Showing papers on "Voltage published in 2012"

Electrode Materials for Rechargeable Sodium-Ion Batteries: Potential Alternatives to Current Lithium-Ion Batteries

Abstract: Lithium (Li)-ion batteries (LIB) have governed the current worldwide rechargeable battery market due to their outstanding energy and power capability. In particular, the LIB's role in enabling electric vehicles (EVs) has been highlighted to replace the current oil-driven vehicles in order to reduce the usage of oil resources and generation of CO2 gases. Unlike Li, sodium is one of the more abundant elements on Earth and exhibits similar chemical properties to Li, indicating that Na chemistry could be applied to a similar battery system. In the 1970s-80s, both Na-ion and Li-ion electrodes were investigated, but the higher energy density of Li-ion cells made them more applicable to small, portable electronic devices, and research efforts for rechargeable batteries have been mainly concentrated on LIB since then. Recently, research interest in Na-ion batteries (NIB) has been resurrected, driven by new applications with requirements different from those in portable electronics, and to address the concern on Li abundance. In this article, both negative and positive electrode materials in NIB are briefly reviewed. While the voltage is generally lower and the volume change upon Na removal or insertion is larger for Na-intercalation electrodes, compared to their Li equivalents, the power capability can vary depending on the crystal structures. It is concluded that cost-effective NIB can partially replace LIB, but requires further investigation and improvement.

A New Battery/UltraCapacitor Hybrid Energy Storage System for Electric, Hybrid, and Plug-In Hybrid Electric Vehicles

Abstract: In this paper, a new battery/ultracapacitor hybrid energy storage system (HESS) is proposed for electric drive vehicles including electric, hybrid electric, and plug-in hybrid electric vehicles. Compared to the conventional HESS design, which uses a larger dc/dc converter to interface between the ultracapacitor and the battery/dc link to satisfy the real-time peak power demands, the proposed design uses a much smaller dc/dc converter working as a controlled energy pump to maintain the voltage of the ultracapacitor at a value higher than the battery voltage for the most city driving conditions. The battery will only provide power directly when the ultracapacitor voltage drops below the battery voltage. Therefore, a relatively constant load profile is created for the battery. In addition, the battery is not used to directly harvest energy from the regenerative braking; thus, the battery is isolated from frequent charges, which will increase the life of the battery. Simulation and experimental results are presented to verify the proposed system.

High-detectivity multilayer MoS(2) phototransistors with spectral response from ultraviolet to infrared.

Abstract: Phototransistors based on multilayer MoS(2) crystals are demonstrated with a wider spectral response and higher photoresponsivity than single-layer MoS(2) phototransistors. Multilayer MoS(2) phototransistors further exhibit high room temperature mobilities (>70 cm(2) V(-1) s(-1) ), near-ideal subthreshold swings (~70 mV decade(-1) ), low operating gate biases (<5 V), and negligible shifts in the threshold voltages during illumination.

Induction of coherent magnetization switching in a few atomic layers of FeCo using voltage pulses

Abstract: The magnetization direction of a metallic magnet has generally been controlled by a magnetic field or by spin-current injection into nanosized magnetic cells. Both these methods use an electric current to control the magnetization direction; therefore, they are energy consuming. Magnetization control using an electric field is considered desirable because of its expected ultra-low power consumption and coherent behaviour. Previous experimental approaches towards achieving voltage control of magnetization switching have used single ferromagnetic layers with and without piezoelectric materials, ferromagnetic semiconductors, multiferroic materials, and their hybrid systems. However, the coherent control of magnetization using voltage signals has not thus far been realized. Also, bistable magnetization switching (which is essential in information storage) possesses intrinsic difficulties because an electric field does not break time-reversal symmetry. Here, we demonstrate a coherent precessional magnetization switching using electric field pulses in nanoscale magnetic cells with a few atomic FeCo (001) epitaxial layers adjacent to a MgO barrier. Furthermore, we demonstrate the realization of bistable toggle switching using the coherent precessions. The estimated power consumption for single switching in the ideal equivalent switching circuit can be of the order of 10(4)k(B)T, suggesting a reduction factor of 1/500 when compared with that of the spin-current-injection switching process.

