/PCBM) bulk heterojunction polymer solar cells based on these multilayered graphene/TCNQ anodes are fabricated and characterized. The P3HT/PCBM device with an anode structure composed of two TCNQ layers sandwiched by three CVD graphene...
TL;DR: A hybrid photoanode for water oxidation consisting of a cyanobacterial photosystem II from Thermosynechococcus elongatus on a mesoporous indium-tin oxide (mesoITO) electrode allows for high protein coverage and direct (mediator-free) electron transfer from PSII to mesoITo.
Abstract: We report on a hybrid photoanode for water oxidation consisting of a cyanobacterial photosystem II (PSII) from Thermosynechococcus elongatus on a mesoporous indium–tin oxide (mesoITO) electrode. The three-dimensional metal oxide environment allows for high protein coverage (26 times an ideal monolayer coverage) and direct (mediator-free) electron transfer from PSII to mesoITO. The oxidation of water occurs with 1.6 ± 0.3 μA cm–2 and a corresponding turnover frequency of approximately 0.18 ± 0.04 (mol O2) (mol PSII)−1 s–1 during red light irradiation. Mechanistic studies are consistent with interfacial electron transfer occurring not only from the terminal quinone QB, but also from the quinone QA through an unnatural electron transfer pathway to the ITO surface.
TL;DR: In this article, a nanocomposite containing poly(N-vinylcarbazole) (PVK) and graphene (G) in solutions and thin films is presented.
Abstract: Materials possessing excellent bacterial toxicity, while presenting low cytotoxicity to human cells, are strong candidates for biomaterials applications. In this study, we present the fabrication of a nanocomposite containing poly(N-vinylcarbazole) (PVK) and graphene (G) in solutions and thin films. Highly dispersed PVK‐G (97-3 w=w%) solutions in various organic and aqueous solvents were prepared by solution mixing and sonication methods. The thermal properties and morphology of the new composite were analyzed using thermal gravimetry analysis (TGA) and atomic force microscopy (AFM), respectively. PVK‐G films were immobilized onto indium tin oxide (ITO) substrates via electrodeposition. AFM was used to characterize the resulting topography of the nanocomposite thin films, while cyclic voltammetry and UV‐vis were used to monitor their successful electrodeposition. The antimicrobial properties of the electrodeposited PVK‐G films and solution-based PVK‐G were investigated against Escherichia coli (E. coli) and Bacillus subtilis (B. subtilis). Microbial growth after exposure to the nanocomposite, metabolic assay and live‐dead assay of the bacterial solutions exposed to PVK‐G presented fewer viable and active bacteria than those exposed to pure PVK or pure graphene solutions. The PVK‐G film inhibited about 80% of biofilm surface coverage whereas the PVK- and G-modified surfaces allowed biofilm formation over almost the whole coated surface (i.e.>80%). The biocompatibility of the prepared PVK‐G solutions on NIH 3T3 cells was evaluated using the MTS cell proliferation assay. A 24 h exposure of the PVK‐G nanocomposite to the NIH 3T3 cells presented 80% cell survival. (Some figures may appear in colour only in the online journal)
TL;DR: By employing antenna elements with different spectral resonances, this work provides a strategy to decouple the nonlinear response of nanomaterials from their linear optical properties.
Abstract: We introduce and experimentally demonstrate the concept of multifrequency optical antennas that are designed for controlling the nonlinear response of materials. These antennas consist of two arms of different lengths, each resonant with one of the incoming frequencies. They are embedded in a nonlinear medium (indium tin oxide) that acts as a receiver. Because the two arms have different spectral resonances, tuning of the antenna gap size has minimal effect on the linear optical properties. However, it strongly affects the nonlinear response. Thus, by employing antenna elements with different spectral resonances, we provide a strategy to decouple the nonlinear response of nanomaterials from their linear optical properties.
TL;DR: Atomic layer deposition is utilized to coat a passivation layer of aluminum-doped zinc oxide (AZO) and aluminum oxide onto electrospun copper nanofibers and remarkably enhance their durability.
