Showing papers on "Low-power electronics published in 2003"

A low-power low-noise CMOS amplifier for neural recording applications

Abstract: There is a need among scientists and clinicians for low-noise low-power biosignal amplifiers capable of amplifying signals in the millihertz-to-kilohertz range while rejecting large dc offsets generated at the electrode-tissue interface. The advent of fully implantable multielectrode arrays has created the need for fully integrated micropower amplifiers. We designed and tested a novel bioamplifier that uses a MOS-bipolar pseudoresistor element to amplify low-frequency signals down to the millihertz range while rejecting large dc offsets. We derive the theoretical noise-power tradeoff limit - the noise efficiency factor - for this amplifier and demonstrate that our VLSI implementation approaches this limit by selectively operating MOS transistors in either weak or strong inversion. The resulting amplifier, built in a standard 1.5-/spl mu/m CMOS process, passes signals from 0.025Hz to 7.2 kHz with an input-referred noise of 2.2 /spl mu/Vrms and a power dissipation of 80 /spl mu/W while consuming 0.16 mm/sup 2/ of chip area. Our design technique was also used to develop an electroencephalogram amplifier having a bandwidth of 30 Hz and a power dissipation of 0.9 /spl mu/W while maintaining a similar noise-power tradeoff.

Leakage current: Moore's law meets static power

Abstract: Off-state leakage is static power, current that leaks through transistors even when they are turned off. The other source of power dissipation in today's microprocessors, dynamic power, arises from the repeated capacitance charge and discharge on the output of the hundreds of millions of gates in today's chips. Until recently, only dynamic power has been a significant source of power consumption, and Moore's law helped control it. However, power consumption has now become a primary microprocessor design constraint; one that researchers in both industry and academia will struggle to overcome in the next few years. Microprocessor design has traditionally focused on dynamic power consumption as a limiting factor in system integration. As feature sizes shrink below 0.1 micron, static power is posing new low-power design challenges.

Razor: a low-power pipeline based on circuit-level timing speculation

Abstract: With increasing clock frequencies and silicon integration, power aware computing has become a critical concern in the design of embedded processors and systems-on-chip. One of the more effective and widely used methods for power-aware computing is dynamic voltage scaling (DVS). In order to obtain the maximum power savings from DVS, it is essential to scale the supply voltage as low as possible while ensuring correct operation of the processor. The critical voltage is chosen such that under a worst-case scenario of process and environmental variations, the processor always operates correctly. However, this approach leads to a very conservative supply voltage since such a worst-case combination of different variabilities is very rare. In this paper, we propose a new approach to DVS, called Razor, based on dynamic detection and correction of circuit timing errors. The key idea of Razor is to tune the supply voltage by monitoring the error rate during circuit operation, thereby eliminating the need for voltage margins and exploiting the data dependence of circuit delay. A Razor flip-flop is introduced that double-samples pipeline stage values, once with a fast clock and again with a time-borrowing delayed clock. A metastability-tolerant comparator then validates latch values sampled with the fast clock. In the event of timing error, a modified pipeline mispeculation recovery mechanism restores correct program state. A prototype Razor pipeline was designed in a 0.18 /spl mu/m technology and was analyzed. Razor energy overhead during normal operation is limited to 3.1%. Analyses of a full-custom multiplier and a SPICE-level Kogge-Stone adder model reveal that substantial energy savings are possible for these devices (up to 64.2%) with little impact on performance due to error recovery (less than 3%).

Single-ISA heterogeneous multi-core architectures: the potential for processor power reduction

Abstract: This paper proposes and evaluates single-ISA heterogeneous multi-core architectures as a mechanism to reduce processor power dissipation. Our design incorporates heterogeneous cores representing different points in the power/performance design space; during an application's execution, system software dynamically chooses the most appropriate core to meet specific performance and power requirements. Our evaluation of this architecture shows significant energy benefits. For an objective function that optimizes for energy efficiency with a tight performance threshold, for 14 SPEC benchmarks, our results indicate a 39% average energy reduction while only sacrificing 3% in performance. An objective function that optimizes for energy-delay with looser performance bounds achieves, on average, nearly a factor of three improvements in energy-delay product while sacrificing only 22% in performance. Energy savings are substantially more than chip-wide voltage/frequency scaling.