Collective bulk carrier delocalization driven by electrostatic surface charge accumulation

Abstract: In the classic transistor, the number of electric charge carriers--and thus the electrical conductivity--is precisely controlled by external voltage, providing electrical switching capability. This simple but powerful feature is essential for information processing technology, and also provides a platform for fundamental physics research. As the number of charges essentially determines the electronic phase of a condensed-matter system, transistor operation enables reversible and isothermal changes in the system's state, as successfully demonstrated in electric-field-induced ferromagnetism and superconductivity. However, this effect of the electric field is limited to a channel thickness of nanometres or less, owing to the presence of Thomas-Fermi screening. Here we show that this conventional picture does not apply to a class of materials characterized by inherent collective interactions between electrons and the crystal lattice. We prepared metal-insulator-semiconductor field-effect transistors based on vanadium dioxide--a strongly correlated material with a thermally driven, first-order metal-insulator transition well above room temperature--and found that electrostatic charging at a surface drives all the previously localized charge carriers in the bulk material into motion, leading to the emergence of a three-dimensional metallic ground state. This non-local switching of the electronic state is achieved by applying a voltage of only about one volt. In a voltage-sweep measurement, the first-order nature of the metal-insulator transition provides a non-volatile memory effect, which is operable at room temperature. Our results demonstrate a conceptually new field-effect device, extending the concept of electric-field control to macroscopic phase control.

Design of pressure-driven microfluidic networks using electric circuit analogy

Abstract: This article reviews the application of electric circuit methods for the analysis of pressure-driven microfluidic networks with an emphasis on concentration- and flow-dependent systems. The application of circuit methods to microfluidics is based on the analogous behaviour of hydraulic and electric circuits with correlations of pressure to voltage, volumetric flow rate to current, and hydraulic to electric resistance. Circuit analysis enables rapid predictions of pressure-driven laminar flow in microchannels and is very useful for designing complex microfluidic networks in advance of fabrication. This article provides a comprehensive overview of the physics of pressure-driven laminar flow, the formal analogy between electric and hydraulic circuits, applications of circuit theory to microfluidic network-based devices, recent development and applications of concentration- and flow-dependent microfluidic networks, and promising future applications. The lab-on-a-chip (LOC) and microfluidics community will gain insightful ideas and practical design strategies for developing unique microfluidic network-based devices to address a broad range of biological, chemical, pharmaceutical, and other scientific and technical challenges.

Flexible Charging Optimization for Electric Vehicles Considering Distribution Grid Constraints

Abstract: In this paper, the basic functions of an electric vehicle charging service provider are described with a focus on the associated optimization problems. A novel method of planning the charging of electric drive vehicles including electricity grid constraints, both voltage and power, is shown. The method establishes an individual charging plan for each vehicle and avoids distribution grid congestion while satisfying the requirements of the individual vehicle owners. The concepts proposed in this paper are tested on a simulated electricity grid. It is shown that both power and voltage constraints due to electric vehicle charging can be avoided using the proposed method.

Improved Transformerless Inverter With Common-Mode Leakage Current Elimination for a Photovoltaic Grid-Connected Power System

Abstract: To eliminate the common-mode leakage current in the transformerless photovoltaic grid-connected system, an improved single-phase inverter topology is presented. The improved transformerless inverter can sustain the same low input voltage as the full-bridge inverter and guarantee to completely meet the condition of eliminating common-mode leakage current. Both the unipolar sinusoidal pulsewidth modulation (SPWM) as well as the double-frequency SPWM control strategy can be applied to implement the three-level output in the presented inverter. The high efficiency and convenient thermal design are achieved thanks to the decoupling of two additional switches connected to the dc side. Moreover, the higher frequency and lower current ripples are obtained by adopting the double-frequency SPWM, and thus the total harmonic distortion of the grid-connected current are reduced greatly. Furthermore, the influence of the phase shift between the output voltage and current, and the influence of the junction capacitances of the power switches are analyzed in detail. Finally, a 1-kW prototype has been simulated and tested to verify the theoretical analysis of this paper.