Abstract: Copper nanofiber networks, which possess the advantages of low cost, moderate flexibility, small sheet resistance, and high transmittance, are one of the most promising candidates to replace indium tin oxide films as the premier transparent electrode. However, the chemical activity of copper nanofibers causes a substantial increase in the sheet resistance after thermal oxidation or chemical corrosion of the nanofibers. In this work, we utilize atomic layer deposition to coat a passivation layer of aluminum-doped zinc oxide (AZO) and aluminum oxide onto electrospun copper nanofibers and remarkably enhance their durability. Our AZO–copper nanofibers show resistance increase of remarkably only 10% after thermal oxidation at 160 °C in dry air and 80 °C in humid air with 80% relative humidity, whereas bare copper nanofibers quickly become insulating. In addition, the coating and baking of the acidic PEDOT:PSS layer on our fibers increases the sheet resistance of bare copper nanofibers by 6 orders of magnitude,...
TL;DR: This report describes the efforts into the fabrication of the first reported all-carbon solar cell in which all components (the anode, active layer, and cathode) are carbon based.
Abstract: Carbon allotropes possess unique and interesting physical, chemical, and electronic properties that make them attractive for next-generation electronic devices and solar cells. In this report, we describe our efforts into the fabrication of the first reported all-carbon solar cell in which all components (the anode, active layer, and cathode) are carbon based. First, we evaluate the active layer, on standard electrodes, which is composed of a bilayer of polymer sorted semiconducting single-walled carbon nanotubes and C60. This carbon-based active layer with a standard indium tin oxide anode and metallic cathodehasamaximumpowerconversionefficiencyof0.46%underAM1.5Sunillumination.Next,wedescribeoureffortsinreplacingtheelectrodeswith carbon-based electrodes, to demonstrate the first all-carbon solar cell, and discuss the remaining challenges associated with this process.
TL;DR: In this article, defective hexagonal-closed-packed gratings for light extraction were used to obtain broad band lambertian emitters with an improvement in current and power efficiencies by a factor of 1.7 and 1.9, respectively.
Abstract: Defective silica sphere arrays having locally hexagonal-closed-packed structure but lack of long range ordering were incorporated into organic light emitting diodes as grating to extract the waveguided light trapped in the indium tin oxide/organic layers and the glass substrate. Using these defective hexagonal-closed-packed gratings for light extraction, broad band lambertian emitters are obtained due to the periodicity broadening and the random orientation in the gratings, resulting in enhancements in current and power efficiencies by a factor of 1.7 and 1.9, respectively.
TL;DR: In this article, the authors demonstrate the efficacy of low temperature solution-processed flexible metal nanowire networks embedded in a conductive metal oxide nanoparticle matrix as transparent conductors, and investigate their microstructural, optoelectronic, and mechanical properties in attempting to resolve nearly all of the technological issues imposed on silver nanowires networks.
Abstract: Although silver nanowire meshes have already demonstrated sheet resistance and optical transmittance comparable to those of sputter-deposited indium tin oxide thin films, other critical issues including surface morphology, mechanical adhesion and flexibility have to be addressed before widely employing silver nanowire networks as transparent conductors in optoelectronic devices. Here, we demonstrate the efficacy of low temperature solution-processed flexible metal nanowire networks embedded in a conductive metal oxide nanoparticle matrix as transparent conductors, and investigate their microstructural, optoelectronic, and mechanical properties in attempting to resolve nearly all of the technological issues imposed on silver nanowire networks. Surrounding silver nanowires by conductive indium tin oxide nanoparticles offers low wire to wire junction resistance, smooth surface morphology, and excellent mechanical adhesion and flexibility while maintaining the high transmittance and the low sheet resistance. In addition, we discuss the relationship between sheet resistance and transmittance in the silver nanowire composite transparent conductors and their maximum achievable transmittance. Although we have selected silver nanowires and indium tin oxide nanoparticle matrix as demonstration materials, we anticipate that various metal nanowire meshes embedded in various conductive metal oxide nanoparticle matrices can effectively serve as transparent conductors for a wide variety of optoelectronic devices owing to their superior performance, simple, cost-effective, and gentle processing.
