Showing papers on "Amorphous solid published in 1998"

Optical properties of metallic films for vertical-cavity optoelectronic devices.

Abstract: We present models for the optical functions of 11 metals used as mirrors and contacts in optoelectronic and optical devices: noble metals (Ag, Au, Cu), aluminum, beryllium, and transition metals (Cr, Ni, Pd, Pt, Ti, W). We used two simple phenomenological models, the Lorentz-Drude (LD) and the Brendel-Bormann (BB), to interpret both the free-electron and the interband parts of the dielectric response of metals in a wide spectral range from 0.1 to 6 eV. Our results show that the BB model was needed to describe appropriately the interband absorption in noble metals, while for Al, Be, and the transition metals both models exhibit good agreement with the experimental data. A comparison with measurements on surface normal structures confirmed that the reflectance and the phase change on reflection from semiconductor-metal interfaces (including the case of metallic multilayers) can be accurately described by use of the proposed models for the optical functions of metallic films and the matrix method for multilayer calculations.

Solid-state dye-sensitized mesoporous TiO2 solar cells with high photon-to-electron conversion efficiencies

Abstract: Solar cells based on dye-sensitized mesoporous films of TiO2 arelow-cost alternatives to conventional solid-state devices1. Impressive solar-to-electrical energy conversion efficiencies have been achieved with such films when used in conjunction with liquid electrolytes2. Practical advantages may be gained by the replacement of the liquid electrolyte with a solid charge-transport material. Inorganic p-type semiconductors3,4 and organic materials5,6,7,8,9 have been tested in this regard, but in all cases the incident monochromatic photon-to-electron conversion efficiency remained low. Here we describe a dye-sensitized heterojunction of TiO2 with the amorphous organic hole-transport material 2,2′,7,7′-tetrakis(N,N-di-p-methoxyphenyl-amine)9,9′-spirobifluorene (OMeTAD; refs. 10 and 11). Photoinduced charge-carrier generation at the heterojunction is very efficient. A solar cell based on OMeTAD converts photons to electric current with a high yield of 33%.

Nanocomposite polymer electrolytes for lithium batteries

Abstract: Ionically conducting polymer membranes (polymer electrolytes) might enhance lithium-battery technology by replacing the liquid electrolyte currently in use and thereby enabling the fabrication of flexible, compact, laminated solid-state structures free from leaks and available in varied geometries1. Polymer electrolytes explored for these purposes are commonly complexes of a lithium salt (LiX) with a high-molecular-weight polymer such as polyethylene oxide (PEO). But PEO tends to crystallize below 60 °C, whereas fast ion transport is a characteristic of the amorphous phase. So the conductivity of PEO–LiX electrolytes reaches practically useful values (of about 10−4 S cm−1) only at temperatures of 60–80 °C. The most common approach for lowering the operational temperature has been to add liquid plasticizers, but this promotes deterioration of the electrolyte's mechanical properties and increases its reactivity towards the lithium metal anode. Here we show that nanometre-sized ceramic powders can perform as solid plasticizers for PEO, kinetically inhibiting crystallization on annealing from the amorphous state above 60 °C. We demonstrate conductivities of around 10−4 S cm−1 at 50 °C and 10−5 S cm−1 at 30 °C in a PEO–LiClO4 mixture containing powders of TiO2 and Al2O3 with particle sizes of 5.8–13 nm. Further optimization might lead to practical solid-state polymer electrolytes for lithium batteries.

Theory of the field-effect mobility in amorphous organic transistors

Abstract: The field-effect mobility in an organic thin-film transistor is studied theoretically. From a percolation model of hopping between localized states and a transistor model an analytic expression for the field-effect mobility is obtained. The theory is applied to describe the experiments by Brown et al. [Synth. Met. 88, 37 (1997)] on solution-processed amorphous organic transistors, made from a polymer (polythienylene vinylene) and from a small molecule (pentacene). Good agreement is obtained, with respect to both the gate voltage and the temperature dependence of the mobility.

Novel materials synthesis by mechanical alloying/milling

Abstract: An account is given of the research that has been carried out on mechanical alloying/milling (MA/MM) during the past 25 years. Mechanical alloying, a high energy ball milling process, has established itself as a viable solid state processing route for the synthesis of a variety of equilibrium and non-equilibrium phases and phase mixtures. The process was initially invented for the production of oxide dispersion strengthened (ODS) Ni-base superalloys and later extended to other ODS alloys. The success of MA in producing ODS alloys with better high temperature capabilities in comparison with other processing routes is highlighted. Mechanical alloying has also been successfully used for extending terminal solid solubilities in many commercially important metallic systems. Many high melting intermetallics that are difficult to prepare by conventional processing techniques could be easily synthesised with homogeneous structure and composition by MA. It has also, over the years, proved itself to be superior to rapid solidification processing as a non-equilibrium processing tool. The considerable literature on the synthesis of amorphous, quasicrystalline, and nanocrystalline materials by MA is critically reviewed. The possibility of achieving solid solubility in liquid immiscible systems has made MA a unique process. Reactive milling has opened new avenues for the solid state metallothermic reduction and for the synthesis of nanocrystalline intermetallics and intermetallic matrix composites. Despite numerous efforts, understanding of the process of MA, being far from equilibrium, is far from complete, leaving large scope for further research in this exciting field.