Runtime power monitoring in high-end processors: methodology and empirical data

Abstract: With power dissipation becoming an increasingly vexing problem across many classes of computer systems, measuring power dissipation of real, running systems has become crucial for hardware and software system research and design. Live power measurements are imperative for studies requiring execution times too long for simulation, such as thermal analysis. Furthermore, as processors become more complex and include a host of aggressive dynamic power management techniques, per-component estimates of power dissipation have become both more challenging as well as more important. In this paper we describe our technique for a coordinated measurement approach that combines real total power measurement with performance-counter-based, per-unit power estimation. The resulting tool offers live total power measurements for Intel Pentium 4 processors, and also provides power breakdowns for 22 of the major CPU subunits over minutes of SPEC2000 and desktop workload execution. As an example application, we use the generated component power breakdowns to identify program power phase behaviour. Overall, this paper demonstrates a processor power measurement and estimation methodology and also gives experiences and empirical application results that can provide a basis for future power-aware research.

A 12-bit 75-MS/s pipelined ADC using open-loop residue amplification

Abstract: Precision amplifiers dominate the power dissipation in most high-speed pipelined analog-to-digital converters (ADCs). We propose a digital background calibration technique as an enabling element to replace precision amplifiers by simple power-efficient open-loop stages. In the multibit first stage of a 12-bit 75-MSamples/s proof-of-concept prototype, we achieve more than 60% residue amplifier power savings over a conventional implementation. The ADC has been fabricated in a 0.35-/spl mu/m double-poly quadruple-metal CMOS technology and achieves typical differential and integral nonlinearity within 0.5 LSB and 0.9 LSB, respectively. At Nyquist input frequencies, the measured signal-to-noise ratio is 67 dB and the total harmonic distortion is -74 dB. The IC consumes 290 mW at 3 V and occupies 7.9 mm/sup 2/.

A high-speed oscillator-based truly random number source for cryptographic applications on a smart card IC

Abstract: The design of a high-speed IC random number source macro-cell, suitable for integration in a smart card microcontroller, is presented. The oscillator sampling technique is exploited and a jittered oscillator which features an amplified thermal noise source has been designed in order to increase the output throughput and the statistical quality of the generated bit sequences. The oscillator feedback loop acts as an offset compensation for the noise amplifier, thus solving one of the major issues in this kind of circuit. A numerical model for the proposed system has been developed which allows us to carry out an analytical expression for the transition probability between successive bits in the output stream. A prototype chip has been fabricated in a standard digital 0.18 /spl mu/m n-well CMOS process which features a 10 Mbps throughput and fulfills the NIST FIPS and correlation-based tests for randomness. The macro-cell area, excluding pads, is 0.0016 mm/sup 2/ (184 /spl mu/m /spl times/ 86 /spl mu/m) and a 2.3 mW power consumption has been measured.

Dynamic-sleep transistor and body bias for active leakage power control of microprocessors

Abstract: In order to manage the active power consumption of high-performance digital designs, active leakage control techniques are required to provide significant leakage power savings coupled with fast time constants for entering and exiting idle mode. In this paper, dynamic sleep transistors and body bias are used in conjunction with clock gating to control active leakage for a 32-bit integer execution core in 130-nm CMOS technology. Measurements on pMOS sleep transistor reveal that lowest-leakage state is reached in less than 1 /spl mu/s, resulting in 37/spl times/ reduction in leakage power, while reactivation of block is achieved in less than two clock cycles. PMOS body bias reduces leakage power by 2/spl times/ with no performance penalty, and similar reactivation time. Power measurements at 4 GHz, 1.3 V, 75/spl deg/C demonstrate 8% total power reduction using dynamic body bias and 15% power reduction using a pMOS sleep transistor, for a typical activity profile.