01 Jan 2012
TL;DR: In this article, an atomic layer deposition was used to coat a passivation layer of aluminum-doped zinc oxide (AZO) and aluminum oxide onto electrospun copper nanofibers and remarkably enhance their durability.
Abstract: Copper nanofiber networks, which possess the advantages of low cost, moderate flexibility, small sheet resistance, and high transmittance, are one of the most promising candidates to replace indium tin oxide films as the premier transparent electrode. However, the chemical activityofcoppernanofiberscausesasubstantialincreaseinthesheetresistanceafterthermal oxidation or chemical corrosion of the nanofibers. In this work, we utilize atomic layer deposition to coat a passivation layer of aluminum-doped zinc oxide (AZO) and aluminum oxide onto electrospun copper nanofibers and remarkably enhance their durability. Our AZOcopper nanofibers show resistance increase of remarkably only 10% after thermal oxidationat160Cindryairand80Cinhumidairwith80%relativehumidity,whereasbare copper nanofibers quickly become insulating. In addition, the coating and baking of the acidic PEDOT:PSS layer on our fibers increases the sheet resistance of bare copper nanofibers by 6 orders of magnitude, while the AZOCu nanofibers show an 18% increase.
TL;DR: A novel polar-solvent vapor annealing was used to induce a significant structural rearrangement in poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) films in order to improve their electrical conductivity and work function and will allow better use and understanding of polymeric-blend materials.
Abstract: In the present study, a novel polar-solvent vapor annealing (PSVA) was used to induce a significant structural rearrangement in poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) films in order to improve their electrical conductivity and work function. The effects of polar-solvent vapor annealing on PEDOT:PSS were systematically compared with those of a conventional solvent additive method (SAM) and investigated in detail by analyzing the changes in conductivity, morphology, top and bottom surface composition, conformational PEDOT chains, and work function. The results confirmed that PSVA induces significant phase separation between excess PSS and PEDOT chains and a spontaneous formation of a highly enriched PSS layer on the top surface of the PEDOT:PSS polymer blend, which in turn leads to better 3-dimensional connections between the conducting PEDOT chains and higher work function. The resultant PSVA-treated PEDOT:PSS anode films exhibited a significantly enhanced conductivity of up t...
TL;DR: A silver nanowire-indium Tin oxide nanoparticle composite and its successful application to fully solution processed CuInSe(2) solar cells as a window layer are demonstrated, effectively replacing the traditionally sputtered both intrinsic zinc oxide and indium tin oxide layers.
Abstract: A silver nanowire-indium tin oxide nanoparticle composite and its successful application to fully solution processed CuInSe(2) solar cells as a window layer are demonstrated, effectively replacing the traditionally sputtered both intrinsic zinc oxide and indium tin oxide layers. The devices utilizing the nanocomposite window layer demonstrate photovoltaic parameters equal to or even beyond those with sputtered intrinsic zinc oxide and indium tin oxide contacts.
TL;DR: In this paper, the authors present a life cycle assessment of the Hiflex process, in order to compare the environmental impact of avoiding ITO as electrode, and highlight that vacuum processing should be avoided.
TL;DR: In this paper, a III-nitride based blue vertical cavity surface emitting laser using defect-free highly reflective AlInN/GaN distributed Bragg reflectors grown on c-plane free-standing GaN substrates.
Abstract: We report on III-nitride based blue vertical cavity surface emitting lasers using defect-free highly reflective AlInN/GaN distributed Bragg reflectors grown on c-plane free-standing GaN substrates. Lasing is demonstrated at room temperature under pulsed electrical injection. The high lasing threshold current density still prevents devices from continuous wave lasing because of large self-heating. The reasons for such a high threshold are discussed and we show that it mainly comes from large light absorption in the indium tin oxide current spreading layer. Properly tuning both its thickness and its position with respect to the electrical field could remarkably decrease the threshold.