Impact of High PV Penetration on Voltage Profiles in Residential Neighborhoods

Abstract: The objective of this paper is to provide an assessment on voltage profiles in residential neighborhoods in the presence of photovoltaic (PV) systems. The network was modeled in PSCAD using common feeder characteristics that Canadian system planners use in suburban residential regions. A simulation study was performed to investigate potential voltage rise issues in the network up to 11.25% total PV penetration in the feeder and LV transformer capacity penetration up to 75%. Results indicate that the PV penetration level should not adversely impact the voltage on the grid when the distributed PV resources do not exceed 2.5 kW per household on average on a typical distribution grid. Moreover, the role of feeder impedance, feeder length, and the transformer short circuit resistance in the determination of the voltage rise is quantified.

A New Multilevel Converter Topology With Reduced Number of Power Electronic Components

Abstract: In this paper, a new topology for cascaded multilevel converter based on submultilevel converter units and full-bridge converters is proposed. The proposed topology significantly reduces the number of dc voltage sources, switches, IGBTs, and power diodes as the number of output voltage levels increases. Also, an algorithm to determine dc voltage sources magnitudes is proposed. To synthesize maximum levels at the output voltage, the proposed topology is optimized for various objectives, such as the minimization of the number of switches, gate driver circuits and capacitors, and blocking voltage on switches. The analytical analyses of the power losses of the proposed converter are also presented. The operation and performance of the proposed multilevel converter have been evaluated with the experimental results of a single-phase 125-level prototype converter.

Smart electric vehicle (ev) charging and grid integration apparatus and methods

Abstract: An expert system manages a power grid wherein charging stations are connected to the power grid, with electric vehicles connected to the charging stations, whereby the expert system selectively backfills power from connected electric vehicles to the power grid through a grid tie inverter (if present) within the charging stations. In more traditional usage, the expert system allows for electric vehicle charging, coupled with user preferences as to charge time, charge cost, and charging station capabilities, without exceeding the power grid capacity at any point. A robust yet accurate state of charge (SOC) calculation method is also presented, whereby initially an open circuit voltage (OCV) based on sampled battery voltages and currents is calculated, and then the SOC is obtained based on a mapping between a previously measured reference OCV (ROCV) and SOC. The OCV-SOC calculation method accommodates likely any battery type with any current profile.

Temperature Measurement of Power Semiconductor Devices by Thermo-Sensitive Electrical Parameters—A Review

Abstract: This paper proposes a synthesis of different electrical methods used to estimate the temperature of power semiconductor devices. The following measurement methods are introduced: the voltage under low current levels, the threshold voltage, the voltage under high current levels, the gate-emitter voltage, the saturation current, and the switching times. All these methods are then compared in terms of sensitivity, linearity, accuracy, genericity, calibration needs, and possibility of characterizing the thermal impedance or the temperature during the operation of the converter. The measurement of thermo-sensitive parameters of wide bandgap semiconductors is also discussed.

A Switched-Capacitor Inverter Using Series/Parallel Conversion With Inductive Load

Abstract: A novel switched-capacitor inverter is proposed. The proposed inverter outputs larger voltage than the input voltage by switching the capacitors in series and in parallel. The maximum output voltage is determined by the number of the capacitors. The proposed inverter, which does not need any inductors, can be smaller than a conventional two-stage unit which consists of a boost converter and an inverter bridge. Its output harmonics are reduced compared to a conventional voltage source single phase full bridge inverter. In this paper, the circuit configuration, the theoretical operation, the simulation results with MATLAB/SIMULINK, and the experimental results are shown. The experimental results accorded with the theoretical calculation and the simulation results.

Interleaved piezoelectric tactile interface

Abstract: A piezoelectric tactile input device and method in a computing environment. An embodiment disclosed herein includes a touch screen having several piezoelectric regions within a piezoelectric material layer that may generate a voltage when deformed in a localized area. The piezoelectric layer may be disposed between sensor layers of rows and columns of sensor traces for detecting the voltage generated at any particular piezoelectric region. The detected voltage signals may then be used to extrapolate the position of the localized area in which the piezoelectric layer was deformed (e.g., from a finger touch or a stylus). Further, because the piezoelectric layer generates a greater voltage in the presence of a greater pressure, the device may further decipher a relative level of force for the tactile input on the touch screen and detect multiple touch locations.