Amorphous silica nanowires: Intensive blue light emitters

Abstract: We report large-scale synthesis of silica nanowires (SiONWs) using an excimer laser ablation method. Silica was produced in the form of amorphous nanowires at a diameter of ∼15 nm and a length up to hundreds micrometers. The SiONWs emit stable and high brightness blue light at energies of 2.65 and 3.0 eV. The intensity of the emission is two orders of magnitude higher than that of porous silicon. The SiONWs may have potential applications in high-resolution optical heads of scanning near-field optical microscope or nanointerconnections in future integrated optical devices.

Characterization of Sol‐Gel‐Derived Cobalt Oxide Xerogels as Electrochemical Capacitors

Abstract: Very fine cobalt oxide xerogel powders were prepared using a unique solution chemistry associated with the sol-gel process The effect of thermal treatment on the surrace area, pore volume, crystallinity, particle structure, and corresponding electrochemical properties of the resulting xerogels was investigated and found to have significant effects on all of these properties The xerogel remained amorphous as Co(OH) 2 up to 160°C, and exhibited maxima in both the surface area and pore volume at this temperature With an increase in the temperature above 200°C, both the surface area and pore volume decreased sharply, because the amorphous Co(OH) 2 decomposed to form CoO that was subsequently oxidized to form crystalline Co 3 O 4 In addition, the changes in the surface area, pore volume, crystallinity, and particle structure all had significant but coupled effects on the electrochemical properties of the xerogels A maximum capacitance of 291 F/g was obtained for an electrode prepared with the CoO x xerogel calcined at 150°C, which was consistent with the maxima exhibited in both the surface area and pore volume; this capacitance was attributed solely to a surface redox mechanism The cycle life of this electrode was also very stable for many thousands of cycles

Amorphous and Microcrystalline Silicon Solar Cells: Modeling, Materials and Device Technology

Abstract: Part I: Technology of Amorphous and Microcrystalline Silicon Solar Cells. 1. Introduction. 2. Deposition of Amorphous and Microcrystalline Silicon. 3. Optical, Electronic and Structural Properties. 4. Technology of Solar Cells. 5. Metastability. Part II: Modeling of Amorphous Silicon Solar Cells. 6. Electrical Device Modeling. 7. Optical Device Modeling. 8. Integrated Optical and Electrical Modeling. Index.

Carbon nitride deposited using energetic species: a review on xps studies

Abstract: This paper reviews x-ray photoelectron spectroscopy studies on carbon nitride (CN) and reports on results obtained from CN thin films prepared by mass selected ion-beam deposition. The core-level spectra of samples deposited at room temperature show that nitrogen is incorporated into the amorphous network in two different bonding configurations; carbon has three main bonding configurations whose relative contributions vary as a function of the nitrogen content. For samples deposited at elevated temperatures an ordering of the amorphous CN network towards a crystalline graphitelike structure is observed. Furthermore, both deposition at elevated temperatures (350 \ifmmode^\circ\else\textdegree\fi{}C) and post-deposition ion irradiation have a strong influence on the bonding configuration in the CN films. Based on these results and the results reported in the reviewed literature a picture of the microstructure of carbon nitride deposited using energetic species is developed.

Nanoscale silicon wires synthesized using simple physical evaporation

Abstract: We report the large-scale synthesis of silicon nanowires (SiNWs) using a simple but effective approach. High purity SiNWs of uniform diameters around 15 nm were obtained by sublimating a hot-pressed silicon powder target at 1200 °C in a flowing carrier gas environment. The SiNWs emit stable blue light which seems unrelated to quantum confinement, but related to an amorphous overcoating layer of silicon oxide. Our approach can be used, in principle, as a general method for synthesis of other one-dimensional semiconducting, or conducting nanowires.