An ultralow-energy ADC for Smart Dust

Abstract: A low-energy successive approximation analog-to-digital converter (ADC) targeted for use in distributed sensor networks is presented The individual nodes combine sensing, computation, communications, and power into a tiny volume Energy is extremely limited, forcing the nodes to operate with very low duty cycles This paper describes the design and implementation of an ADC to meet the unique requirements of sensor networks The ADC reported here consumes 31 pJ/8-bit sample at 1-V supply and 100 kS/s, with a standby power consumption of 70 pW This energy consumption is one of the lowest ever reported

A low-voltage low-power voltage reference based on subthreshold MOSFETs

Abstract: In this work, a new low-voltage low-power CMOS voltage reference independent of temperature is presented. It is based on subthreshold MOSFETs and on compensating a PTAT-based variable with the gate-source voltage of a subthreshold MOSFET. The circuit, designed with a standard 1.2-/spl mu/m CMOS technology, exhibits an average voltage of about 295 mV with an average temperature coefficient of 119 ppm//spl deg/C in the range -25 to +125/spl deg/C. A brief study of gate-source voltage behavior with respect to temperature in subthreshold MOSFETs is also reported.

Power efficient charge pump in deep submicron standard CMOS technology

Abstract: A power-efficient charge pump is proposed. The use of low-voltage transistors and of a simple two-phase clocking scheme permits the use of higher operating frequencies compared to conventional solutions, thus obtaining high current, high efficiency, and small area. Measurements show good results for frequencies around 100 MHz. Two test patterns have been fabricated, one with three stages and one with five stages, in a 1.8-V 0.18-/spl mu/m triple-well standard CMOS digital process (six metals). High-voltage capacitors have been implemented using metal to metal parasitic capacitance.

Full chip leakage-estimation considering power supply and temperature variations

Abstract: Leakage power is emerging as a key design challenge in current and future CMOS designs. Since leakage is critically dependent on operating temperature and power supply, we present a full chip leakage estimation technique which accurately accounts for power supply and temperature variations. State of the art techniques are used to compute the thermal and power supply profile of the entire chip. Closed-form models are presented which relate leakage to temperature and VDD variations. These models coupled with the thermal and VDD profile are used to generate an accurate full chip leakage estimation technique considering environmental variations. The results of this approach are demonstrated on large-scale industrial designs.

Understanding and minimizing ground bounce during mode transition of power gating structures

Abstract: We introduce and analyze the ground bounce due to power mode transition in power gating structures. To reduce the ground bounce, we propose novel power gating structures in which sleep transistors are turned on in a non-uniform stepwise manner. Our power gating structures reduce the magnitude of peak current and voltage glitches in the power distribution network as well as the minimum time required to stabilize power and ground. Experimental simulation results with PowerSpice fixtured in a package model demonstrate the effectiveness of the proposed power gate switching noise reduction techniques.

An experimental coin-sized radio for extremely low-power WPAN (IEEE 802.15.4) application at 2.4 GHz

Abstract: An experimental 2.4-GHz CMOS radio composed of RF and digital circuits for the low-power and low-rate preliminary IEEE802.15.4 WPAN is reported, consuming 21 mW in receive mode and 30 mW in transmit mode. The RF design focus is to maximize linearity for a given power consumption using linearization methods which lead an order of magnitude improvement in LNA/mixer IIP3/power performance. Chip-on-PCB technology allows implementation of a coin-sized radio at very low cost, which also provides 3 dBi gain patch antenna and high Q (>50) inductors.

Combined Dynamic Voltage Scaling and Adaptive Body Biasing for Heterogeneous Distributed Real-time Embedded Systems

Abstract: While dynamic power consumption has traditionally been the primary source of power consumption, leakage power is becoming an increasingly important concern as technology feature size continues to shrink. Previous system-level approaches focus on reducing power consumption without considering leakage power consumption. To overcome this limitation, we propose a two-phase approach to combine dynamic voltage scaling (DVS) and adaptive body biasing (ABB) for distributed real-time embedded systems. DVS is a powerful technique for reducing dynamic power consumption quadratically. However, DVS often requires a reduction in the threshold voltage that increases subthreshold leakage current exponentially and, hence, subthreshold leakage power consumption. ABB, which exploits the exponential dependence of subthreshold leakage power on the threshold voltage, is effective in managing leakage power consumption. We first derive an energy consumption model to determine the optimal supply voltage and body bias voltage under a given clock frequency. Then, we analyze the tradeoff between energy consumption and clock period to allocate slack to a set of tasks with precedence relationships and real-time constraints. Based on this two-phase approach, we propose a new system-level scheduling algorithm that can optimize both dynamic power and leakage power consumption by performing DVS and ABB simultaneously for distributed real-time embedded systems. Experimental results show that the average power reduction of our technique with respect to DVS alone is 37.4% for the 70-nm technology.