High fidelity electrical model with thermal dependence for characterization and simulation of high power lithium battery cells

Abstract: The growing need for accurate simulation of advanced lithium cells for powertrain electrification demands fast and accurate modeling schemes. Additionally, battery models must account for thermal effects because of the paramount importance of temperature in kinetic and transport phenomena of electrochemical systems. This paper presents an effective method for developing a multi-temperature lithium cell simulation model with thermal dependence. An equivalent circuit model with one voltage source, one series resistor, and a single RC block was able to account for the discharge dynamics observed in the experiment. A parameter estimation numerical scheme using pulse current discharge tests on high power lithium (LiNi-CoMnO 2 cathode and graphite-based anode) cells under different operating conditions revealed dependences of the equivalent circuit elements on state of charge, average current, and temperature. The process is useful for creating a high fidelity model capable of predicting electrical current/voltage performance and estimating run-time state of charge. The model was validated for a lithium cell with an independent drive cycle showing voltage accuracy within 2%. The model was also used to simulate thermal buildup for a constant current discharge scenario.

Zero-Current Switching Switched-Capacitor Zero-Voltage-Gap Automatic Equalization System for Series Battery String

Abstract: The series battery string or supercapacitor string automatic equalization system based on quasi-resonant switched-capacitor converter is presented in this paper. It realizes the zero-voltage gap between cells and allows maximum energy recovery in a series battery system or supercapacitor system. It not only inherits the advantage of conventional switched-capacitor battery cell balancing system, but also overcomes the drawback of conduction loss, switching loss, and finite voltage difference among battery cells. All switches are MOSFET and controlled by just a pair of complementary signals in synchronous trigger pattern and the resonant tanks operate alternatively between the two states of charging and discharging. Zero-current switching and zero-voltage gap are achieved in this paper. Different resonant tank designs can meet the needs of different balancing time to meet the needs of different energy storage devices. Experimental results indicate that the efficiency of the system is high exceeding 98%. The system is very suitable for balancing used in battery management system.

Operation Mode Analysis and Peak Gain Approximation of the LLC Resonant Converter

Abstract: With the advantage of achieving zero voltage switching for a wide input voltage range, the LLC resonant topology has become increasingly popular for use in high power density and high-efficiency power converter applications. However, when the LLC converter is applied to wide input voltage range applications, the widely used fundamental harmonic approximation is incapable of guiding the design due to its inaccuracy. Thus an accurate LLC converter model is desired. In this paper, a generalized mode analysis is presented that provides highly accurate prediction on resonant current and voltage behavior and dc gain characteristic. Also, because operation modes are affected by load, frequency, and gain conditions, the boundaries and distribution of modes are discussed and illustrated. Based on the mode analysis, an approximation method is developed to estimate the peak gain point, which is useful in LLC design. This approximation demonstrates high accuracy within the simulation results. An experimental prototype is built to verify the analysis.

Silicon Carbide Power Transistors: A New Era in Power Electronics Is Initiated

Abstract: During recent years, silicon carbide (SiC) power electronics has gone from being a promising future technology to being a potent alternative to state-of-the-art silicon (Si) technology in high-efficiency, highfrequency, and high-temperature applications. The reasons for this are that SiC power electronics may have higher voltage ratings, lower voltage drops, higher maximum temperatures, and higher thermal conductivities. It is now a fact that several manufacturers are capable of developing and processing high-quality transistors at cost that permit introduction of new products in application areas where the benefits of the SiC technology can provide significant system advantages.