Sonochemical Preparation and Size-Dependent Properties of Nanostructured CoFe2O4 Particles

Abstract: Nanostructured CoFe2O4 particles were prepared by a sonochemical approach, first by preparation of the amorphous precursor powders, followed by heat treatment at relatively very low temperatures. The precursor was prepared by sonochemical decomposition of solutions of volatile organic precursors, Fe(CO)5 and Co(NO)(CO)3, in Decalin at 273 K, under an oxygen pressure of 100−150 kPa. The amorphous nature of these particles was confirmed by various techniques, such as scanning and transmission electron microscopy (SEM and TEM), electron microdiffraction, and X-ray diffractograms. Magnetic measurements, Mossbauer, and electron paramagnetic resonance (EPR) spectral studies indicated that the as-prepared amorphous particles were superparamagnetic. The Mossbauer parameters and the significantly low (45 emu/g) observed saturation of magnetization of the annealed sample, compared to that of the bulk sample (72 emu/g), reflected its nanocrystalline nature.

Crystal grain nucleation in amorphous silicon

Abstract: The solid phase crystallization of chemical vapor deposited amorphous silicon films onto oxidized silicon wafers, induced either by thermal annealing or by ion beam irradiation at high substrate temperatures, has been extensively developed and it is reviewed here. We report and discuss a large variety of processing conditions. The structural and thermodynamical properties of the starting phase are emphasized. The morphological evolution of the amorphous towards the polycrystalline phase is investigated by transmission electron microscopy and it is interpreted in terms of a physical model containing few free parameters related to the thermodynamical properties of amorphous silicon and to the kinetical mechanisms of crystal grain growth. A direct extension of this model explains also the data concerning the ion-assisted crystal grain nucleation.

Thin‐Film Crystalline SnO2‐Lithium Electrodes

Abstract: Crystalline SnO{sub 2} thin films have been investigated as possible negative electrodes for lithium-ion batteries. The films have been cycled electrochemically vs. lithium and shown reversible capacity as high as 500 mAh/g over more than 100 cycles. The substantial irreversibility during the first cycle can be explained by the formation of metallic tin and amorphous lithium oxide. This last phase probably plays an important role in allowing the thin-film electrode to contract and expand during the cycling process.

Resonant Dipole-Dipole Energy Transfer in a Nearly Frozen Rydberg Gas

Abstract: In a room temperature vapor of Rb Rydberg atoms, resonant dipole-dipole energy transfer occurs via binary collisions. In contrast, in the $300\ensuremath{\mu}\mathrm{K}$ vapor produced by a magneto-optical trap, the atoms are nearly frozen in place and many atoms interact simultaneously, as in an amorphous solid. As a result of the simultaneous multiple atom interactions, the energy transfer resonances are broadened substantially in frequency.

Structural properties of microcrystalline silicon in the transition from highly crystalline to amorphous growth

Abstract: The growth of microcrystalline silicon prepared by plasma-enhanced chemical vapour deposition depends on the deposition conditions and yields films with variable content of crystalline grains, amorphous network, grain boundaries and voids. The changes in the structural properties of a series of films grown under a variation of the dilution of the process gas silane in hydrogen, which induces a transition from highly crystalline to amorphous growth, were investigated. The evolution of the crystalline volume fraction was quantitatively analysed by Raman spectroscopy and X-ray diffraction. The results confirm the need for proper correction of the Raman data for optical absorption and Raman cross-section. Transmission electron microscopy was used to investigate the characteristics and the variation in the microstructure. Upon increasing the silane concentration the strong columnar growth with narrow grain boundaries degrades towards the growth of small irregularly shaped grains enclosed in an amorpho...

Protective coatings for negative electrodes

Abstract: Disclosed is an alkali metal negative electrode having a protective layer. Specifically, the disclosed negative electrode includes a glassy or amorphous surface protective layer which conducts alkali metal ions but effectively blocks the alkali metal in the electrode from direct contact with the ambient. The protective layer has improved smoothness and reduced internal stress in comparison to prior protective layers such as those formed by sputtering. In a specific embodiment, the protective layer is formed on the lithium metal electrode surface by a plasma assisted deposition technique.

Materials modification by electronic excitation

Abstract: Excitonic mechanisms of defect formation and of sputtering from surfaces, induced as a consequence of exciton relaxation, are effective in a limited class of wide-gap materials, such as alkali halides, alkaline earth fluorides and fused quartz. In this paper, we point out that modification by electronic excitation can be achieved in a far wider range of materials. First, referring to STM observations of semiconductor surfaces irradiated by laser or intense-electron beams, we show that atomic emissions with electronic origin do take place even in materials in which the bandgap energy is smaller than the energy to remove an atom from the surface. The yield of this process is linear with the beam intensity for higher incident energies, but superlinear for lower incident energies. Secondly we analyse the phenomena of laser damage and laser ablation in a variety of wide-gap materials, emphasizing the role played by defect creation in the bulk, and atomic emissions from surfaces originating from excitation of existing defects. Finally, we discuss the amorphisation of less-ionic oxides and semiconductors by electron- and ion-beam irradiation in terms of nucleation followed by radiation-induced reactions at the interface between the crystalline and amorphous regions. The similarities and differences of the interface reactions induced by electronic excitation and by hot zones in collision cascades are discussed.