A 1.8-V 6-bit 1.3-GHz flash ADC in 0.25-/spl mu/m CMOS

Abstract: The design and optimization of a high-speed low-voltage CMOS flash analog-to-digital converter (ADC) are presented. The optimization procedures used during the design give the needed specifications of the different building blocks. Also, an extensive description of the implemented digital error correction technique is described. The used analog power supply is only 1.8 V. The maximum sampling speed is 1.3 GHz. The signal-to-noise-plus-distortion ratio (SNDR) at 133 kHz is 33.2 dB, and the SNDR at 500 MHz is 32 dB. The total power consumption of the converter at full speed is 600 mW and the total active area is only 0.13 mm/sup 2/. The ADC is implemented in a 0.25-/spl mu/m pure digital CMOS technology.

CMOS VLSI implementation of a low-power logarithmic converter

Abstract: We present a unique 32-bit binary-to-binary logarithm converter including its CMOS VLSI implementation. The converter is implemented using combinational logic only and it calculates a logarithm approximation in a single clock cycle. Unlike other complex logarithm correcting algorithms, three unique algorithms are developed and implemented with low-power and fast circuits that reduce the maximum percent errors that result from binary-to-binary logarithm conversion to 0.9299 percent, 0.4314 percent, and 0.1538 percent. Fast 4, 16, and 32-bit leading-one detector circuits are designed to obtain the leading-one position of an input binary word. A 32-word/spl times/5-bit MOS ROM is used to provide 5-bit integers based on the corresponding leading-one position. Both converter area and speed have been considered in the design approach, resulting in the use of a very efficient 32-bit logarithmic shifter in the 32-bit logarithmic converter. The converter is implemented using 0.6/spl mu/m CMOS technology, and it requires 1,600/spl lambda//spl times/2,800/spl lambda/ of chip area. Simulations of the CMOS design for the 32-bit logarithmic converter, operating at V/sub DD/ equal to 5 volts, run at 55 MHz, and the converter consumes 20 milliwatts.

A low-power 2.4-GHz transmitter/receiver CMOS IC

Abstract: A 2.4-GHz CMOS receiver/transmitter incorporates circuit stacking and noninvasive baseband filtering to achieve a high sensitivity with low power dissipation. Using a single 1.6-GHz local oscillator, the transceiver employs two upconversion and downconversion stages while providing on-chip image rejection filtering. Realized in a 0.25-/spl mu/m digital CMOS technology, the receiver exhibits a noise figure of 6 dB and consumes 17.5 mW from a 2.5-V supply, and the transmitter delivers an output power of 0 dBm with a power consumption of 16 mW.

A novel hybrid pass logic with static CMOS output drive full-adder cell

Abstract: A novel design of a 1-bit full adder cell featuring a hybrid CMOS logic style is proposed. The simultaneous generation of XOR and XNOR outputs by pass logic is advantageously exploited in a novel complementary CMOS stage to produce full-swing and balanced outputs so that adder cells can be cascaded without buffer insertion. The increase in transistor count of the complementary CMOS stage is compensated by its reduction in layout complexity. Comparing with other 1-bit adder cells using different but uniform logic styles, simulation results show that it is very power efficient and has lower power-delay product over a wide range of voltages.

Ultra-low-power DLMS adaptive filter for hearing aid applications

Abstract: We present an ultra-low-power, delayed least mean square (DLMS) adaptive filter operating in the subthreshold region for hearing aid applications. Subthreshold operation was accomplished by using a parallel architecture with pseudo nMOS logic style. The parallel architecture enabled us to operate the system at a lower clock rate and reduced supply voltage while maintaining the same throughput. Pseudo nMOS logic operating in the subthreshold region (subpseudo nMOS) provided better power-delay product than subthreshold CMOS (sub-CMOS) logic. Simulation results show that the DLMS adaptive filter can operate at 22 kHz using a 400-mV supply voltage to achieve 91% improvement in power compared to a nonparallel, CMOS implementation. To validate the robust operation of subthreshold logics, a 0.35 /spl mu/m, 23.1 kHz, 21.4 nW, 8/spl times/8 carry save array multiplier test chip was fabricated where an adaptive body biasing scheme is used for compensating process, supply and temperature variations. The test chip showed stable operation at a supply voltage of 0.30 V, which is even lower than the threshold voltages of the pMOS (0.82 V) and nMOS (0.67 V) transistors.