Voltage-dependent conductance of a single graphene nanoribbon

Abstract: The conductance properties of a narrow graphene nanoribbon are correlated with its electronic states over a wide range of bias voltages using a scanning tunnelling microscope

A Portable 2-Transistor Picowatt Temperature-Compensated Voltage Reference Operating at 0.5 V

Abstract: Sensing systems such as biomedical implants, infrastructure monitoring systems, and military surveillance units are constrained to consume only picowatts to nanowatts in standby and active mode, respectively. This tight power budget places ultra-low power demands on all building blocks in the systems. This work proposes a voltage reference for use in such ultra-low power systems, referred to as the 2T voltage reference, which has been demonstrated in silicon across three CMOS technologies. Prototype chips in 0.13 μm show a temperature coefficient of 16.9 ppm/°C (best) and line sensitivity of 0.033%/V, while consuming 2.22 pW in 1350 μm2. The lowest functional Vdd 0.5 V. The proposed design improves energy efficiency by 2 to 3 orders of magnitude while exhibiting better line sensitivity and temperature coefficient in less area, compared to other nanowatt voltage references. For process spread analysis, 49 dies are measured across two runs, showing the design exhibits comparable spreads in TC and output voltage to existing voltage references in the literature. Digital trimming is demonstrated, and assisted one temperature point digital trimming, guided by initial samples with two temperature point trimming, enables TC <; 50 ppm/°C and ±0.35% output precision across all 25 dies. Ease of technology portability is demonstrated with silicon measurement results in 65 nm, 0.13 μm, and 0.18 μm CMOS technologies.

Display device with integrated touch screen

Abstract: A display device with an integrated touch screen according to an embodiment, includes a display panel including a touch screen provided in an active area of the display panel, and a display driver circuit provided in an inactive area of the display panel, the touch screen including a plurality of driving electrodes, each of the driving electrodes including a plurality of sub driving electrodes positioned in the active area of the display panel but electrically connected to each other in the inactive area of the display panel, the touch screen further including a plurality of sensing electrodes disposed between the sub driving electrodes and formed in the active area of the panel, and the display driver circuit configured to apply a common voltage to the driving electrodes and the sensing electrodes or a touch driving voltage to the driving electrodes according to a driving mode of the display panel.

Efficiency Analysis of Drive Train Topologies Applied to Electric/Hybrid Vehicles

Abstract: One of the most important research topics in drive train topologies applied to electric/hybrid vehicles is the efficiency analysis of the power train components, including the global drive efficiency. In this paper, two basic traction electric drive systems of electric/hybrid vehicles are presented and evaluated, with a special focus on the efficiency analysis. The first topology comprises a traditional pulsewidth-modulation (PWM) battery-powered inverter, whereas in the second topology, the battery is connected to a bidirectional dc-dc converter, which supplies the inverter. Furthermore, a variable-voltage control technique applied to this second topology is presented, which allows for the improvement of the drive overall performance. Some simulation results are presented, considering both topologies and a permanent-magnet synchronous motor (PMSM). An even more detailed analysis is performed through the experimental validation. Particular attention is given to the evaluation of the main drive components efficiency, including the global drive efficiency, presented in the form of efficiency maps. Other parameters such as motor voltage distortion and power factor are also considered. In addition, the comparison of the two topologies takes into account the drive operation under the motoring and regenerative-braking modes.

Compound semiconductor device and method of manufacturing the same

Abstract: Two layers of protection films are formed such that a sheet resistance at a portion directly below the protection film is higher than that at a portion directly below the protection film. The protection films are formed, for example, of SiN film, as insulating films. The protection film is formed to be higher, for instance, in hydrogen concentration than the protection film so that the protection film is higher in refractive index the protection film. The protection film is formed to cover a gate electrode and extend to the vicinity of the gate electrode on an electron supplying layer. The protection film is formed on the entire surface to cover the protection film. According to this configuration, the gate leakage is significantly reduced by a relatively simple configuration to realize a highly-reliable compound semiconductor device achieving high voltage operation, high withstand voltage, and high output.

Active-Power Control of Individual Converter Cells for a Battery Energy Storage System Based on a Multilevel Cascade PWM Converter

Abstract: The battery energy storage system is an essential enabling device of the smart grid, because it helps grid connection of massive renewable energy resources. This paper has a brief discussion on a battery energy storage system based on a multilevel cascade pulsewidth-modulated (PWM) converter for its practical use. The active-power control of individual converter cells is presented to make it possible to charge and discharge the battery units at different power levels while producing a three-phase balanced line-to-line voltage. This results in the maximum utilization of battery energy even when the power-handling capabilities of the battery units differ. Experimental results obtained from a 200-V, 10-kW, 3.6-kWh battery energy storage system verify the effectiveness of the presented active-power control.