Tunneling Systems in Amorphous and Crystalline Solids

Abstract: 1. Introduction.- 2. Heat Release in Solids.- 3. Crossover to Phonon-Assisted Tunneling in Insulators and Metals.- 4. Influence of Tunneling Systems on the Acoustic Properties of Disordered Solids.- 5. Interactions Between Tunneling Defects in Amorphous Solids.- 6. Investigation of Tunneling Dynamics by Optical Hole-Burning Spectroscopy.- 7. Tunneling of H and D in Metals and Semiconductors.- 8. Microscopic View of the Low-Temperature Anomalies in Glasses.- 9. Beyond the Standard Tunneling Model: The Soft-Potential Model.- References.

Method and apparatus for providing a conductive, amorphous non-stick coating

Abstract: A conductive, non-stick coating (62) is provided using a ceramic material which is conductive, flexible and provides a surface which exhibits the property of lubricity. A room or near room temperature manufacturing process produces a coating of titanium nitride on a substrate, where the coating is amorphous if the substrate is a solid material including plastics, composites, metals, magnets and ceramics, enabling the substrate to bend without damaging the coating. The coating can also be applied as a conformal coating on a variety of substrate shapes, depending upon the application. The coating is biocompatible and can be applied to a variety of medical devices.

Nickel induced crystallization of amorphous silicon thin films

Abstract: Nickel (Ni) induced crystallization of amorphous silicon (a-Si) has been studied by selective deposition of Ni on a-Si thin films. The a-Si under and near the Ni-covered regions was found to be crystallized after heat treatment at 500 °C from 1 to 90 h. Micro-Auger electron spectroscopy revealed that a large amount of Ni stayed in the region under the original Ni coverage, but no Ni was detected either in the crystallized region next to the Ni coverage or in the amorphous region beyond the front of the laterally crystallized Si. X-ray photoelectron spectroscopy revealed a nonuniform Ni distribution through the depth of the crystallized film under the original Ni coverage. In particular, a Ni concentration peak was found to exist at the interface of the crystallized Si and the buried oxide. It was found that a layer of 5-nm-thick Ni could effectively induce lateral crystallization of over 100 μm of a-Si, but the lateral crystallization rate was found to decrease upon extended heat treatment. Transmission e...

Improved equivalent circuit and analytical model for amorphous silicon solar cells and modules

Abstract: An improved equivalent circuit for hydrogenated amorphous silicon (a-Si:H) solar cells and modules is presented. It is based on the classic combination of a diode with an exponential current-voltage characteristic, of a photocurrent source plus a new term representing additional recombination losses in the i-layer of the device. This model/equivalent circuit matches the I(V) curves of a-Si:H cells over an illumination range of six orders of magnitude. The model clearly separates effects related to the technology of the device (series and parallel resistance) and effects related to the physics of the p-i-n junction (recombination losses). It also allows an effective /spl mu//spl tau/ product in the i-layer of the device to be determined, characterizing its state of degradation.

Pressure-Induced Amorphization and Negative Thermal Expansion in ZrW2O8

Abstract: It has recently been shown that zirconium tungstate (ZrW2O8) exhibits isotropic negative thermal expansion over its entire temperature range of stability. This rather unusual behavior makes this compound particularly suitable for testing model predictions of a connection between negative thermal expansion and pressure-induced amorphization. High-pressure x-ray diffraction and Raman scattering experiments showed that ZrW2O8 becomes progressively amorphous from 1.5 to 3.5 gigapascals. The amorphous phase was retained after pressure release, but the original crystalline phase returned after annealing at 923 kelvin. The results indicate a general trend between negative thermal expansion and pressure-induced amorphization in highly flexible framework structures.

Spectroscopic determination of the structure of amorphous nitrogenated carbon films

Abstract: Studies on structure and electronic properties of amorphous nitrogenated carbon films prepared in dual electron cyclotron resonance–radio frequency plasma from a mixture of methane and nitrogen are presently reported. These films are characterized by Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, x-ray photoemission spectroscopy (XPS), ultraviolet photoemission spectroscopy (UPS), electrical conductivity measurement, and optical absorption spectroscopy. Symmetry breaking of aromatic rings are at a very small amount of nitrogen incorporation is understood from FTIR spectra. The relative contribution of C=N and C–N bonds is found to change with the variation of the nitrogen content in the samples, which shows a similar trend with the shift of the G peak to a higher wave number and the increase of the ID/IG ratio. From decomposition of XPS C 1s and N 1s peaks a three-phase model of CN bonds is proposed. UPS valence band spectra obtained by using a Helium II source, are decomposed into p-...