Cryogenic wide-band ultra-low-noise IF amplifiers operating at ultra-low DC power

Abstract: This paper describes cryogenic broad-band amplifiers with very low power consumption and very low noise for the 4-8-GHz frequency range. At room temperature, the two-stage InP-based amplifier has a gain of 27 dB and a noise temperature of 31 K with a power consumption of 14.4 mW per stage, including bias circuitry. When cooled to 15 K, an input noise temperature of 1.4 K is obtained at 5.7 mW per stage. At 0.51 mW per stage, the input noise increases to 2.4 K. The noise measurements have been repeated at different laboratories using different methods and are found consistent.

Effectiveness of adaptive supply voltage and body bias for reducing impact of parameter variations in low power and high performance microprocessors

Abstract: Adaptive supply voltage as well as adaptive body bias may be used to control the frequency and leakage distribution of fabricated microprocessor dies. Test chip measurements show that adaptive V/sub CC/ is effective in reducing the impact of parameter variations on frequency, active power, and leakage power of microprocessors when 20 mV V/sub CC/ resolution is used. Using adaptive V/sub CC/ together with adaptive V/sub BS/ or within-die body bias is much more effective than using any of them individually.

A single-V/sub t/ low-leakage gated-ground cache for deep submicron

Abstract: In this paper, we propose a novel integrated circuit and architectural level technique to reduce leakage power consumption in high-performance cache memories using single V/sub t/ (transistor threshold voltage) process. We utilize the concept of gated-ground (nMOS transistor inserted between ground line and SRAM cell) to achieve a reduction in leakage energy without significantly affecting performance. Experimental results on gated-ground caches show that data is retained (DRG-Cache) even if the memory is put in the standby mode of operation. Data is restored when the gated-ground transistor is turned on. Turning off the gated-ground transistor in turn gives a large reduction in leakage power. This technique requires no extra circuitry; the row decoder itself can be used to control the gated-ground transistor. The technique is applicable to data and instruction caches as well as different levels of cache hierarchy, such as the L1, L2, or L3 caches. We fabricated a test chip in TSMC 0.25-/spl mu/m technology to show the data retention capability and the cell stability of the DRG-Cache. Our simulation results on 100-nm and 70-nm processes (Berkeley Predictive Technology Model) show 16.5% and 27% reduction in consumed energy in L1 cache and 50% and 47% reduction in L2 cache, respectively, with less than 5% impact on execution time and within 4% increase in area overhead.

Zigzag super cut-off CMOS (ZSCCMOS) block activation with self-adaptive voltage level controller: an alternative to clock-gating scheme in leakage dominant era

Abstract: A block activation/deactivation technique uses zigzag super cut-off CMOS to improve wake up time by 8/spl times/ in 0.6 /spl mu/m CMOS versus super cutoff CMOS. Our clock-gating substitute achieves a 200 ps wake-up time and 3 orders of magnitude leakage reduction for leakage dominant LSI's.

A practical micropower programmable bandpass filter for use in bionic ears

Abstract: Subthreshold Gm-C filters offer the low power and wide tunable range required for use in fully implantable bionic ears. The major design challenge that must be met is increasing the linear range. A capacitive-attenuation technique is presented and refined to allow the construction of wide-linear-range bandpass filters with greater than 1 V/sub pp/ swings. For a 100-200 Hz fully differential filter with second-order roll off slopes and greater than 60 dB dynamic range, experimental results from a 1.5-/spl mu/m, 2.8-V BiCMOS chip yield only 0.23 /spl mu/W power consumption; for a 5-10 kHz filter with the same specifications the power only increased to 6.36 /spl mu/W. Fully differential filters with first-order slopes had a dynamic range of 66 dB and power consumptions of 0.12 and 3.36 /spl mu/W in the 100-200 Hz and 5-10 kHz cases, respectively. We show that our experimental results of noise and linear range are in good accord with theoretical estimates of these quantities.

Domino logic with variable threshold voltage keeper

Abstract: A variable threshold voltage keeper circuit technique is proposed for simultaneous power reduction and speed enhancement of domino logic circuits. The threshold voltage of a keeper transistor is dynamically modified during circuit operation to reduce contention current without sacrificing noise immunity. The variable threshold voltage keeper circuit technique enhances circuit evaluation speed by up to 60% while reducing power dissipation by 35% as compared to a standard domino (SD) logic circuit. The keeper size can be increased with the proposed technique while preserving the same delay or power characteristics as compared to a SD circuit. The proposed domino logic circuit technique offers 14% higher noise immunity as compared to a SD circuit with the same evaluation delay characteristics. Forward body biasing the keeper transistor is also proposed for improved noise immunity as compared to a SD circuit with the same keeper size. It is shown that by applying forward and reverse body biased keeper circuit techniques, the noise immunity and evaluation speed of domino logic circuits are simultaneously enhanced.

A low-power precomputation-based fully parallel content-addressable memory

Abstract: This paper presents a novel VLSI architecture for a fully parallel precomputation-based content-addressable memory (PB-CAM) with low-power, low-cost, and low-voltage features. This design is based on a precomputation approach that saves not only power consumption of the CAM system, but also reduces transistor count and operating voltage of the CAM cell. In addition, the proposed PB-CAM word structure adopts the static pseudo-nMOS circuit design to improve system performance. The whole design was fabricated with the TSMC 0.35-/spl mu/m single-poly quadruple-metal CMOS process. With a 128 words by 30 bits CAM size, the measurement results indicate that the proposed circuit works up to 100 MHz with power consumption of 33 mW at 3.3-V supply voltage and works up to 30 MHz under 1.5-V supply voltage.

A low-power adaptive bandwidth PLL and clock buffer with supply-noise compensation

Abstract: This paper describes a fully integrated low-jitter CMOS phase-locked loop and clock buffer for low-power digital systems with a wide range of operating frequencies. The design uses static CMOS inverters as a building block of the voltage-controlled oscillator and clock buffering. To reduce supply-induced jitter, programmable circuits with opposite sensitivity compensate for the delay variations. Both elements have supply-induced delay sensitivity of /spl les/0.1%-delay/1%-V/sub DD/. The design is fabricated in 0.25-/spl mu/m CMOS technology and consumes 10mW from a 2.5-V supply. The experimental results verify that the proposed methods significantly improve the jitter.

Modeling and estimation of total leakage current in nano-scaled-CMOS devices considering the effect of parameter variation

Abstract: In this paper we have developed analytical models to estimate the mean and the standard deviation in the gate, the subthreshold, the reverse biased source/drain junction band-to-band tunneling (BTBT) and the total leakage in scaled CMOS devices considering variation in process parameters like device geometry, doping profile, flat-band voltage and supply voltage. We have verified the model using Monte Carlo simulation using an NMOS device of 50 nm effective length and analyzed the results to enumerate the effect of different process parameters on the individual components and the total leakage.

Low-power high-level synthesis for FPGA architectures

Abstract: This paper addresses two aspects of low-power design for FPGA circuits. First, we present an RT-level power estimator for FPGAs with consideration of wire length. The power estimator closely reflects both dynamic and static power contributed by various FPGA components in 0.1 /spl mu/m technology. The power estimation error is 16.2% on average. Second, we present a low power high level synthesis system, named LOPASS, for FPGA designs. It includes two algorithms for power consumption reduction: (i) a simulated annealing engine that carries out resource selection function unit binding, scheduling, register binding, and data pat. generation simultaneously to effectively reduce power; (ii) an enhanced weighted bipartite matching algorithm that is able to reduce the total amount of MUX ports by 22.7%. Experimental results show that LOPASS is able to reduce-power consumption by 35.8% compared to the results-of -Synopsys' Behavioral Compiler.